Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Signing your work revisited

Posts

Signing your work revisited

#1

Signing your work revisited

Mike Cunningham (Cape May NJ)

>I've been using a razortip but I'm not overly pleased with the results, not a fine enough line, perhaps I'm using the wrong tip, temp or too heavy-handed. I'm looking for a pen, something other than the ultra-fine sharpie. Someone once mentioned something about archival pens, can that person or someone else give me further info on that, such as a brand name or place to purchase.

Thanks,

Mike

Re: Signing your work revisited

#2

Re: Signing your work revisited

don lewonczyk

>Hi Mike, im an uninterduced luker, but maybe I can help. I have a dozen or so different size tips, they are numbered and they all will put a line down without any pressure. It like glides on your piece. They are mostly used for drafting and you can get different colored ink for them. A drafting supply store or an art store carries them and im not sure of the spelling without going down to my shop and looking but I think Ko-Noor or close to that and they are made in Germany and run about 10 to 14 bucks each. I use mine for fine lines to enhance my carvings, works great. A drafting store may be willing to give you a demo. Hope it helps. DonL

Re: Signing your work revisited

#3

Re: Signing your work revisited

Steven

>Hi Mike. I like to use an acid free India Ink marking pen from the office supply store. They have a very fine point and the ink will not run or smear as you put a finish over them. As I recall they cost about $4.50. Steve

Re: Signing your work revisited

#4

Re: Signing your work revisited

Glenn Hodges, Nashville, GA

>Mike I sign my work using an archival pen, and have good results.

Re: Signing your work revisited

#5

Re: Signing your work revisited *LINK*

Mark Wollschlager

>I have used these with success.

Perm. Ink, pretty robust tip.

They come in a .1 mm, really fine point.

mark


Itoya Finepoint System 3

Re: Signing your work revisited

#6

Re: Signing your work revisited

David

>To clarify Don's post, he is talking about Kohinor Technical Pens, although there may be other brands available, such as K & E, Leroy, or Mars. When using these pens, make sure the ink will not bleed when dry. When left to sit for a long time, the tips of these pens will dry out and clog the ink flow. There is an internal wire element that when shaken will free up the tip if not left too long.

I use a Dremel engraver, Model 290-01. Having good writing helps ;-).

Re: Signing your work revisited

#7

Re: Signing your work revisited

Bill Luinetti

>This lurker suggests either 0.05mm COP/C MULTILINER SP or 0.1 ARTLINE. I get both of these from DICK BLICK Art Supply.

Of course, you can GOOGLE for any of that.

Bill

Re: Signing your work revisited

#8

Re: Signing your work revisited

john lucas

>Mike I've been playing with burning my name although I prefer the Dremel engraver. With either one there are two things that really help. sand the surface your writing on to at least 220. Use really light pressure. With the burning pens find a temperature that makes a fine line when you just barely touch the wood. This won't be a hot deep burn just a very fine line. I use a small tip that's rounded over. I also have a ball tip that works pretty well as long as the temperature is low enough.

The top two are dremel engraver and the bottom two are burner


img

Re: Signing your work revisited

#9

Re: Signing your work revisited

keith zimmerman, Normal IL

>Like you, I was using a Sharpie with less than spectacular results. I found that buffing removes the ink and you can't write on carnuba wax. Also, to me, it seems as though wrinting on the bottom appears to be an afterthought and can look amatuerish. That's probably in my own mind, but that's my thinking.

Now, I use a Dremel engraver and have no problems. I use light pressure on soft woods and harder pressure on hard woods. It took a bit to get used to using it, but after some practicing, I could write legibly.

This is what works for me.

keith

Re: Signing your work revisited

#10

Re: Signing your work revisited

Jennifer@Indy.USA

>I tried a Razor-Tip pen at the Wood Show last weekend that I may buy for signing. I think it was called a micro writing tip. It was veeeeery tiny and you could really write fantastically with it. Better than any other burring tip I've tried. I'm with John though, I've been using a Dremel engraver for years and find it to work the best for me. When I use a magnifying lens I can sign my full name in cursive on the bottom of my tiniest mini's. About 1/4" diameter.

Jen

Re: Signing your work revisited

#11

I like your idea of using the magnifier

john lucas

>

Re: Signing your work revisited

#12

Re: Signing your work revisited

stacey s

>I use an archival pen as well. You can get it at your local Michaels craft store. It is made by Sakura. It is called a Micron. They come in various sizes from very very small to pretty large.

Stacey

Re: Signing your work revisited

#13

Keith Tompkins

Re: Signing your work revisited

keith tompkins

>HI Stacy, I use the same one, I think ..Pigma Micron #005 archival ink pen. These are available at most art stores, under three bucks for me.Line width is 0.20 mm. My local art supply store carries the entire line. I have had my share of disasters with other methods; these are perfect!

Re: Signing your work revisited

#14

Re: Signing your work revisited

Bob Fawcett

>Is the dremel engraver a rotary device, or one of those vibrating tip devices with a very hard point?

I have one of the vibrators from 30 years ago when I used to mark alll my tools. For some reason I never thought to try it until reading this.

Re: Signing your work revisited

#15

Re: Signing your work revisited

Bill Youngblood

>One more suggestion Mike. I use a uniball pen. They are available at Staples for $5.95 for a package of 4. I sign before applying finish and then it won't smear.

Bill

Re: Signing your work revisited

#16

Re: Signing your work revisited

Mike Cunningham (Cape May NJ)

>Yes it helps.

Thanks very much!

Re: Signing your work revisited

#17

Thanks!

Mike Cunningham (Cape May NJ)

>

Re: Signing your work revisited

#18

Thanks to both of you!

Mike Cunningham (Cape May NJ)

>

Re: Signing your work revisited

#19

Thanks Bill!

Mike Cunningham (Cape May NJ)

>

Re: Signing your work revisited

#20

Dremel ?

Mike Cunningham (Cape May NJ)

>Thanks John, Is there a particular tip that you use on the Dremel or is a "Dremel engraver" an animal unto itself?

Re: Signing your work revisited

#21

Yes, good idea!

Mike Cunningham (Cape May NJ)

>

Re: Signing your work revisited

#22

Re: Signing your work revisited

Mike Cunningham (Cape May NJ)

>Dremel may be the answer though I'm going to look at the various pens that have been mentioned. I don't like the Sharpie at all and as I said I have trouble with burning but perhaps I need to use a different tip.

Re: Signing your work revisited

#23

Re: Signing your work revisited

Mike Cunningham (Cape May NJ)

>I'll be near Michael's tomorrow a.m. so I'll check it out. Thanks!

Re: Signing your work revisited

#24

Re: Signing your work revisited

Mike Cunningham (Cape May NJ)

>I've seen your signed work and that's what I'm seeking, so this may be the way to go. Thanks Keith. By the way, how's the project with holly coming along?

Mike

Re: Signing your work revisited

#25

Thanks Bill!

Mike Cunningham (Cape May NJ)

>