Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Bonehead Award for the Week .........

Posts

Re: Bonehead Award for the Week .........

#26

Re: Multifunctional Applications

Bruce Wiseman

>I thought this was everyday wear up north, eh. :-)

Re: Bonehead Award for the Week .........

#27

Re: I'm seriously considering a chain saw helmet.

Stuart Johnson

>Would there be enough room for dust mask? I use a 3-M half mask under my regular cheap face mask.

Re: Bonehead Award for the Week .........

#28

Re: Bonehead Award for the Week .........

ken

>I have only been turnig for a little over a yr,but have been using safety shields for more than 40.I know they are a pain sometimes to keep clean,but it only takes a min.to wipe of the face when it starts getting dusty.I use compressed air,but its better than using a white cain and yes those pesky little particals can and will sneak right around small safety glasses.I allways wear a full shield and have been conked a few times,but other than an underwear change,no harm done.As for the type of shield, I get mine for about 10 bucks each and they hold up great.Sorry about the safety lecture,but I have seen to many folks hurt by taking short cuts.

Re: Bonehead Award for the Week .........

#29

Re: I'm seriously considering a chain saw helmet.

ken

>Yes there is plenty of room for a dust mask,but why get a chainsaw helment for turning?seems like an overkill as a full face shield would work just as well,plus it would keep the dust away from your face much better and is a lot cheaper.When using a chainsaw though it is a different story.Don't start the saw without one.

Ken

Re: Bonehead Award for the Week .........

#30

Re: I'm seriously considering a chain saw helmet.

Mark Kauder, Phenix City, AL

>The point on the Chainsaw Helmet, was you did not have the issures with fogging, and stuffy air you get with a shield.

BTW, Face Shields do Zero for keeping dust away from your nose/mouth.

Mark

Re: Bonehead Award for the Week .........

#31

Re: Multifunctional Applications

Jim Shaver - Oakville, Ontario

>Shhh, Bruce.....you'll give away all our secrets...eh!

:-)

take care,

Jim

Re: Bonehead Award for the Week .........

#32

Missing the Point..

Mark Mandell - Gone Round In Jersey

>Rule No. 1 [in woodturning and Kendo): DO NOT OFFER YOUR HEAD (face, etc.) AS A TARGET!!

If you encase your head in thermo-plastic and steel bars, the schrapnel will hit you square in the clavical, neck, jewels, or OVS (Other Vital Spot) so long as you persist in standing in the LOF [Line Of Fire]. There is just no cut (that I have heard of) that requires you to do whilst looking at that spinning piece of wood "edge-on."

The physics of the lathe are not complex, guys. Take the distance between centers (or thickness of piece) and extend that area 90* from the lather bed. Stand in that zone and you get to wear the "target" T-shirt. If, however, you keep the tool rest between you and the wood and your various body parts to one side or the other and out of plane of rotation of the workpiece, you may marvel at how far the pieces got thrown, but not at how badly you got hurt by them, since they will have wizzed by you on their way to the far wall.

[YES, I always, ALL WAYS, wear my face shield, even when sanding.]

Heal fast. Confession is good for the soul.

mm

Re: Bonehead Award for the Week .........

#33

Keith Tompkins

Re: Bonehead Award for the Week .........

keith tompkins

>Jen, I'm not too concerned about the safety stuff....but the fountain of youth face cream has picqued my interest!

Re: Bonehead Award for the Week .........

#34

Perhaps you could enlighten me.

Brian Hahn in SW Wisconsin

>How do I stand out of the line of fire when turning the middle of a 36" long spindle?

Re: Bonehead Award for the Week .........

#35

Re: I'm seriously considering a chain saw helmet.

ken

>I have a fan in back of me,plus I have the full facemask on with a good quality dust mask on.Also I have a dusk collector system hooked up and I don't have any problem with the dust or stuffiness.I was doing it this way long before I got the dust collector,that was just a little extra protection and it was a great investment.Just tryin to offer a little safety advice.The best this is the airsheld,that is coming this year.

Ken

Re: Bonehead Award for the Week .........

#36

Re: Perhaps you could enlighten me.

Mark Kauder, Phenix City, AL

>Brian,

The problem is seldom with spindle. By their very nature, they are captured between centers.

Bowls should be when roughing, but are not always.

Mark

Re: Bonehead Award for the Week .........

#37

Spindles

Mark Mandell - Gone Round In Jersey

>Had several come apart on me. Every time they merely dropped to the floor as they don't have the wide diameter mass that imparts the dangerous centrifugal force 1 or 2 feet out from the center line. The example was a platter or bowl form that disintegrated.