Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Polyurethane glue

Posts

Polyurethane glue

#1

Polyurethane glue

Bill Crommett

>I am doing a staved piece that will be exposed to the weather, so it must be done with polyurethane glue. Has anyone had any experience with some kind of slippery stuff that won't stick to polyurethane glue ?. I need somwething to protect my form from being part of my work piece.

Re: Polyurethane glue

#2

Re: Polyurethane glue

John Lucas

>Bill I've used Johnsons paste wax to protect my workbench or clamping forms when clamping segmented work and using either epoxy or polyeurethane glue.

Re: Polyurethane glue

#3

Re: Polyurethane glue

Stuart Johnson

>Would wrapping the form in plastic wrap or wax paper do it? It would be easy enough to check.

Re: Polyurethane glue

#4

Re: Polyurethane glue

Bill Crommett

>John: Good thought. I was thinking along the line of something in sheets, never considered wax. Thanks

Bill

Re: Polyurethane glue

#5

Re: Polyurethane glue

John Lucas

>Bill I forgot I also use wax paper sometimes. The problem with wax paper is it's easy to get a krinkle that gets caught between a segment. It's really good for some things and really bad for others.

Melamine covered hardboard also works well.

Re: Polyurethane glue

#6

Re: Polyurethane glue

Mark Mandell - Gone Round In Jersey

>Bill,

If it's true waterresistence you seek, consider TB III. Has the same waterproof rating as the poly, but not the history of joint failure. I quit using the monkey stuff after a number of joints in flatwork failed after full year's seasonal changes. Stuff is ok where you've got precisely matching joints, but any small gaps are broken joints waiting to happen.

A good coat of pastewax with be effective in either case. Don't buff the waxed form (leave as much wax in place as you can) and any that transfers to your workpiece will wash right off with naptha after the glue has set.

If you're really concerned about a release agent, put on the wax and then apply several coats one of one of the commercial mold release agents like poly vinyl alcohol.

mm

Re: Polyurethane glue

#7

Re: Polyurethane glue

Barry Irby

>If you are looking for a sheet product, polyethylene will work. Neither TBIII or Gorilla Glue will stick to it. Get 6 mill stuff to help keep it form slithering into joints. You can get even thicker piece by using Poly Cutting boards or even sheets of the UHMW stuff. You can also wrap things with clear packing tape and it will work until it wears out.

Re: Polyurethane glue

#8

Re: Polyurethane glue

Bill Crommett

>Barry and Mark: Lots of good info. I didn't realize the polyurethane had joint failure problems. My experience with TB 3 is limited to non stressed work, but will try it . The packing tape is a good Idea.

Thanks fellows

Bill

Re: Polyurethane glue

#9

Re: Polyurethane glue

john lucas

>Bill I've made a lot of cutting boards with Polyeurethane and never had a failure. I quit using it because it was impossible to get off your hands. I switched to epoxy. It's easy to clean off your hands with alcohol.

Re: Polyurethane glue

#10

Re: Polyurethane glue

david

>Once had a flush panel door where the veneer at the door bottom was so torn up it looked like a major earthquake on a seismograph. In repainting the door, I was faced with wood filler and a lot of sanding to get the patch smooth enough to not telegraph through the paint job. Tried applying polyurethane glue to the tear-out area, then covered it with a piece of construction vinly ("visqueen")cut to size and clamped a piece of plywood over that. Next day the filling properties of the poly glue when it dried filled in all of the gaps and the poly-vinyl came right up leaving a smooth surface. Only had to sand the ooze-out at the bottom of the door. The face of the door was paint ready. Any wrinkles on the plastic would have been imprinted on the glue surface when it dried.

Re: Polyurethane glue

#11

Joint Failures

Mark Mandell - Gone Round In Jersey

>Were discussed on the Main Board several months ago. Seems the porosity of the cured glue joint, coupled with poly's nonpenetration of the wood, makes a strong joint only if you've got wood-to-wood contact on the joint surface.

Re: Polyurethane glue

#12

John, That's why they nemed it Gorrila.....

Barry Irby

>Glue. Your hands always end up looking like that gorrila hand on the bottle. Honesty in advertising.

Re: Polyurethane glue

#13

Keith Tompkins

Re: Joint Failures

keith tompkins

>Mark, I did my own un-scientific test a while back, glueing up boards, cutting them into sections, and then breaking the pieces against a sharp edge. Titebond joints held fine, the wood broke in each test. The Gorilla glue-joints, subjected to the same abuse, broke on the glue joint...every time. I'm told the poly isn't shock resistant.