Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Motor upgrade, pulley needed?

Posts

Motor upgrade, pulley needed?

#1

Motor upgrade, pulley needed?

Leppikallio

>If I remember correctly several persons around here has replaced motor from their lathe. I got new motor and controller for my lathe. However I don't know where to get proper pulley for this new motor.

My lathe is basically delta midi (in fact it is Fox brand lathe but it should be basically same lathe as delta midi). It has that "multi rib" belt and pulleys. Old motor has 14mm shaft, new motor has 19 (perhaps 3/4") shaft. There is not enough room in old pulley for bigger bore. Pulley in lathe side has 19mm / 3/4" bore also but keyway is too small so it wouldn't fit even if I were able to get one from somewhere.

All friendly machinists around has promised to make new pulley for me but when they notice/hear there should be keyway also they say "no way" and I don't have pulley. Does someone have good ideas? Is there some online store which could have these multirib pulleys in their catalog?

Re: Motor upgrade, pulley needed?

#2

MSC *LINK*

Mike Cunningham (Cape May)

>A friend turned me on to MSC and I got one there for an old Delta. Do a search at the link.

Mike


MSC Big Book

Re: Motor upgrade, pulley needed?

#3

Leo Van Der Loo

Re: Motor upgrade, pulley needed?

Leo Van Der Loo

>First question I have, why do you need a keyway ?, seems a setscrew would hold well in the motor shaft keyway, I assume there is one, that way you could use the lathe spindle type pulley.

You could also pull the armature from the motor, and have it turned down to a size that you can accommodate in your motor pulley, maybe 5/8"/16mm is possible.

Have fun and take care

Leo Van Der Loo

Re: Motor upgrade, pulley needed?

#4

Re: Motor upgrade, pulley needed?

John Lucas

>How many steps in the pulley and how big is the outside. I have one I pulled of my jet mini that has 3 steps. It uses setscrews. I would have to measure it to see the shaft size but somewhere around 3/4 sounds like it might be close. Could be 5/8" I haven't looked at it in a while.

Re: Motor upgrade, pulley needed?

#5

Roger in MO

Re: Motor upgrade, pulley needed?

Roger in MO

>You might try www.grainger.com. They have a wide variety of sheaves and probably would have it machined to your specs. If they won't sell retail (some stores won't) they probably can point you to a distributor.

Re: Motor upgrade, pulley needed?

#6

Re: Motor upgrade, pulley needed?

Leppikallio

>This is current pulley, spindle side. Each step is 8.5mm (0.3346") wide, 2mm (0.07874") from bottom of groove to bottom of groove. Motor shaft is 19mm (0.748") diameter.

Diameter of the new pulley is not that critical because new motor is controlled with frequence converter anyway.

Re: Motor upgrade, pulley needed?

#7

Re: Motor upgrade, pulley needed? 

Leppikallio

>


img

Re: Motor upgrade, pulley needed?

#8

Re: Motor upgrade, pulley needed?

Brian Hahn in SW Wisconsin

>My experience has been that the smaller multi-rib belts used on lathes are usually automotive or recreational (sport) vehicle design. At least when I wanted a different size belt for my lathe, I finally ended up at a local automotive parts store and they had a variety of sizes in stock.

So, you might check the automotive and sport vehicle suppliers. I checked my normal industrial supply source (McMaster-Carr) and came up empty.

Re: Motor upgrade, pulley needed?

#9

Re: Motor upgrade, pulley needed?

Danny Wells

>When I got a pulley for a new motor on my Jet Mini, Craft Supplies had some pulleys for the Vicmarc mini that worked, same steps. But it had enough metal that it could be bored out for the new shaft size.

Gates makes a ribbed belt that has 6 ribs. It is the J-series belt. It has the exact same rib width and configuration so it is just twice as wide as the belts used on the mini lathes. I bought one and just cut it in half, so I ended up with two belts with 3 ribs, works great. You can get them at most industrial supply outfits.