Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

How did you get started in woodworking?

Posts

How did you get started in woodworking?

#1

How did you get started in woodworking?

Carol - now in NC Nebraska

>This topic came up on another forum. I thought it such a good topic that I posted it here. I know lots of you through the Internet, some for years. It would be interesting to see how you got 'bitten'. I'll begin.

No real woodworking genes in my family. My grandfather (a dairy farmer) repaired broken furniture during the winter months for the extended family. His 'shop' was a windowless hut with a dirt floor, equipped with a few hand tools. He brought his glue-ups into the kitchen (huge room with a wood cooking stove).

When I am about 6-7 he set me to making 'pine curlie-ques' with a handplane. I finally filled an entire bucket, learning along the way to fettle the plane and plane perpendicular edges. Only tools were a vise, handplane, and try square. My work was validated when he took the bucket of plane shavings into the house and gave them to my grandmother for fire starters for her wood stove. The seed was planted.

Of course I grew up in the era that girls were not permitted to go to woodshop in school. But I collected cheap tools and muddled along with the help of Popular Mechanics magazine - mostly dreaming. I always got into big trouble using the tools given to my brothers who had little interest in using them. After school I started buying tools. What a help a woodworking forums would have been. But that was before you-know-who 'invented' the Internet. LOL

In the late '80's I started woodworking classes in a community college. By the middle '90's I was a full-time woodworker and back teaching at that same community college. That led to demonstrating at woodworking shows around the country, writing a book, and then speaking at home remodeling/improvement/garden shows. An auto accident forced the closure of my business and I moved to Arizona to "retire." That led me to enter seminary to follow another passion. Along the way I acquired a Jet mini-lathe, took a few classes on turning, and started that slippery slope. :)

Good question!

Re: How did you get started in woodworking?

#2

First, I was born.

Brian Hahn in SW Wisconsin

>My parents started building a new home when I was 6. A (small) section of the sheathing was nailed by a 6 year old with a 12-ounce hammer. That hammer is now on its fourth handle and I still use it. A few years later I got my first lessons in sanding and finishing when I carved a model sailboat. I did a lot of carving when I was a Boy Scout, which may be why it doesn't interest me any more. My Dad bought a cheap lathe after he retired and I turned my first bowl in 1980 when I visited them at Christmas time. I bought my first lathe two years later.

Woodworking in some form has consistently been one of my main hobbies. Gardening is the only other hobby that has been as consistent. All of my other hobbies have lasted less than a decade, the most notable being electronics and photography.

Re: How did you get started in woodworking?

#3

Re: How did you get started in woodworking?

robo hippy

>I was just over 2 years old, and went out to the garage and found a bag of nails, and a hammer and pounded them all into the dirt floor, which now as a parent I can see as one of those things where you can be a little mad, and very proud. I did numerous other little things from building balsa models and club houses. I got into concrete construction, and every one I worked for told me I was too fussy to be a concrete man, and I said thank you. A work injury got me a disability settlement which was just enough to get all the basic tools for a wood shop, so I took the leap. I never looked back.

robo hippy

Re: How did you get started in woodworking?

#4

I owe it all to my ex husband

Ruth Niles

>If he hadn't been a total jerk, I would have done nothing but raise kids, cook, clean and be a 4-H leader and get old, play bingo and watch TV.

I had to support 4 kids alone, besides waitressing I was a very good seamstress. After 97 1/2 yrs. of this, I decided something new was in order, if I could take material and make something, then I could take wood and make something. I took an adult ed. class, wood teacher was away, metal teacher took over, didn't learn a thing except not to hold wood with my hands in front of the bandsaw blade.

My kids went in together, bought me a Craftsman monotube lathe and a set of Sears turning tools, I went to the library, took out the only 2 books they had, one Raffan's "Turning Projects", opened the book behind the lathe and started turning. I took the book out for 2 weeks, renewed it for 2 more, it had to stay in the library 1 week before I could take it out again. My chips are probably still in that book and that was 1998. I turned one of everything in that book (I lied, not the pool stick nor the big ugly mouse garden thing). They weren't very good, but I learned. For 5 yrs. I thought Richard Raffan and I were the only 2 woodturners in the world!

My downfall (yes, downfall) was when I attended my first AAW Symposium (RI) and I saw all those lathes, tools, turnings, finishes........ too much!

The End

Re: How did you get started in woodworking?

#5

Re: How did you get started in woodworking?

Jennifer@Indy.USA

>In 1993 I bought a 1925 worn out Bungalow and had to fix it up myself, because like Ruth I was/am a single parent and didn't have the $$ to pay someone else to do it. I bought a Makita chop saw and that was the beginning. A full shop full of the essential tools later, I Took a night adult edu. woodworking class at the high school down the street and met a man named Carole Sipes. Carole was a woodturner and that's all he did in the class. While I was still measuring my flat boards Carole was over at a big old Oliver lathe making cool stuff hand over fist! I'll never forget the night he walked in with a huge cherry log and walked out with a tall plant stand! He convinced me to come to a local AAW chapter meeting and then two weeks later at the Indy Woodworking show I saw a JET mini lathe. It came home with me and then grew into a big green lathe and that's the end of my story.

:)

Re: How did you get started in woodworking?

#6

Re: How did you get started in woodworking?

Dinyar Chavda

>My wife wanted me to have a hobby so that I would not drive her nuts when we retired.

So far, she's sane.

Re: How did you get started in woodworking?

#7

Re: How did you get started in woodworking?

Ed Wujciak

>In 1952, when I was 6, my dad bought a new Shopsmith 10ER, display model, for $175 (big money). For the next 15 years or so, in his free time, he built shelves, cabinets, and other enhancements for our home. He even made some things on the lathe, one of which I still have. Whenever he was working, I watched. He enjoyed it so much and got such satisfaction from creating things. I inherited that gene, and the Shopsmith. I learned to turn on it. Mediocre lathe, but an amazing machine - replaced only a motor capacitor and a v-belt in 55 years. These days I mostly turn on my Nova 1624-44 and use the Shopsmith for a saw, sander, and drill press. Sawdust in the blood I guess. I enjoy the process and enjoy never having to hurry.... It's the journey, not the destination.

Re: How did you get started in woodworking?

#8

Re: How did you get started in woodworking?

Mike Hamilton

>Maternal Grandpa did flat work for himself and turned salt and pepper shakers for extra income. Paternal side of the family was subsistence farmers in WV, so 'doing for yourself' was a survival skill. The genes were right.

BA in Econ in the early 70's with no desire for grad school or wearing a tie. A desire to 'make something', memories of grandpa's shop, and living in a house full of handmade furniture and wood working just seemed the thing to try. Two years of kitchen cabinets, a year of antique restoration, and a year in a midsized shop in Durham, NC making mahogany period pieces gave me all the training I needed at minimum wage. It has been my constant hobby since. I did have the joy of sharing shop space with my dad for a couple decades before he passed.

Thanks for triggering lots of good memories,

Mike Hamilton

Plainfield, IN

Re: How did you get started in woodworking?

#9

Mike Stafford

At an early age my parents....

Mike Stafford

>decided that they could no longer feed me. My father handed me an axe and pointed toward the woods and said, "Go make a life for yourself." I proceeded to clear cut most of the 35 acres of timber....Oh, you don't believe any of that, huh?

My father was my impetus for getting interested in woodworking. He and I built our house it seems. We spent all our free time working on the house; building cabinets, bookcases, additional rooms etc. My father was not into decorative woodworking he was into necessity woodworking. We built what we needed.

As I got older I became more interested in building things for myself. I built boxes to store my treasures in and small furniture pieces that probably resembled orange crates for my room. When I went to college I built all kinds of little furniture and items to organize my room.

I met the love of my life and for a wedding gift I built a table and 4 chairs with my father's help. I also built a tall skinny hutch to store our small kitchen appliances.

Over the next few years I built small furniture with my closet shop working on the pation or porch of the apartments we lived in. I had a workbench that stored its own legs with a front vise that I built and a Workmate and every portable power tool imaginable, drills, saws, planers, routers etc. I built furniture for us and as gifts for the rest of the family. Small things like end tables, table lamps etc.

From there I moved into wooden toys when my son was born and that was the first time I did any turning as I needed boilers and smokestacks for train locomotives. I had a house and a Shopsmith by this time and thought I was well equipped. I still have a Shopsmith, by the way,(my third). I continued to build boxes and small furniture.

I wanted to turn some decorative handles, finials for some of my artsy/schmartsy boxes and tried it on the Shopsmith. The tools I had were too large so I went looking for smaller tools. I visited a large woodworking store in the big city and found the tools as well as Richard Raffan's book on "Turning Boxes." I bought the book, then I bought a lathe and I haven't looked back.....

Re: How did you get started in woodworking?

#10

Re: How did you get started in woodworking?

Carole Valentine

>My Father's degree was in forestry and even though he was not a woodworker, he instilled within me a love for trees and wood (and all of nature for that matter.) After I had moved back to the Shore and bought my house, I decided I wanted to build a picnic table and benches for my backyard. My Mom gave me a Bosch 10" slider for my birthday an away I went. I soon had a shop full of flatwork tools and machinery. I discovered that I was not much of a "flat" person - I would measure six times and still end up cutting wrong. The last flatwork project I ever worked on was a small walnut candle stand which just happened to require a turned column. I bought a Jet mini for that project and...well you know the rest. I have no clue where my router is, my tablesaw is covered with blanks and chunks of wood, the jointer and planer are about to be sold and the shop floor is dominated by two lathes and about a foot of shavings. The candle stand was never finished.

Re: How did you get started in woodworking?

#11

It was to cold to skydive

jeff myroup

>About five years ago my father gave me all his woodworking equipment. At the time I was an avid Skydiver and had no real interest in woodworking. I get laid off in the winter and since it was to cold to jump, I was watching Dave Hout's woodturing show on DIY. I knew the shop smith had all the parts to turn, so I went out and cut a limb off a tree and started turning. I had no clue what the tools where and had to go back in the house and search the net. I found a bunch of info, and learned what the tools where and how to present them. That weekend I told my wife I was going to go out and make a bowl. That day I discovered the hardest wood I had ever seen. I ended up turning an end grain Osage Orange bowl, with a spindle gouge and scraper. It took all day! I only had a disc sander for sharpening. I turned on that shop smith for 4 years, besides the bad run-out, and it being way to short (I am 6'5") it served me well. I see that bowl everyday, and am still suprised at were I ended up. I have not jumped for three years, anyone want to buy my rig?

Jeff

Re: How did you get started in woodworking?

#12

Re: It was to cold to skydive

jeff myroup

>My days before the addiction, or I guess you could say previous addiction


img

Re: How did you get started in woodworking?

#13

Steven Antonucci

I started hammering nails with my grandfather

steve antonucci

>he died when I was 12, but the urge to make stuff was always there. He wasn't very handy, but he tried because money was tight.

When high school came around, I took two years of shop, but it didn't fit my academic schedule my junior year (1983), so I didn't make anything for a long time.

Fast forward to my wife and I just starting out (1995). I started getting the urge to make stuff when I priced furniture. Money was tight (a recurring theme in most folks lives), and I loved a table in the American Woodworker magazine, so I decided to build it. A few tables later, I was fed up with my lack of finishing skills and a house full of so-so furniture.

I saw a pen in one of the magazines (~1998), and since my wife loved pens, I decided to buy a lathe and turn one for her. When everyone I knew owned a pen of mine, I started making bowls and then hollowforms. Now, I mostly turn- although I have a small shelf I'm in the middle of putting together for the hallway. First flat project in years...

Steven

Re: How did you get started in woodworking?

#14

Re: How did you get started in woodworking?

Wally Dickerman in Arizona

>I was raised on a small farm and we used wood for cooking and for heating. When I was quite small, I used my father's chopping block for my workbench. It was just about the right height. I got in trouble for driving nails into it which of course dulled my father's axe.

In highschool we had a large Oliver lathe which nobody used except for the ocassional spindle. I found a chunk of walnut and decided to turn a bowl. The shop teacher didn't know any more about bowl turning than I did, but I managed to get the bowl turned. My sister has it tucked away someplace. That was in 1936 and I was 15 years old. That bowl must have ignited a spark. I worked in a logging camp that summer for $2 a day. I had in mind buying a Ford Model A roadster, which I eventually did, (a 1931 and I paid $125 for it). But first I bought a Sears lathe and some tools and installed it in a corner of the barn. 71 years later I'm still fascinated with woodturning. What a wonderful lifetime hobby.

Wally

Re: How did you get started in woodworking?

#15

Re: How did you get started in woodworking?

Wally Dickerman in Arizona

>I couldn't turn wood on Mondays. The motor for my lathe belonged on my mother's washing machine. It had to be there on Monday morning.

Wally

Re: How did you get started in woodworking?

#16

Re: How did you get started in woodworking?

Carol - now in NC Nebraska

>Now THAT is resourceful! Love it!

Re: How did you get started in woodworking?

#17

Berea college

JKJ in East TN

>Berea College woodworking "industry". Started upstairs in sanding/finishing like all beginners, then moved downstairs to making things.

I remember watching some old guy turn off-axis handles for a special-order casket made entirely from cherry. Someone told me later his name was Rude Osolnik.

JKJ

Re: How did you get started in woodworking?

#18

Keith Tompkins

Re: How did you get started in woodworking?

keith tompkins

>I come from a woodworking family. My grandfather was a cabinetmaker, many on my mother's side were violin makers. I took several shop courses in high school. My senior year I won "craftsman of the year" award in wood shop. I graduated on a Saturday, on the following Monday I started work in a furniture factory. I started as a machine operator, then eventually did all the set-up work for production runs. When the company broke into the commercial dining market, I designed and built the fixtures for producing the chairs. For that, I designed a compound-angle gauge, which the company patented, then built a drill-press based on that design for building the fixtures, which they patented as well. Each fixture was capable of boring all the holes in chairs seats simultaneously. We produced 300 chairs per day. By age 26 I was their highest paid employee, working directly for the company president, designing new furniture pieces, and building prototypes.I received several more design and utility patents while employed there.

I ran my own cabinet shop for years, working with designers and architects. Too many hours, not enough money. Today, I work for New York State Dept. of Corrections....I run a woodworking program at a max. security facility.(excellent benefits and retirement) I train inmates to work in an industrial woodworking setting, hopefully preparing them for gainful employment upon release. We have a fully equipped manufacturing plant...for example,we recently shipped 2,000 completed desks to the state of Louisianna. (Our guarantee? Twenty-five years to Life.) Currently, I am designing the corriculum to train inmates to operate our three new Onsrud 5-axis CNC routers.

I turn occasionally as well.

Re: How did you get started in woodworking?

#19

Re: How did you get started in woodworking?

Roger Smith

>1st - I work at a sawmill during the summers in high school.

2nd - I ran a veneer mill first out of high school.

3rd - I was too poor to hire carpenters, so I did the work myself.

4th - I built a chess table for my grandson. I bought a lathe to turn the pedestal leg. Never had touched a wood turning tool before. Use the skew as a scraper. I had to build the wife kitchen cabinets before she would let me start turning again.

5th - Number 4 was a down payment with outrageous interest rates.

roger

Re: How did you get started in woodworking?

#20

Re:I can't believe you would ......

Jamie Donaldson

>.. actually jump out of a perfectly fine airplane, and I was in the 101st in Vietnam. I was assigned to the Rangers as a SO specialist, so I never had to be jump qualified to rappel out of a Huey!

Re: How did you get started in woodworking?

#21

Re: John- what year was that?

Jamie Donaldson

>

Re: How did you get started in woodworking?

#22

Re:I can't believe you would ......

jeff myroup

>If you had seen our planes, you would jump too. The best jump I ever did was the one were my mom went on a tandem. I went out after and hung out in the distance, so I would not get in the way, but I could still see her excitment. The second best was when I jumped, landed, put on a suit, and got married. The dropzone paid for the wedding and threw a great party. We just had to show up. The local paper covered it for there wedding section. That was cool. Skydivers and from what I have seen of the woodturning community have alot in common. Just a bunch of fun loving folks, who enjoy sharing their knowledge and each other.

Jeff

Re: How did you get started in woodworking?

#23

How Long Ago?

Barbara Gill, Remlik VA

>My husban's two Aunts were in Berea; at least one taught at the college. Their names were Rexie and Nell Gill.

Re: How did you get started in woodworking?

#24

Re: How did you get started in woodworking?

Jennifer@Indy.USA

>What a cute story Wally...I'm really enjoying this thread :)

Re: How did you get started in woodworking?

#25

Re: How did you get started in woodworking?

Ed Karch

>I was born the same year as Wally turned his first bowl. Like Keith my grandfather was a cabnet maker. I have his crosscut saw mounted on the shop wall. Like Carol's dad I am a forester. My dad was raised on a farm and taught us to be self sufficient. His favorite hammer is also in my shop. I have a picture of me at age 4 in the back yard chopping dirt with a hatchet We always had a shop in the basement or garage. We used to pick up orange and lettuce crates from the corner store and salvaged them for wood and nails. I buit a bit of everything from crate wood. I have been making dust and chips ever since, but only learned the world was round about three years ago.