We value your privacy.
We use cookies to enhance your browsing experience, analyse site traffic, and personalise content.
By clicking “Accept all”, you consent to our use of cookies. You can also choose
“Essential only” or learn more.
>You are correct sir. It works especially well on segmented work. Don Russell uses a convex bevel skew to "scraper" his segmented work. He sharpens it by laying the skew almost flat on a belt sander and then lifting the handle until it cuts up to the end. Then he does the other side. It produces great little curls when cutting laminated pieces and boy talk about easy to sharpen.
>1 1/4" P&N, 1/2" Crown, 1/2" Hamlet rolled edge, 1" Carbon Steel, 1/2" Carbon Steel. All are rectangular with the bottom edge rolled and the corners broken on the top edge. Except for the Hamlet that came with both the top and bottom edges rolled. I grind the top edge flat on the Hamlet right by the tip so my point is very sharp. The 1/2 carbon steel skew has the last inch of the top edge tapered down so it only has a 1/4" cutting edge. I tried the Lacer grind and went back to a strait cutting edge with a hollow grind. I do use them for light finish scraping as well as rolling beads and other spindle work. I hone with a diamond card and then either strop or use a fine ceramic stone. Which ever I grab first, either way the edge will shave hair and cut wood.
>I have been using a 1" carbon steel with curved grind and radiused bottom corners and have got over the initial learning curve. Now something is puzzling me and you learned skew users might be able to help. In use, mainly the bottom corner is where all the action is. So why do we have big wide skews and only use a small piece of the cutting edge? Surely a narrower skew, say 1/2" works just as well? If it's because of a potential vibration problem then wouldn't thicker work just as well? If we used a 1/2" x 1/2" square skew have we stumbled upon a bedan? If so why are we using *^&$#@&* skews? Sorry that's more than 1 question :-)
>For me the narrower the skew the easier it is for me to get into trouble with that long point. When it took Stuart Batty's classes he had use rolling beads with a bedan and a wide parting tool. Of cousre he said the only thing a skew was good for was opening paint cans.
>I'm far from being a "learned" skew user (they still scare the heck out me at times) but I think simply put, the larger the skew the larger the "sweet spot" becomes and also more controllable. You wouldn't want to try to turn a large newell post or table leg with a 1/2" skew.
Some people prefer to roll beads with the heel, or short point, while others use the toe, or long point. There are a number of other cuts that can be made with the skew, and how many you can use with your skew(s) will depend on who you've learned from, and how the tools are sharpened. For example, if you watch Richard Raffan's box turning video, he shows a radiused edge skew flat on the rest (can't be easily done with an oval skew), used to shape and/or clean up the outside surface of a box. I do this all the time with my curved skew, but it doesn't work with a skew that's straight-edged. I also make a peeling cut to very quickly size tenons or remove waste on the end of a spindle, and this is done with the long point of a gently curved skew held flat on the rest. Usually planing cuts to make smooth cylinders are done not with one point or the other, but with a small area just below center (roughly the lower 1/3 of the edge) with either point down.
The shorter answer would be to use whatever tool gives you the best results with the least stress. After some practice, and a number of ruined pieces, I now feel that the skew is my preferred tool for certain cuts, though I still find it easier to make beads with long-bevel detail gouge.
>I use all parts of the skew. I use the lower 1/3 mostly for shaping and general spindle work. I use the heel and toe to turn beads. I'll use the upper 1/3 with the toe down (now it's the lower 1/3) for shaping when the lower part gets dull (which I try not to let it do).
I also use the upper 1/3 or even 1/4 for turning coves. Yea I know they say not to do that. I find that the upper quarter of a 1" skew is really no different that using a 1/4" skew. the short bevel at this point lets me turn coves that are failure narrow. Since you have more leverage acting against the tool you have to take smaller cuts, just like using the 1/4" skew.
I don't find the oval skew all that bad for peeling cuts. I don't do it a lot because I prefer to use the rough out gouge for this. It's much faster to sharpen my rough out gouge than the skew so I save the skew for final shaping and clean up. When I do a peeling cut I don't use all the blade. I use the heel end and rock the tool so the heel is lower than the toe just slightly. This puts more support under the heel portion on the tool rest and it's quite controllable.