WE MOVED...
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Butternut Bowl

Posts

Butternut Bowl

#1

Brad Vietje

Butternut Bowl

Brad Vietje

>A simple bowl in Butternut. 10" diameter by 4" high.

Safe spinning,

Brad Vietje

Newbury, VT


img

Re: Butternut Bowl

#2

Brad Vietje

Unfinished Bottom showing Scalloped Figure

Brad Vietje

>This was a nice batch of Butternut -- beautiful scalloping about 3" under the bark. Bad pic, but pretty wood.

Safe spinning,

Brad Vietje

Newbury, VT


img

Re: Butternut Bowl

#3

Re: Butternut Bowl

Russ Babbitt Jr.

>Nice simple bowl. Beautiful figure.

P.S. Nice foot Brad.

Re: Butternut Bowl

#4

Mike Stafford

Re: Butternut Bowl

Mike Stafford

>Very attractive, Brad. I like butternut and you did a fine job with it.

Re: Butternut Bowl

#5

Waaaay Nice, Brad!!

Michael Stadulis, in Gloucester County, NJ

>

Re: Butternut Bowl

#6

Re: Unfinished Bottom showing Scalloped Figure

George Van

>Nice bowl Brad, I wish I had some Butternut in our woodlot. I like the care you took balancing the growth rings, It makes the bowl.

Re: Butternut Bowl

#7

Leo Van Der Loo

Lovely bowl Brad

Leo Van Der Loo

>I do like butternut for turning, I still have a few rough blanks in the shop, I did give most of my last log to the turners club to be raffled off, just to much to turn all myself.

You gave it a nice profile, and I like the rounded and wider edge, shows the grain off so well.

Good job, love it.

Have fun and take care

Leo Van Der Loo

Re: Butternut Bowl

#8

Very nice job on that butternut.

Don Henthorn

>up to your usual skill level. U would like to be where butternut grows again I always made a special effort to harvest some nuts for the winter. Been nearly sixty years since I have even seen a tree.

Re: Butternut Bowl

#9

That is some beautiful grain!!

MIke from St. Clair Shores

>Brad,

You've really been busy. Thanks for posting all the pics of your work. That butternut has some really nice looking grain. I haven't been lucky enough to get a piece yet, but I'm going to keep my eyes open for it now.

Mike

Re: Butternut Bowl

#10

Re: Butternut Bowl

Allen Neighbors

>Beautiful Bowl, grain, too. Brad, it looks like the bowl itself is thinner than the rim... is that true? It really makes the bowl look great! Would that technique help prevent later cracking?

It also looks like it's fairly porous wood... sort of like oak... how does it turn?

Thanks for posting.

Re: Butternut Bowl

#11

JL

Re: Butternut Bowl

JL

>Nice bowl. But the big question is can I get enough for a seat blank??? Please??? Beg, beg, beg :).

Re: Butternut Bowl

#12

Brad Vietje

Re: Butternut Bowl

Brad Vietje

>Allen,

Thanks for your comments. Yes, the bowl is thinner in the sides than in the rim -- the inside has a very slight undercut, but no where near as sharp as the flare on the outside.

Butternut is quite porous, and very soft, and very light. It is tough to get a real nice finish off the gouge, so most pieces need quite a bit of sanding. Red Oak has similar open pores, but is much harder and heavier, and less prone to dents.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Butternut Bowl

#13

Brad Vietje

Thanks, everyone

Brad Vietje

>I appreciete the kind words. JL -- contact me directly -- I still have to retrieve the base of the tree trunk, so it's not impossible to get a seat blank out of it --I'll need to know how big and all that.

Safe spinning,

Brad Vietje

Newbury, VT