Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Modifications to Jet 1236

Posts

Modifications to Jet 1236

#1

Modifications to Jet 1236

Ed Larson

>Recent posts about the Jet 1236 prompted me to describe modifications I'v made to my previous owned Jet 1236. First I purchased a hand wheel from Jet and drilled a 3/8 inch hole in it to accept a knockout bar made from 1/4 inch rod. A second benifit from this modification is that when the knockout bar is inserted down through a hole in the shaft of the handwheel (this hole comes with the handwheel) and blocked against the headstock lock stop you have a spindle lock (see second picture). I also made a portable switch from a electrical box which attaches to the lathe bed with magnets (third picture). From the overall picture you can see the stand, drawers and tool holder that I made for 2 X 6 lumber and plywood. I had to raise the lathe above the original stand height to fit my 6-5 body. Questions and comments welcome.


img

Re: Modifications to Jet 1236

#2

Re: Modifications to Jet 1236 

Ed Larson

>


img

Re: Modifications to Jet 1236

#3

Re: Modifications to Jet 1236 

Ed Larson

>


img

Re: Modifications to Jet 1236

#4

Roger in MO

Re: Modifications to Jet 1236

Roger in MO

>Ed, good ideas. I only raised my 10-36 by 6 inches and find the off switch unhandy. Mine is older, the grey model. The method of attaching a hand wheel is not readily apparent. What was the interface between the wheel and shaft?

Re: Modifications to Jet 1236

#5

Re: yes, more info please

Mike Hamilton

>I have a 1236 and would love to have a headstock handwheel. I find nothing listed by WMH for this except the handwheel for the tailstock end.

Regards,

Mike Hamilton

Plainfield, IN

Re: Modifications to Jet 1236

#6

Re: Modifications to Jet 1236

Ed Larson

>The handwheel is not listed in the parts list for the Jet 1236 but Jet makes one and if you call them you can get one. You will have to drill a 3/8 inch hole for the knockout bar. The handwheel fits the threads in the outboard end of the headstock of the 1236. Do not know if this is true for the 10-36.

Re: Modifications to Jet 1236

#7

Re: Modifications to Jet 1236

Steven Smith

>I ordered a hand wheel for my 1236 from Best Wood Tools. They had a booth at the Tampa tool show a couple of years ago. I noticed that the wheel is not on their website but its a small operation and if you email them I bet they would make one for you. I think mine was about $70 but I dont remember for sure. Hand wheels make all the difference and are worth the investment.

Re: Modifications to Jet 1236

#8

Re: Modifications to Jet 1236

Ron in Drums PA

>I have a hand wheel now for a while. I never thought about drilling a hole in it. Good Idea, something I need to do.

Have you considered add a vacuum fitting to the hand wheel? I saw this on a different brand once and it worked well.

Re: Modifications to Jet 1236

#9

think this is what you need

John in Ks

>If the Jet 1236 is the lathe HF34706 copied then this should be the handwheel you need:

The part no is WMH708344 -JWL-HW.

Last time I checked it was approximately $11.90. Be sure to call and order it so shipping will be lower. If you order from them online, they overcharge on shipping with flat rate $20 charges. Not the case if you call in an order.

I have two numbers for WMH tools (Jet)

1-800-274-6846 and

1-800-274-6848. One is the general number and I believe the second is the order department.