Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Drill press help

Posts

Drill press help

#1

Drill press help

Don in Denver

>Minding my own business, enjoying not being able to get in to work due to the blizzard, and drilling a hole in a blank for a screw chuck. All of a sudden the drill chuck falls off the arbor. I have not been able to press it back onto the arbor very far using just gentle pressure against a piece of wood and pushing down as if I were drilling a piece. How do I re-seat the chuck? and why did it come off in the first place? Thanks

Re: Drill press help

#2

Roger in MO

Re: Drill press help

Roger in MO

>Don, If the Morse taper fell out of the quill, sometimes it takes quite a blow to reseat it, making sure no foreigh matter or corrosion is in either the bore of the quill or on the taper. If the taper has a tang, be sure it is orientated correctly in the quill. If its the shorter, steeper taper where the adaptor fits into the chuck itself, possible the same but I've never had a problem with that. Cause--Gremlins? Temperature chage? corrosion?

Roger in MO where it was 60 degrees and sunny today!

Re: Drill press help

#3

Re: Drill press help

Brian Myers

>If it is a morse taper, clean the taper and chuck. Put a wood board on the table, raise the table to hold the chuck in place, lock table in place and pull down on the handle/wheel(hard) forcing the chuck into the board. The chuck should no be wedged back on the taper. Or at least these are the directions that came with my drill press. Hope it helps.

Re: Drill press help

#4

Re: Drill press help

Mike Cunningham (Cape May NJ)

>It may have come off due to dirt, corrosion, etc. on the morse taper, both surfaces, the chuck and drill press. Clean both well and lubricate. Set the chuck back in and using a block of wood and mallet, give it a smack and seat it. That should do the trick.

Mike

Re: Drill press help

#5

I had that happen

Don Henthorn

>and I blamed it on using the drill press for sanding. I think the axial pressure causes the taper to loosen. Probably wrong, but that is my belief.

Re: Drill press help

#6

Re: Drill press help

Don in Denver

>Thank you all for the suggestions. I will get to it tomorrow and let you all know.

Re: Drill press help

#7

Re: I had that happen

john lucas

>Don I use mine for sanding with drum sanders all the time. Haven't had a problem with it coming loose. I have removed it several times to use that chuck for other projects and when I insert it I use the board and leverage technique mentioned above.

Re: Drill press help

#8

Re: Drill press help

Frederick Nelson

>Check to be certain there isn't another way of securing the chuck in the Morse taper. My drill press, a Craftsman of 1988 vintage, uses a collar on the chuck that secures the chuck in the taper. If the collar isn't threaded on the quill, the taper simply doesn't seat all the way. (You actually have to start threading it on the quill most of the way before you can seat the Morse taper.)

Sounds as though this collar might have worked itself loose over time, allowing the chuck to fall out of the Morse taper. By unscrewing this collar, the chuck may be extracted from the quill.

Fred

Under nearly clear skies in Eastern Missouri

Re: Drill press help

#9

Here's my fix...

wcturner

>When mine dropped out a couple years ago, I cleaned both surfaces. Placed it in the oven, at about 300�, for about 30 minutes.

Before removing it from the hot oven using a mitt, etc., have a piece of wood on your drillpress table(which I did not, & it marked my table. Get the chuck into the drillpress before it cools off, & using the drillpress handle to press the chuck down on the wood.

Mine has not loosened up since.

Re: Drill press help

#10

Re: Drill press help

Don in Denver

>Used the drill press handle to push the chuck back on as you recommended. It seems to work okay now, although I'm not sure it is totally seated. Wil just watch for now and see how it goes. Got to go dig out the car and try to make it to the grocery. Got about 30" of snow.

Re: Drill press help

#11

Re: Here's my fix...

Ed in Leaside (Toronto, Ontario)

>'Twould be easier to put the taper in the freezer for an hour or 2. This would be okay to mount the chuck on the Jacob taper, but not to put the taper in the DP if you might ever want to remove it. We used to do this for mounting bearings in side-frames, or for shafts in bearings. To remove the bearing would often require grinding out the race.