Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Still Stuck Face Plate!

Posts

Still Stuck Face Plate!

#1

Still Stuck Face Plate!

Ruth Niles

>Sorry about not responding to all the help offered, I was busy trying everything.

As you can see in the picture, there are no threads showing to oil or grab.

Leo, your idea is great but it's the small face plate and I can't get to the holes, I tried just screwing a 2X4 on the outside but the screws didn't hold. Thanks for the compliment on my new website, your stoppers look great in a frame!

Bill, a few questions I didn't quite understand; are you referring to that big pin on toward the front of the lathe? If so, how do I hold it in? I jammed a wrench in the notch on the wheel so the spindle didn't turn. Is there a secret to locking that pin in? Also you said the handwheel is LH threads and to put that on and turn the face plate loose; put it on what?

Curly, if that #%*&!@ face plate doesn't come off in the morning, you can bury it or cremate the lathe and the face plate!


img

Re: Still Stuck Face Plate!

#2

Re: Still Stuck Face Plate!

Jennifer@Indy.USA

>Ruth can you drill holes in a 2x4, or any board, to match the pattern on the face plate then use threaded bolts and nuts to hold it to the face plate...and then whack it? They'd need to be fairly skinny bolts, but at least they'd be held in there in order to be able to whack it good!

What a PITA!

Re: Still Stuck Face Plate!

#3

Re: Still Stuck Face Plate!

Ken Grunke from SW WI

>Ruth, one thing to try is heating the faceplate with a torch to expand it, and loosen it's grip on the spindle nose. Doesn't have to be red hot, or even glow, so a standard propane torch would be better than nothing. Heating it up will also help to wick WD-40 or equiv. into the joint where the faceplate butts up against the lathe's spindle nose.

Is that pin spring-loaded, or can you just push it into the slot?

Looks like you just need a wrench to fit on that hex of the faceplate, and with a handle extension for leverage. Beg, borrow or buy a pipe wrench to fit the faceplate, and find a piece of iron pipe to fit over the handle for leverage, 3 to 6 ft long. It would have to be a fairly big wrench, maybe you can rent one--2-3 feet long. Align it in a position where the end is about a foot off the floor, and PUT YOUR FOOT DOWN on it. Round up a helper, to help hold the wrench on (or stand on it) and for moral support. It's GOTTA come off!

Re: Still Stuck Face Plate!

#4

Re: Still Stuck Face Plate!

john lucas

>Ruth That big silver thing looks like a spindle lock. doesn't that push into the big notch in the ring on that shaft. If you can lock the shaft but still can't get hold of the faceplate, what you need to find or borrow is a chain wrench, or a big pipe wrench to put on the outer portion of the faceplate.

Another possibility would be to put some steel rod or bolts into 2 of the holes in the faceplate and then put a crowbar or some such heavy metal piece inbetween the two metal rods and use that as your leverage. If they are the same size as the holes you might get by. If not they may bend.

Wish I knew more about the General so I could help you more.

Re: Still Stuck Face Plate!

#5

Re: Still Stuck Face Plate!

Ruth Niles

>I tried that, Jennifer, it didn't budge but it was very difficult getting the nuts tight against the plate and I had washers on, too.

The General may die with a face plate attached to his head!

Re: Still Stuck Face Plate!

#6

Spring Loaded

Jennifer@Indy.USA

>Yup, Ken the spindle "lock" is spring loaded. A third hand to hold the button in would be great for Ruth right about now.

Re: Still Stuck Face Plate!

#7

Re: Still Stuck Face Plate!

Jennifer@Indy.USA

>NO! He can not die!

Re: Still Stuck Face Plate!

#8

Re: Still Stuck Face Plate!

Ruth Niles

>Thanks, Ken, I'm going to try heating it first thing in the morning. I have a job of 6 big pieces and I really need that lathe! I have a pipe wrench but didn't think about a 2'-3' pipe extension, I only went out about 18". I'll let you know.

Re: Still Stuck Face Plate!

#9

Re: Still Stuck Face Plate!

Ruth Niles

>Thanks, John. I do have a big crow bar, only problem is with the small face plate, the holes aren't large enough to take a bolt of substantial size. Right now I'll cut the face plate in 1/2 if need be.

Re: Still Stuck Face Plate!

#10

Biggest bummer is

Ruth Niles

>Right after the SSS in GA this past weekend, I took an "efficiency in productivity" class with Nick Cook. That man is a regular Turning Machine! So he showed me all sorts of quick methods, tips, jigs and different grinds on old tools, I got home Tues. evening, went out in the shop early Wed. morning to do a job that I promised would be in this morning's mail. With the day at Nick's in mind, I was going to get this job done in no time, step 1, wood on face plate....... never did get to step 2! So much for "efficiency in productivity" in my shop. And don't anybody tell Nick!!!!

Re: Still Stuck Face Plate!

#11

Dennis in Southern Oregon

Re: Still Stuck Face Plate!

Dennis in Southern Oregon

>Ruth,

If you are willing to sacrifice the faceplate, ream two or more of the existing holes to take a 5/16 or larger bolt and use 5/16 bolts to bolt a 2x4 or angle-iron lever to the faceplate. If necessary,squirt penetrating oil (designed for this job) into the joint and heat the faceplate with a propane torch. Dennis

Re: Still Stuck Face Plate!

#12

Re: Still Stuck Face Plate!

adrien

>Ruth, assuming you can lock the spindle as before, it would appear that the face plate has a hex nut at the back that could be held by a wrench, or failing one large enough, by a pair of channellock pliers or even a pipe wrench. The latter won't make the hex nut very pretty, but it would work.

Re: Still Stuck Face Plate!

#13

Re: Still Stuck Face Plate!

Wally Dickerman in Arizona

>Junk it Ruth....get a Oneway

Wally

Re: Still Stuck Face Plate!

#14

Leverage

Jim Shaver - Oakville, Ontario

>Hi Ruth,

You need to get leverage on the problem�..you can get a pipe wrench, and a long pipe with a diameter that will fit over the end of the wrench. Get it on the face plate nut, some one holds in the spring loaded spindle lock and heave on the pipe over the end of the wrench��

Take care,

Jim

Re: Still Stuck Face Plate!

#15

Re: Still Stuck Face Plate!

E.T.

>I hold the shaft lock pin in the slot by wedging a small piece of wood (clothes pin) between the cotter pin (can't be seen in the photo) and the cast iron headstock.

Actually, the cotter pin could be removed, the pin withdrawn and the spring removed. Then re-insert the pin into the hole, engage the slot and it will stay in place, no extra hands required.

This lathe comes with a substantial cast iron faceplate removal tool (wrench), that will withstand a substantial smack with a 3 pound hammer or a gentle pull with a 3 foot pipe on the wrench.

Apply penetrating oil or WD 40 to the hole at the front of the faceplate, where the spindle and faceplate threads emerge. ET

Re: Still Stuck Face Plate!

#16

Re: Still Stuck Face Plate!

Barry Irby

>If the General face plate locks up against the spindle nose or end of the spindle that is furthest inside the faceplate, you need to apply penetrating oil to that spot. I would install a chuck on my tail stock and put a bit in it and use it to drill through the face plate into the hollow shaft. Then I would put some Penetrating oil like PB Blast in through the hole and let it soak. Or you might be able to shoot it into that area through the hollow shaft.

I would use the shaft lock or a pipe wrench on the shaft and a huge pipe wrench on the face plate and a pipe on the handle. If I did not have a pipe wrench I might try sanding the face of the face plate bright and clean and gluing a long piece of steel across the face plate with epoxy and using it as a wrench to unscrew the face plate. Once I broke it free, I would heat the metal with a torch or heat gun to release the epoxy. If you drill the hole tonight and add the penetrating oil you can let it soak while the epoxy sets.

I might also try locking the shaft on the lathe and filing a notch in the rim of the faceplate. Then I would set a cold chisel in the notch and give it a really sharp rap with a hammer to break the Faceplate loose.

Re: Still Stuck Face Plate!

#17

Why not

Bill Howatt

>IF you put the wrench on the hex part of the faceplate and push the spring-loaded locking pin into the groove you can pull on the wrench enough to cause the pin to stay in the groove. If that doesn't work then put a piece of wood between the headstock and the cotter pin to hold the pin in the groove on the spindle. Pull on the wrench to loosen the plate and if it doesn't give it a sharp rap with a hammer. If that doesn't work put a wrench with a longer handle on the hex part of the faceplate.

Bill

Re: Still Stuck Face Plate!

#18

Re: Still Stuck Face Plate!

E.T.

>No need to drill hole into faceplate. the General FP's are open all the way through.

How about heating up the faceplate with a heat gun instead of a torch, then trying the wrench. Heat should cause the CI to expand a little. I used to disassemble rusted and corroded brake lines and bleaders by heating them with a torch and was always amazed the way the little nuts came loose with the heat. ET

Re: Still Stuck Face Plate!

#19

Many good ideas, JUST DON'T HURT YOURSELF+a little

Ken Grunke from SW WI

>pep talk...

Ruth, the pipe wrench idea seems to be a popular one but if you have the wrench that ET says comes with the lathe, use it. A pipe wrench can fly off if not seated just right, causing various types of possible bodily harm. The idea of removing the spring from the lock pin sounds great also. I have been in many similar frustrating circumstances and mind always wins over matter as long as you keep your head (and use it also). I don't know you personally, but I'm convinced you are a level-headed person of above average intelligence and that you will prevail over mere molecules of stubborn cast iron which have not one iota of conciousness or intelligence. I wish you all the luck I can possibly muster from so many miles away. Go get'em, girl!

Re: Still Stuck Face Plate!

#20

Re: Still Stuck Face Plate!

Tom Storey

>Ruth, that looks like my lathe. The pin is spring-loaded as you know but once you put some torque on the face plate nut, the pin should stay in place. Put a crescent wrench on the face plate nut (or the wrench that came with the lathe), add an extension handle (3/4" galvanized pipe?) of about 3 feet. Engage the pin, start to pull on the extension, release the pin as it should now stay in place, come onto the extension with VIGOR and maybe a bit more! You may have to take a dead-blow hammer to the extension to 'coax it free'. But free it will come!

Re: Still Stuck Face Plate!

#21

Leo Van Der Loo

Sorry Ruth, Ive been having fun (turners club)

Leo Van Der Loo

>and only now saw your post, to bad the wood lever didn't work, yes it is a small faceplate.

But what now, I can see the slot for the lock to go in and also the button, and my next move would be to get a clamp or use something else like a small block and string to hold the lock button in, then get the Generals face plate wrench onto the face plate and a good sized hammer and WHACK that wrench a time or two, that should do it, an impact will do more than a steady pull.

If that doesn't work you'll need professional help, and maybe even cut the face plate.

You could try heat, but a propane torch just doesn't give enough heat quick enough to expand the faceplate, and will heat the shaft just as fast as the faceplate and also the bearings.

Not only that, but the faceplate is not stuck to the shafts diameter but against the shoulder, heating the faceplate would just get it tighter I would expect, though after cooling down it might come loose, that does happen.

If I lived closer I'd be over to give you a hand, now I just hope you will be able to do it by yourself, good luck Ruth

Have fun and take good care

Leo Van Der Loo

Re: Still Stuck Face Plate!

#22

Re: Sorry Ruth, Ive been having fun (turners club)

Tom Storey

>Good Lord! Keep the heat away from your lathe!!. Christmas!! Don't make a bad thing worse! Like I said, engage the pin, come onto he damn face plate nut as hard as you must to make it do whatever you want it to do. I cannot see this as a requirement, but...a drop or two of penetrating oil will help. Don't hurt your lathe!

Tom

Re: Still Stuck Face Plate!

#23

I feel your pain...

Jorge Castaneda

>Ruth,

Here is a pic, not from s stuck face plate, but from a stock quill that crippled my lathe for a couple days, here is what I used to undo the problem:

Once I had that wrench firmly attached, I did whack on it with a rubber mallet.

Another solution that comes to mind is to drill a hole in the faceplate if it does not have one already, let's say a 5/16" or 3/8" as deep as you can, 3/8" or 1/2" is plenty, and then use a bar of that diameter as a lever to yank with.

Hope this helps

Good luck

Jorge


img

Re: Still Stuck Face Plate!

#24

Dick Hines

Re: Still Stuck Face Plate!

Dick Hines

>Ruth, I have not read all the post but if someone has not said anything about heating the face plate you give that a try. Not red hot just toasty warm.

Good luck.

PS. I will be at a show this weekend so if you want to you can use my lathe.

Re: Still Stuck Face Plate!

#25

Re: Still Stuck Face Plate!

Charles B. Watson

>On my old General, I could press the locking pin into the slot and keep it in the slot by holding pressure such as by using the faceplate wrench and pulling down (counter clockwise). This would free up one hand to hold the wrench in place and use the other to tap the wrench with a deadblow hammer. Liquid Wrench sprayed at both ends of the faceplate as close to the threads as possible would help, too.