Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Mesquite, Coccobolo, and Chechen Peppermills

Posts

Mesquite, Coccobolo, and Chechen Peppermills

#1

Mesquite, Coccobolo, and Chechen Peppermills

Dominic Greco in Richboro PA

>Hello Everyone,

Here are (3) 10" peppermills I completed over the past week. They are Mesquite, Coccobolo, and Chechen. Two of these are for a commission, while the third is most likely sold already.

All feature my "signature" coaster (actually it was my wife's idea), and are of a profile I came up with and detailed using 3d Software. I used a story stick/template to allow me to get the profiles as close as possible. But as you can see, each one has subtle difference. But the critical areas are exactly alike.

The coasters are cut from the same blank of wood so that they are grain matched. I sized them so that they are a lot like suction fit box lids. They will come away with the tiniest of a "pop". But not too much that they get carried along when you lift the peppermill off of the counter.

All of them use the same "Mr Dudley" mechanisms from Packard Woodworks, and feature the same finish. One coat of sealer followed by light sanding, followed by several coats of Danish Oil, Beall buffing, followed by a coat of Renaissance Wax.

IMHO the coccobolo was the most surprising wood to work. Since I normally used pen sized blanks, I expected a troublesome wood. In my experience, coccobolo had a tendency to crack. But here it cut beautifully! You can bet I'll turn more of that if I get the chance.

The chechen was somewhat disappointing. The wood starts off as red then becomes this brownish red as you turn. If it wasn't for the commission, I probably would have never selected this wood.

The mesquite was the most fun to turn. When I started turning this wood, I remembered why I liked it so much. It takes an edge well and smells awesome. The voids were a bit of a problem. But they ended up getting filled with ground coffee, charcoal dust, and epoxy.

I also am now hooked on the use of a 3 point tool. After I made my 3/8" version, I found I needed a smaller one. So I made a 1/4", and 1/8" version. The 1/4" is now my "go to tool" for detailing spindles. Rolling beads is now more enjoyable than ever.

Now that I have these done, I have several more to make for a local restaurant owner. But he wants Olive wood! Anyone know where I can get a couple 3" sq x 12" - 14" long olive wood blanks? :>)

Mesquite Peppermill with coaster

Mesquite Peppermill with coaster

Coccobolo Peppermill with coaster

Coccobolo Peppermill with coaster

Chechen Peppermill with coaster

Chechen Peppermill with coaster

Thanks for viewing.

See ya around,

My ugly mug


Dominic

Re: Mesquite, Coccobolo, and Chechen Peppermills

#2

Re: Mesquite, Coccobolo, and Chechen Peppermills

Ron McKinley

>Beautiful work. I like the "saucers" to keep loose pepper off the table.....Ron

Re: Mesquite, Coccobolo, and Chechen Peppermills

#3

Bob Moffett

Re: Mesquite, Coccobolo, and Chechen Peppermills

Bob Moffett

>Very nice. I think I like the first one the best. The voids add a lot to it.

Re: Mesquite, Coccobolo, and Chechen Peppermills

#4

Re: Mesquite, Coccobolo, and Chechen Peppermills

Lynn from Port Townsend

>Would you please post a picture of the 3 point tool you referred to for this relatively new turner? Thanks.

Re: Mesquite, Coccobolo, and Chechen Peppermills

#5

JL

Re: Mesquite, Coccobolo, and Chechen Peppermills

JL

>Pretty peppermills. I also like the saucers. Tough to pick out a favorite.

Olivewood? I'm sure you've tried Woodfinder already :). If they weren't of much help, Atlanta Wood Products (http://www.hardwoodweb.com/distribution/awpc.cfm) has had some in the past.

Re: Mesquite, Coccobolo, and Chechen Peppermills

#6

Re: Mesquite, Coccobolo, and Chechen Peppermills

john lucas

>Really well done Dominic. I love mesquite. don't get to turn it much. Cocobolo is one of my favorites. Never turned Chechen. I'll have to get some and give it a try.

Re: Mesquite, Coccobolo, and Chechen Peppermills

#7

Re: Mesquite, Coccobolo, and Chechen Peppermills

Jim Shaver - Oakville, Ontario

>Hi Dom,

I like them all, the shapes are very nice ....that three point tool is a great find....Mike Brazeau made one as well and demonstrated it at our club a few months ago on a Hands on Night, I was very impressed.

Great work....lovely shapes in some fine wood.

Take care,

Jim

Re: Mesquite, Coccobolo, and Chechen Peppermills

#8

Re: Mesquite, Coccobolo, and Chechen Peppermills

Don O.

>Beautiful work as usual Dom !

Re: Mesquite, Coccobolo, and Chechen Peppermills

#9

Steven Antonucci

Looking good, Dom!

steve antonucci

>Each one has a detail that I like a little bit more than the next. Overall, I think the cocobolo is my favorite because the rolled beads where you would hold it during use look like they'd be most comfortable in your hands.

As a persn with small hands, I wonder if the "grip" makes any difference? What do you think, oh Master of the Three Point tool?

:-)

Steve

Re: Mesquite, Coccobolo, and Chechen Peppermills

#10

Re: Mesquite, Coccobolo, and Chechen Peppermills

Bill Neddow

>Yes, please post a picture of the tool. It is marvelous. It planes like a skew, cuts like a bowl gouge and flies over tall buildings in a single leap! All joking aside, it is an extremely useful tool, a very ancient one, and was almost lost in the mists of time until an elderly English turner discussed it in a woodturning column he wrote for a British wood turning magazine. People rediscovered how great it was, and it is now produced commercially. Mine is made by Crown -- but it is very simple to make.

Re: Mesquite, Coccobolo, and Chechen Peppermills

#11

Awesome!

David Propst

>Hey Dom!

They are all gorgeous, but especially the mesquite.

Do the mechanisms really work well? I love really coarse ground pepper on about anything that is not frozen.

Gotta start turning again after this semester...

David

Re: Mesquite, Coccobolo, and Chechen Peppermills

#12

Hi David!

Dominic Greco in Richboro PA

>David,

Long time no see, my friend! How're doing? Thanks for the compliments!

You betcha' the mechanisms work! For the past 5 years every night at dinner my wife and I use the very first pepper mill I ever made. The mechanism functions perfectly. I also love the coarse ground pepper. Especially in soups!

See ya around,

Dominic

Re: Mesquite, Coccobolo, and Chechen Peppermills

#13

Hi Steve

Dominic Greco in Richboro PA

>Steve,

You wrote:

"As a person with small hands, I wonder if the "grip" makes any difference?"

I hear ya my friend! To make sure that I didn't make the same mistake I made some time back, I had my wife (who has small hands) try them out. She loved the fit and the balance as well.

To elaborate on the "same mistake" comment I made above, here is a short story. My Dad and I were about the same size. Both about 6' tall. The summer after my Dad retired he wanted to make a new picnic table large enough to comfortably seat most of our guests for our family gatherings. So I designed it on Autocad per his instructions. After we assembled the entire thing, we sat down at the table and congratulated ourselves on a job well done. Later when the entire family sat down for a impromptu bbq dinner, we discovered that we had made the table to fit our proportions, not everyone else's. My full grown sisters and Mom all looked like preschoolers sitting at the "grown up's" table! Needless to say, we cut the legs down appropriately the next day!

See ya around,

Dominic

Re: Mesquite, Coccobolo, and Chechen Peppermills

#14

Here ya go!

Dominic Greco in Richboro PA

>Lynn,

Here is a link to the post I wrote some time ago in which I show my Shop built 3 point tool. If you're curious about making one, I suggest looking up the article I mention in the AWA Journal. They are very easy to make and even more fun to use.

See ya around,

Dominic

Re: Mesquite, Coccobolo, and Chechen Peppermills

#15

Thank you all for your kind words

Dominic Greco in Richboro PA

>

Re: Mesquite, Coccobolo, and Chechen Peppermills

#16

Yes, I'd love some cracked pepper...

Thomas Skaggs, Foothills of Mount Level

>Suddenly I have a taste for Ceasar Salad....and yes, I'd love some cracked pepper please! All very nice but the coccobolo one is my favorite. Great job buddy!

Tom

Re: Mesquite, Coccobolo, and Chechen Peppermills

#17

Hi Jim!

Dominic Greco in Richboro PA

>Thanks Jim. I appreciate the compliment!

Re: Mesquite, Coccobolo, and Chechen Peppermills

#18

About the photos....

Dominic Greco in Richboro PA

>John,

Thanks for the compliments!

BTW, I finally got my photo booth together (it only took me a year) and used it for these photos. I was able to get the color to come out OK, but still need to eliminate the shadows and bright spots. Also, the pictures were dark and I needed to use "Gamma correction" in the photo software.

I'm using 500 watt halogen lights on either side, directed up at an angle to an overhead bounce card. On both sides are diffusing panels made up of translucent fabric. I think I need to add another light overhead.

The funny thing is that I took a photo of a small mesquite box I turned and it came out PERFECT! As soon as I replaced it with the pepper mills, the color went darker.

Small Mesquite box with lid off

Small Mesquite box with lid on

Your thoughts?

Dominic

Re: Mesquite, Coccobolo, and Chechen Peppermills

#19

Thanks Tommy!

Dominic Greco in Richboro PA

>Any time you're in the area, you're welcomed to come over for a nice big Caesar Salad with fresh ground pepper!

See ya,

Dominic

Re: Mesquite, Coccobolo, and Chechen Peppermills

#20

Re: Mesquite, Coccobolo, and Chechen Peppermills

Jennifer@Indy.USA

>Dom,

These are really awesome mills! I made a few several Christmases ago and swore I'd never do that again. I can appreciate the work that goes into them. These are beauties!

Jen

Re: Mesquite, Coccobolo, and Chechen Peppermills

#21

Chechen Warning

Harvey Meyer in Atlanta

>First let me say that these are beautiful pepper mills - well done Dom!!

Let me warn everyone about Chechen because it got me and I'll never turn it again!!

Chechen, aka black poisonwood, or Carribean Rosewood is in the same family as poison ivy, cashew, poison sumac etc. The bark oozes a black sap that contains the same nasty chemical that gives us poison ivy. The wood itself, is benign. However, sanding dust from Chechen can give you a wicked case of poison ivy or dermatitis, I learned this the hard way. I'm not sensitive to any woods - even cocobolo, but Chechen did me in when I turned a goblet from it. Interestingly, when it's sold, they don't call it black poisonwood. I guess it would be hard to sell with that name. So beware of Chechen!!!

Dom - super nice peppermills.

Harvey

Re: Mesquite, Coccobolo, and Chechen Peppermills

#22

Re: About the photos....

john lucas

>Dominic You don't need more lights just work with the two you have. Send me a photo of your setup and I'll try to make some suggestions. You don't want to eliminate all shadows and highlights. If you do the piece will look flat.

I would raise the left light or whatever is producing the highlight on the left. This will hopefully cast some soft shadows below each bead and help to add shape. It will also light the top more. Then you might move the right hand light toward the front more to help illuminate that area. If your shooting through a translucent panel on the right you might have to move this toward the camera so that light still shines though the panel. I'll be able to tell you more when I see the set up.

If you were usuing the camera in Manual mode it won't change the pieces as you change them out. If your in auto mode then everything you do will change the exposure slightly.

Re: Mesquite, Coccobolo, and Chechen Peppermills

#23

Re: Mesquite, Coccobolo, and Chechen Peppermills

Mike Rubes, Apex, NC

>Hi Dom,

Wonderful to see stuff from your shop and such GREAT stuff at that! Those are really awesome! The detail and fit and finish are top notch! Wow, those are really great! I like the little saucer to hold them as well, a very nice touch.

I hope everything is going well for you. I hope to see you again in PA at Bill's this summer.

Thanks for the pics, they really are wonderful pieces.

Mike

Spring is definitely coiled in Apex, NC, ready to go!

Re: Mesquite, Coccobolo, and Chechen Peppermills

#24

Those are great looking peppermills, Dom!

Eddie Pacheco, San Jose, Ca.

>

Re: Mesquite, Coccobolo, and Chechen Peppermills

#25

Sweat!

Ron in Drums PA

>They all look great Dom.