Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

#1 hunter tool in new holders

Posts

#1 hunter tool in new holders

#1

#1 hunter tool in new holders

john lucas

>Below are some photos of the #1 hunter tool in various holders. I have made 3 of them to try out different shapes. I'm looking for a tool that will do all my small hollowing. I wanted a tool that will leave a really good finish so if I make it a box or a highly pierced piece I don't have to sand or at least sand very little.

The hunter tool cuts clean enough but the #1 tool needed a better holder to reach into ornaments and closed hollow vessels. I sat down with my version of a CAD program, a pencil, paper and scissors. I drew various shapes, cut them out and tried them on drawings of ornaments, hollow vessels of all kinds of shapes.

Here's what I've come up with so far. The first shot is a photo of 2 of my tools with the hunter cutter on the tip and the middle one is my homemade John Jordan tool with the #1 cutter installed.

You will notice my tools are canted in the handle. This keeps the tip in line with center of the handle and reduces the twisting. The top one has the cutter angled at 45 degrees and is in a square bar. The bottom one is at 35 degrees and is a flat bar. This one is my favorite shape so far.


img

Re: #1 hunter tool in new holders

#2

close up 

john lucas

>


img

Re: #1 hunter tool in new holders

#3

tool angles in use

john lucas

>Here are examples of how I use these tools. Sorry about the photo. I had the tripod hanging out in space and should have used the cable release but I was in a hurry.

The 35 degree tool is on the bottom. I use it at that angle to remove wood quickly. I tilt it to a steeper angle for clean cuts and it is a little slower.

The top tool is the square shaft tool with the cutter at 45 degrees. I use it really more at about 55 degrees as you see in the photo and it cuts extremely clean. I tried to photograph how clean it is but it doesn't show in a photo.


img

Re: #1 hunter tool in new holders

#4

handmade tool

john lucas

>Up to this point I made the tools partly by hand and partly with my milling machine. I figured most of you don't have that option so I made one this evening with nothing by hand tools. It has a round shank and the cutter sits on top of the tool rather than inset into a milled slot. It doesn't seem to hurt the function doing this. I will write up how to build one in a few days.

This one and the square shank tool both have a little more twisting torque as some lengths but it's not bad. The first tool I made is the best for reducing the twist and reaching into more shapes. It is the hardest to make of course.


img

Re: #1 hunter tool in new holders

#5

Re: handmade tool

Doug Thompson near Cleveland

>I'll be the first to say you did a great job. I like how you pre-set the cutting angle... with the shank flat on the tool rest a roughing or finishing cut should be fool proof, depending on what tool is used... it's well thought out. I see how they could be tough to make, there's a lot going on in a short distance. That insert looks like a RCMT or close to that shape.

Good Job!

Re: #1 hunter tool in new holders

#6

Nicely Done

Ron in Drums PA

>I just read the thread below and I was also thinking along these lines. My thoughts where to have a shape similar to that on the tightest curved 1/2" kelton hollower

Re: #1 hunter tool in new holders

#7

Re: handmade tool

Bob Fawcett

>John,

How about a hex or occtagon handle to help with the torque.

Re: #1 hunter tool in new holders

#8

You are a talented man.

Norm Smith in Nova Scotia

>

Re: #1 hunter tool in new holders

#9

Re: handmade tool

john lucas

>Bob There isn't any torque, at least not more than a regular straight tool without an offset cutter. That's why I designed them this way. Well maybe there is a little on the solid bar tools but even on the one with a handle that is to small it's not problem to control at all. I just used handles that I already had laying around the shop instead of making new ones. I would probably make the handles slightly longer and a little thicker than these. If you hollow a lot you can get carpel tunnel if you use a small handle and grip it tight.

Re: #1 hunter tool in new holders

#10

Re: handmade tool

john lucas

>Doug What is an RCMT? I not familiar with the term. These are Cabide cutters sold by Mike Hunter. I haven't asked but I'm guessing they are commercial cutters of some sort. He has them mounted in very nice custom made shafts that both protect and angle the tip. The 35 degree angled tips are the same angle as his.

I'm glad you don't see the tools up close. I decided these were user tools and didn't spend the time to clean up all the file marks. I kind of disquised them with Gun Blue and lacquer but they are there.

Re: #1 hunter tool in new holders

#11

Re: Nicely Done

john lucas

>Ron I'll have to look up that tool if I can find a photo. By the way, excellent article on the Celtic knot. I read it last night. I've been dying to try that ever since you first discussed it here. I even did a test piece one day to get a better feel for how it worked. I guess I'll have to give it a go. I'm making a sewing kit box today and thought about using it on that but the walls will be mighty thin and I'd be worried about glue separation over the years. On a pen you have the brass insert to help hold the walls together. The walls will be really thin on my sewing kit.

Re: #1 hunter tool in new holders

#12

Re: Nicely Done *LINK*

Ron in Drums PA

>Here is the kelton hollower I was talking about. It's the one on the bottom


Thanks for you kind words John. Here is the goblet that I entered in the AAW's Fall 2005 goblet contest. The walls are about 3/32"-1/8" thick and has held so far. But then nobody is using it to store sewing supplies. (If I did this one over again, I'd make the stem thinner.) I thought the knot got lost on something large like this




Keltic Knot Goblet

Re: #1 hunter tool in new holders

#13

Oh, Oh...teacher! I have a question...

Jennifer@Indy.USA

>John, I'm very intrigued by these Hunter cutters. I am under the assumption that the round cutter is the only thing that comes from him in regards to these tools of yours? Does the star screw come from him too? I love these tools you've made...I'm thinking I may have to give this a try. They look perfect for small work.

Thanks so much for sharing like you do here!

Jen

Re: #1 hunter tool in new holders

#14

Steven Antonucci

You can buy the star screw (Torx) at Lowes or HD

steve antonucci

>At least in my area. Probably a T-15 10-32 5/16" (I'm guessing...)?

Steven

Re: #1 hunter tool in new holders

#15

35 degrees?

Mike Nelson

>John, why the 35 degree angle, especially on a straight boring tool? Doesn't the angle have to change when you go from sides to under the shoulder or bottom?

Re: #1 hunter tool in new holders

#16

Re: Nicely Done

john lucas

>Ron That's the basic principal I was trying to achieve but on hollowers with bent shaft like that you must keep the tool rest on the straight part or you get torque. Bending the shank like this puts the tip on the center line of the handle so it's just like using a straight shank with no torque at all. If you simply bent the bar at one point the cutter would hang out beyond the center. The further from the center the more torque you get. John Jordan's tools work the same way.

By having a continually changing angle like I did on the flat cutter the torque is kept to a minumum with the tool rest anywhere along the shaft. As you move from having the cutter close to the tool rest to where it is lets say 1 1/2" from the tool rest you start to get some torque but it's manageable. As you extend the tool further along the tool rest you get the cutting action more in line with the handle and then you don't have any torque. I found this tool quite relaxing to use at just about any angle and any extension over the tool rest. I made the wide part of the shank 3/8" because I usually hollow through a 1/2" hole. I left it much narrower near the cutter so you can go into the ornament at a pretty extreme angle to cut the bottom of the ornament.

Re: #1 hunter tool in new holders

#17

Re: Oh, Oh...teacher! I have a question...

john lucas

>Jennifer He will furnish the torx screws as well. To make on yourself you will need a 2.5mm tap which is really small. I bought the tape and drill bit from my local radio control hobby store. Not breaking the tap is the hard part. I took a bunch of photos of the steps I took to make the round bar cutter and will post this as soon as I have time to put it together.

Re: #1 hunter tool in new holders

#18

Re: 35 degrees?

john lucas

>I pretty much hold it at the same angle for either rough cutting which is about 35 to 45 degrees or final cutting which I have found to be from 45 to 55 degrees or steeper. I start with the tool flat on the tool rest which gives me 35 degrees and then tilt the cutter CCW until I get the cutting action I want. 35 is right for quick removeal of wood with minimal tearout. If you want really clean cuts then tilt it CCW even more and slow down the feed rate. I can get cuts clean enough to sand with 220 or not sand at all. The main reason I have to sand it this isn't a bevel rubbing tool (at least not completely) so any hand or body movements can create a tool mark (not a tear out). This leaves a slight ridge that may need to be sanded depending on your skill and the final result needed.

Re: #1 hunter tool in new holders

#19

Re: handmade tool

Doug Thompson near Cleveland

>That is a style of insert, I'm sure Mike did the research to find out what works the best. The steel needs some kind of coating to prevent rust so your finish is perfect.

Your new tools are very well done... Good Job!

Re: #1 hunter tool in new holders

#20

Great, informative work, John! *LINK*

Eddie Pacheco: San Jose, Ca.

>Those pictures tell more than a thousand words. Very informative post and that's some nice handywork that you did. I'm sure you're going to start a Hunter tool insert ordering stampede. Is it also possible to use the ceramic inserts that are typically used in machine shops? These mostly come in triangular shapes, but the edge grind looks the same.


Ceramic cutter insert

Re: #1 hunter tool in new holders

#21

more like this  *LINK*

Ron in Drums PA

>


Round Insert

Re: #1 hunter tool in new holders

#22

RCMT

Mark Mandell - Gone Round In Jersey

>Royal Canadian Mounted Turners. It's a group whose members have taken Ellsworth's turning style to the extreme in that their lathes are all fitted with saddles. There is a further off-shoot of the group that is very much into collaborations, but we won't go there on the Family Channel.

mm

Re: #1 hunter tool in new holders

#23

Re: RCMT

john lucas

>Wow I can put hooks and lanyard on all my turning tools so they will hang from my shoulder and I can't drop them while riding the lathe. And do we get to wear those cool red outfits. :)

Re: #1 hunter tool in new holders

#24

Re: You can buy the star screw (Torx) at Lowes or

john lucas

>For the bigger ones maybe, T7 for the small cutters.

Re: #1 hunter tool in new holders

#25

Re: Great, informative work, John!

john lucas

>Eddie The edge grinds aren't the same. The cutters mike sells have a deeper depression in the middle and what appears to be a much sharper cutting angle. I've tried the inserts you linked because I have some of those with my metal tools. They don't work worth a darn, more of a scraping action on wood. Mikes cutters, cut, and leave a smooth finish.