Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Maple Hollow Form (PICS)

Posts

Maple Hollow Form (PICS)

#1

Maple Hollow Form (PICS)

Mike Rubes, Apex, NC

>Hi all,

This is a maple hollow form with rosewood collar. This one was very fun for me because it was my first hollow form that I've taken straight from the tree to finished product! I've turned a few from dried timber, but never from wet. I roughed it back in April or so, alcohol soaked it and set it on the shelf. About 2 weeks ago, I mounted it up and finished it. The maple was a little soft, but still turned nicely. I like the one line of ambrosia across the top.

It is about 7 inches across and 4 high. I left it pretty thick as again it felt soft and sounded thin to me. It is about 1/4 inch thick, maybe a bit less at the rim. Finish is Tried and True and then buffed. It's a Christmas gift and is already wrapped and under the tree!

I think the form is ok. My pictures need work, for sure. The bottom could be a little smaller I think and maybe a bit more "lift" along the bottom edge? Comments and critiques are always welcome.













Thanks for taking a look,

Mike

Cleaned enough to see the shop floor in Apex, NC!!

Re: Maple Hollow Form (PICS)

#2

Re: Maple Hollow Form (PICS)

David Breth

>Mike -

That is very nice. I like the ambrosia too - looks almost like a belt!

David B.

Re: Maple Hollow Form (PICS)

#3

Brad Vietje

Nice ! I like the racing stripe...

Brad Vietje

>

Re: Maple Hollow Form (PICS)

#4

Nitpicking here...

david

>I like this piece, Mike. Since you asked for comments, here goes: I would have continued the curve to die on the bottom with a smaller diameter rather that have a bit of a foot. Keep in mind that I prefer not to have a foot in all my pieces. The curve sort of flattens out just below the widest point. This is both a plus and a minus. On the plus, it makes for a more distinctive piece. On the minus, I believe continuing the curve would have made a more "uniform" shape. Just my two pennies worth.

Re: Maple Hollow Form (PICS)

#5

Brad Vietje

Tried & True question

Brad Vietje

>I've been using T&T Original for a month or so when I wanted a low sheen finish... I might want to buff a few of them. How long did you wait before buffing ?

Safe spinning,

Brad Vietje

Newbury, VT

Re: Maple Hollow Form (PICS)

#6

Re: Nitpicking here...

RevDoug

>David, I was thinking the same thing, that the curve seems to flatten out. But a pretty nice piece altogether.

Re: Maple Hollow Form (PICS)

#7

Re: Nitpicking here...

Mike Rubes, Apex, NC

>Hi David,

Thanks for your note and suggestion. It's funny, but I never even considered *not* putting a foot on it, but as soon as I read your post, I could see what you were saying and I agree. I think the foot is ok, and I do like the way it "lifts" the piece, but it is a little abrupt and tends to draw your eye (at least mine) to it. I think a smooth transition on the bottom with no foot would have indeed been better. Good suggestion.

I struggled getting the right slope/shape to the underside of the body and I think it is because the curve should have naturally continued on, but I was stuck in "foot mode" and tried to force it a bit. The beauty is I have a lot more of this maple so think I'll give another one a spin during my week off at Christmas!

And I would never think a good, constructive critique was "nitpicking" :)

I hope all is well in Hawaii,

Mike

There's always a bowl waiting in Apex, NC!

Re: Maple Hollow Form (PICS)

#8

Re: Tried & True question

Mike Rubes, Apex, NC

>Hi Brad,

It varies quite a bit depending on my available shop time, but I've applied the T&T varnish with a paper towel and then rubbed it with a dry towel (while still spinning) and buffed it with the Bealle system 30 minutes later. Or, I've waited a week until I could get back into the shop! I've not noticed any difference in how the final finish looks. The T&T seems to dry pretty quickly. I keep mine in a ketchup squeeze bottle (new one, never had ketchup in it!!!) and that way can just squeeze out a drop or two at a time onto a papertowel and use that to apply a little bit at a time.

Good luck!

Mike

Might even (GASP!!) drop below freezing tonight in Apex, NC!!!