Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Still Stuck Face Plate!

Posts

Re: Still Stuck Face Plate!

#26

Re: Still Stuck Face Plate!

Wilford Bickel

>Ruth,

Do you remember what you were doing last on the lathe before this faceplate got stuck. I am wondering if you got some CA or finish between the threads and face plate. If you did something like acetone sprayed into and on the faceplate would soften this up and help break it free. Remember - no heat or fire if you try the acetone! Otherwise - you are going to have to get rough with it and really give it some solid raps to get it to break free. You may be able to lock the spindle using a small pipe wrench letting it "lock" when it makes contact with the side wall of the housing. This may be better than putting too much pressure on your spindle lock. Get mean with it and good luck!!

Re: Still Stuck Face Plate!

#27

Re: Still Stuck Face Plate!

Curly Smith

>If you still haven't freed the General from faceplate captivity then try a slight modification of what others have suggested.

I can lift more than I can pull. The amount of force that I can exert pulling is limited by my body weight, the amount of force that I can exert lifting is limited by my strength.

So, with that in mind, move to the other side of the lathe with your wrench and cheater pipe. Angle the cheater pipe so that the end is about knee-level. Lock the spindle, maintain a slight upward pressure to keep the spindle locked as you move to the end of the cheater pipe. Then, grab the end of the pipe (knees bent slightly, arms locked straight, back straight) and lift.

Lifting has two other advantages over pulling in this case - you won't hit yourself in the face with the wrench when the faceplate comes free and the wrench is less likely to slip since you won't be jerking on it (lifting is a more constant pressure).

Also - if you don't mind marring the finish on the spindle you can lock it with a pipe wrench braced against the frame. Wrapping the spindle with cloth should reduce the damage the wrench will do

Re: Still Stuck Face Plate!

#28

Re: Still Stuck Face Plate!

CCollier, Pasadena, Tx

>This may sound a little weird but it works. Try drizzling some white vinegar on the joint between the face plate and the spindle, let it soak for a few minutes and then use a wrench on the nut on the back side of the face plate. I have used a small clamp to hold the pin in place on the spindle lock. Good luck.

Re: Still Stuck Face Plate!

#29

Enquiring Minds want to know....Did you get it?

Barry Irby

>Have you gotten it off?

Do be careful. I'm sure you know, but many of our suggestions include plenty of opportunities for busted knuckles and worse.

What I think is going to work is locking the shaft and using a large wrench, combined with some form of impact, that is yanking it violently or whacking it with a hammer. At the instant it turns loose, it will be completely loose and I am concerned the demons will be upon you at that point. Be careful. Do not yank it toward yourself. I think I would put my weigh on the wrench and strike it downward toward the floor, with a plan that the wrench and cheater will fall away when it breaks loose. All you need is movement between the faceplate and the shaft. If you can get the first couple of degrees, the rest should be easy.

PS,

Had a friend who put his car up on ramps and slide under it to give a bolt a mighty tug. He was lying on his back. The wrench slipped and hit almost between the eyes and knocked him out. All we heard was a sort of UHHH! Sound and he stopped talking. There he was, unconscious with a trickle of blood on his face. (Seems a lot funnier now than it did then.)

Don�t make us come over there and pick you up.

Re: Still Stuck Face Plate!

#30

Re: Enquiring Minds want to know....Did you get it

nailed_nailer

>Ruth,

I frequently use a penetrating fluid named PB blaster. It should be available in any Autoparts store. The stuff works great on rust. Caution....it also eats paint so watch where you spray it.

Just out of curosity.....and having done similar things myself in the past.....you are trying to remove the faceplate in the counterclockwise direction right? I broke a 12 point 9/16" wrench trying to beat off a brake bolt on my truck last year. I was tightening it instead of loosening. :-)

Good Luck,

---Nailer---

Re: Still Stuck Face Plate!

#31

Leo Van Der Loo

Re: Sorry Ruth, Ive been having fun (turners club)

Leo Van Der Loo

>Hi Tom, this heating part was a respond to a couple of earlier offered ideas to heat things up.

My opinion is also to stay away from heating, I put in the reasons why I don't think, doing something like that with the typical home shop equipment would be a good idea.

Mind you, I have in my professional life heated parts or flame cut stuck parts to get them off, the right equipment and knowledge are there to do these things, if all else fails, but it is a (don't try this at home) thing.

Have fun and take care

Leo Van Der Loo

Re: Still Stuck Face Plate!

#32

Re: Still Stuck Face Plate!

Bill Hale / The Wood Spinner

>Ruth

If you have dry ice available pack the shaft with it and allow time for it to freeze. After it is frozen, then use a tourch on the face plate to get it quite hot. Do this heating fast so the shaft does not warm. Between the shaft shrinking and the face plate expanding you should be able to remove it with a 24 in. pipe wrench. set up the pipe wrench, press the locking pin and heave ho. Be sure not to have your fingers where they will crash into the lathe if it frees.

Some years back one of the foreign cars had a bearing that had to be removed this way.

Good luck, Bill

Casa Grande, AZ.

Re: Still Stuck Face Plate!

#33

Keith Tompkins

Re: Still Stuck Face Plate!

keith tompkins

>Ruth, Yes, that's the spindle lock. It's spring loaded to prevent starting the lathe with the pin pushed in. Try this...try to find an assistant to hold the pin in. Then, use the wrench that came with the lathe. Place the wrench in a horizontal position, whack it with a (preferrably) brass hammer. To be sure, the wrench handle should be on the spindle lock side, then tap the handle down. ( as crazy as this sounds, I've seen people work in the wrong direction, probably out of frustration). It should come off rather easily.

Re: Still Stuck Face Plate!

#34

Somebody drive over and help

Doug Thompson near Cleveland

>This has been going on too long. Lock the spindle or use a clamp to hold the spindle in place. Grab the faceplate with a pipe wrench then give a good solid hit.

Remember, a thread is nothing more than a wedge wraped around a cylinder.

Re: Still Stuck Face Plate!

#35

Hate to say this but you need a man!

Mike Brazeau

>Ruth - after looking at all these responses - I think you need a man's strength with an extension on a pipe wrench as suggested by others. You hold the button in for the spindle lock. Wally took the words out of my mouth too, I was thinking exactly the same thing. Good luck - Mike

Re: Still Stuck Face Plate!

#36

Yep, I could really stick that faceplate!!

Curly Smith

>I have no doubt that Ruth is just as strong as I am. Her task doesn't take strength, it takes force. Those of us without knuckle-dragging strength use force multipliers called machines. Ruth will use a simple machine to free the faceplate, that simple machine is called a lever.

You'd best hope Archimedes is busy or he might just rock your world.

In a battle of brains versus brawn, brains win every time.

Re: Still Stuck Face Plate!

#37

Use a small C clamp to hold button in,

Eddie Pacheco, San Jose, Ca.

>Or a large clamp to span the casting to hold the pin in. Then like the others suggest, use a pipe wrench and cheater bar to grab the hex portion.

Re: Still Stuck Face Plate!

#38

Re: Enquiring Minds want to know....Did you get it

Molly Winton

>Ruth, Larry says, "Didn't your mother ever tell you if you stick your tongue out too long your faceplate will stick like that?"

Re: Still Stuck Face Plate!

#39

Completely new Idea!

Barry Irby

>Stuck face plate? No problem. Buy another lathe. Some of us have two bandsaw. Many of the flat workers have multiple routers. Lots of turners have more than one lathe. Just dedicate this one to turning stuff on that faceplate and get another lathe for each faceplate or spindle you need to turn. There. Problem solved. No one got hurt. Not even a busted knuckle. You're welcome. Don't even send a card.

Re: Still Stuck Face Plate!

#40

Great idea Eddie.

Jennifer@Indy.USA

>

Re: Still Stuck Face Plate!

#41

The supense is killing me.

Ken Grunke from SW WI

>Is anyone else wondering, or is it just me?

Ruth, did ya get that sucker off? Didja get it, eh? Didja, didja getit, didja??