Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Help hollowing a bowl

Posts

Help hollowing a bowl

#1

Help hollowing a bowl

Wayne Leach-NW Ontario

>Hi All,

I began making a birch bowl for my wife for a Chinese auction at her dog show but ran into problems when I got to the inside.

I turned the bowl a shape that I can't hollow using bowl gouges so I made a crude (test) tool using a 3/4" square bar and 1/4" metal turning bit installed as shown in photo. I have never seen one of these in operation and only in my "wish" catalogues.

How does one shape the bit for proper cutting or are these strickly for scraping. It would be nice to get the finish inside to reduce the amount of sanding needed? Any light you can shed on this would be very much appreciated.

I will also put a pic of the bowl up showing what I have so far!

Thanks a bunch to all.

Wayne


img

Re: Help hollowing a bowl

#2

Re: Help hollowing a bowl-bowl pic

Wayne Leach-NW Ontario

>Here is the bowl I am working on.

Wayne


img

Re: Help hollowing a bowl

#3

Re: Help hollowing a bowl-bowl pic

john lucas

>Wayne What you really need is a thick round nose scraper. You will have to be careful with that tool. The trick to using that style scraper is to take very light cuts, at least for final shaping. Keep the tool at or slightly above center. If you cut below center and get a catch it will pull the tool deeper. Above center the tool will get kicked into space. Support it as close as possible with the tool rest. Lyle Jamieson talks about how that tool cuts in the latest issue of Woodturning Design.

What you should do is regrind your bowl gouge to a steeper angle on the nose. This will let you cut toward the bottom. You might also be able to get there by rotating the flute so it points more toward 12 oclock. I usually cut with the flute at about 2 oclock but you can often keep the bevel rubbing by rotating the flute up toward 12.

Another possibility is to use the gouge like a scraper. Rotate the flute to the 9 oclock position and cut with the bottom lip. Keep the top lip really close to the wood. This is similar to what we call shear scraping. I use this cut to hollow boxes. Again keep the tool rest as close as possible.

Hope that helps.

Re: Help hollowing a bowl

#4

Re: Help hollowing a bowl

Jim Pugh, Elyria, OH

>Generally the tip of the tool is ground in a fingernail shape, similar to what you have but a little smoother. Also, you need to grind a 5 to 10� relief angle from top to bottom on the tool so it doesn't rub while cutting. You typically present the tool at about an 8 o'clock position (below the horizontal center line) and bring it up gradually until it cuts. You apparently have figured that out just fine. Also, these tools don't cut smoothly but you can gently pull the tool from the bottom along the side to knock off the high points of the ridges.

Re: Help hollowing a bowl

#5

Re: Help hollowing a bowl

Ken Grunke from SW WI

>Wayne, the tool I like to use in that situations is a curved shear scraper. It's a round beveled disc set at an angle to the work. I used a 5/8" mild steel shaft for the shank, with the end cut at about a 60 degree angle. A hole was drilled and tapped perpendicular to that angled face, about at center but a bit away from the end, for a clamp screw. 10-24 I think it is. I cut a piece from a HSS planer blade, ground it into an egg shape and drilled a hole in the center with a 3/16" glass drill. The cutter is beveled all around at about 60 degrees. I sharpen it by rubbing the top face on a whetstone so I don't even have to grind the bevel hardly ever.

It's used in a pulling motion, from the widest ID in the bowl to the rim. It will actually pull out a good shaving curl, you can rub the bevel just like a gouge.


img

Re: Help hollowing a bowl

#6

Re: Help hollowing a bowl-bowl pic

Wayne Leach-NW Ontario

>John,

Thanks for the insights!

I do not have a heavy round nose scraper YET!!!

I use P&N bowl gouges and they are indeed ground pretty steep-I will play with the orientation you suggest tomorrow.

Thanks for the valuable information.

Wayne

Re: Help hollowing a bowl

#7

Re: Help hollowing a bowl

Wayne Leach-NW Ontario

>Ken,

I really like the tool you showed here and will make something similar as soon as I can. It looks like it should yield a smooth cut.

Thanks for the input.

Wayne

Re: Help hollowing a bowl

#8

Re: Help hollowing a bowl

Wayne Leach-NW Ontario

>Jim,

Thanks for the input, I will clean up the profile tomorrow and yes the relief angle is about 10 degrees. I will experiment more with tool orientation.

Thanks for taking the time to help with suggestions.

Wayne

Re: Help hollowing a bowl

#9

Roger in MO

Re: Help hollowing a bowl

Roger in MO

>I use something similiar. Saw/file a 1/8 wide slot in the end of a 1/2 steel bar. Break off a section of planer blade and insert in this slot. Braze in place. Grind a radius on the end and side of the blade.

I have also bent the end of the rod about 10 or 15 degrees in order to get in closer to the neck.

Keep experimenting. Roger