Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Need help getting large blanks onto lathe.

Posts

Need help getting large blanks onto lathe.

#1

Need help getting large blanks onto lathe.

Al Crandall (N.E. of Indy)

>I am becoming interested in deep hollowing, as in 24". I have just about finished construction of a deep system so the hollowing part isn't a problem. But as I rolled a former bowl blank toward the shop door I realized that I can't get the 18" x 24" log up to the lathe bed. I'm thinking of a ramp and strap loop attachment for the lathe similar to what you see on the portable saw mills. Anybody have pictures of how you get heavy logs lifted between centers?

Re: Need help getting large blanks onto lathe.

#2

Re: Need help getting large blanks onto lathe.

Bruce Wiseman

>Well I don't know exactly what they call those things used in auto places that look like a platet jack on the base and an arm with a chain on the top. They wheel it up under the front of the car and use it to pull the motor out. If you have any idea of what I'm talking about, I think Harbor Friegt sells them. I'll poke around on their site and see if I can find one. Used to lift the motor out off the mounts and move it. It would be moveable and able to lift most of the sizes wood you are talking about.

Re: Need help getting large blanks onto lathe.

#3

Re: Need help getting large blanks onto lathe. *LINK*

Bruce Wiseman

>Just when I thoughtI might have had an original idea, I remembered turning Lisa Oland's studio and seeing them using such a device.


Oland Studio Pic

Re: Need help getting large blanks onto lathe.

#4

Re: Need help getting large blanks onto lathe.

Doug Thompson near Cleveland

>A engine hoist is a great idea... I was going to suggest a chain fall. They do make engine hoists that fold up when not in use. That 24" bowl turned at Indyfest was huge but this will be very interesting, take some pictures.

Re: Need help getting large blanks onto lathe.

#5

Re: Need help getting large blanks onto lathe.

john lucas

>Al I asked this question a while back because I realized that I'm not getting any younger and the logs were getting bigger. Most of the responses suggested an engine hoist of some sort of chain hoist mounted over the lathe.

You already have the tilting tailstock device. Simply build a tilting lathe device. Then you can tilt the lathe over, roll the log up , screw it on an tilt the lathe back. Might take some pretty hefty counter balance weights. Or you could simply put in a pit with hydraulics like the old garages. Lower the lathe into the floor, put the log on and raise it up. :) Sorry, worked too long yesterday so I'm a little squirrly this morning.

Re: Need help getting large blanks onto lathe.

#6

JL

Re: Real Squirrelly... LOL *LINK*

JL

>tilting lathes?? Al, an engine hoist would be a good thing. We have another type at work though. It has a platform that can be raised and lowered. A platform might (or might not) be an advantage. Here is a link to the Wesco Lift site.


Wesco Lifts

Re: Need help getting large blanks onto lathe.

#7

Re: Mounting A Big'un

Mark Mandell - Gone Round In Jersey

>Here's a pick of one of the Stubby owner's solution. The winch is from Harbor Freight, often on sale at $60, and the track is for a barn door. I copied the same thing in my shop. 8' of track, winch, travelers, came to about $90. Takes up no floor space.


img

Re: Need help getting large blanks onto lathe.

#8

Re: Need help getting large blanks onto lathe.

Al Crandall (N.E. of Indy)

>HI Bruce. The thingy you refer to is an engine hoist, and I own one. The problem is that they take a 40 acre field to manouver into place, and I don't have very much room around my lathe. I used it to move two large pieces of machinery into my shop so I know just how much trouble it is to use. I'm looking for something more compact. Thanks.

Re: Need help getting large blanks onto lathe.

#9

Re: Wow!!! I've only got a 24" lathe.

Al Crandall (N.E. of Indy)

>

Re: Need help getting large blanks onto lathe.

#10

Re: We maxed out that Vega, didn't we Doug?

Al Crandall (N.E. of Indy)

>I wasn't feeling well at Indy Fest so I was grateful for the help getting that blank lifted and positioned. A large diameter 2 prong drive center would have reduced the rough out time by several hours, but we persevered.

Re: Need help getting large blanks onto lathe.

#11

Re: You've got to be kidding!

Al Crandall (N.E. of Indy)

>A tilting lathe is totally unreasonable, but I like the pit idea with hydraulics. I'll start digging tomorrow.

Re: Need help getting large blanks onto lathe.

#12

Re: That's classy, but there is a headroom problem

Al Crandall (N.E. of Indy)

>I like this Mark, but I have 7' garage doors in my shop with 8' an ceiling. The lathe sits under one of these doors when the door is open. Getting the track mounted under an open door isn't insurmountable but it is problematic. Maybe one end of the track could be mounted on a permanent pivot, and the other end supported by a tall tripod on wheels. Or maybe I just need to move the lathe.

Re: Need help getting large blanks onto lathe.

#13

Re: Headroom

Mark Mandell - Gone Round In Jersey

>Ceiling (bottom of joists) over my lathe is 6-10. The winch on the track stays well out of the way when not in use. Mount your winch track on the ceiling joists above the garage door tracks. There are brackets available to fit the tracks, but I just used 2 #12 2" screws in each joist.

Roll your log in, close the door, slide the winch over and set your log, move the winch and open the door again. But you had that figured out already, right?

|;-}}

Re: Need help getting large blanks onto lathe.

#15

Re: You've got to be kidding!

John Lucas

>Al use your imagination. All you need is two lathes. one mounted opposite the other one and hopefully the same weight. Thier mounted to a thick concrete platform with a pivot point. Then you can just flip the lathe to the one you need, bowl lathe on one side and spindle lathe on the other. Obviously at christmas time I need more to do at work than think up stupid ideas like this one. Wish I had the skills in photoshop to create a picture. I can just imagine having a rotating platform with a Stubby on one side and Oneway on the other.

Re: Need help getting large blanks onto lathe.

#16

Re: Mounting A Big'un

George Van

>Good idea Mark, is that the track like I have for the sliding door on the pole building? If so I should be able to get one at Menards.

Re: Need help getting large blanks onto lathe.

#17

Re: Need help getting large blanks onto lathe.

Bill Hale / Woodspinner

>Marks system is close to what I plan to build. My idea is 4 legs with a bar track on each side of the lathe, 10 ft wide. Then add another barn track on wheels supported by the first two bars. Put the winch on that, also hanging on wheels, and now you have a full motion gantry.

I tried the engine unit and ended giving it away.

Mark I love the tire chain idea !

Good turning and be safe

Bill in Casa Grande, AZ.

Re: Need help getting large blanks onto lathe.

#18

Re: Mounting A Big'un

Mark Mandell - Gone Round In Jersey

>George,

The track in the pic is the square type for regular wheels. I used the round track for ball-type trolly wheels, but yes, this is barn door stuff. My track's rated at 800 lbs. which is way more than I'm ever going to try to mount on my lathe.

The pic shows the hoist of a bowl blank. If lifting a longer log section, say 24" to 36" or so, you'd do well to rig a beam and double strap assembly to better control the load.

mm

Re: Need help getting large blanks onto lathe.

#19

I take it that asking Karyn is verboten???

KurtK in Indy

>Not that I would dare ask my wife to help....Anyhow, what about jury rigging some type of boom or jib crane. Perhaps you could track down a decent size hunk"o"I Beam and do your Al Crandall thing and design it upon a heavy duty turntable and mount that baby to the floor of the garage. Then find that 250'hoist from Harbor Frt or somewhere and get it on a piece of unistrut or the like. When not in use, you could swing the arm against the wall.

Or....if you want to spend the $$, I think I have a complete jib crane (light duty...industrially speaking) in one of my buyers books. And of course I would give you the kissin' cousin discount...

Call me if you want to discuss.

Kurt

Re: Need help getting large blanks onto lathe.

#20

Re: Need help getting large blanks onto lathe.

Doug Trembath

>I've been toying with an idea for some time of gluing up an "I" beam and building a wooden trolley to hold a chain hoist, much like a jib trolley does, but not swingable. Mounted to the ceiling, the system would span longer than the length of the lathe, allowing inboard and outboard mounting and removal. Anyone have a "round tuit" I can borrow for a while? Still working on setting up my new Unisaw! (gloat)

Doug Trembath

Studio in the Woods

Re: Need help getting large blanks onto lathe.

#21

Re: Need help getting large blanks onto lathe.

Bob Fawcett

>Al,

Build a ramp up to the bed of the lathe, mount the winch on the wall behind the lathe, loop the cable around the log and hook it to the wall behind the lathe as well. Place the log at the bottom of the ramp with cabled looped around. When you crank the winch it should roll the log up the ramp.

Re: Need help getting large blanks onto lathe.

#22

Thanks Mark!

George Van

>

Re: Need help getting large blanks onto lathe.

#23

Re: Bought the trolleys tonight at Menard's.

Al Crandall (N.E. of Indy)

>Menard's has a "15% off anything which will fit into this bag" sale right now, so they became the cheapest supplier for the trolleys and got my business. Lowe's is the cheapest source for the square track by about $6 per section. When I figure out how to get through the drywall ceiling and attach the track in a way which I feel is secure I'll be buying the track. I AM NOT going to rip out 10' of ceiling.

Re: Need help getting large blanks onto lathe.

#24

Re: Karon gave blessing for MS460 w/ 28" bar.

Al Crandall (N.E. of Indy)

>I know better than to push my luck. New chainsaw for the Stihl stable is enough.

Re: Need help getting large blanks onto lathe.

#25

Re: That was my first idea, Bob.

Al Crandall (N.E. of Indy)

>It is probably the easiest method, and the one which I was considering when I mentioned the loader for the portable saw mill. But the more I think about it, the more I like the idea of being able to let the load hang while I position the centers in addition to getting the load up to bed height.