Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Modified my hollowing rig already.

Posts

Modified my hollowing rig already.

#1

Modified my hollowing rig already.

Allen Neighbors

>I tried out my new hollowing rig on a small hollowform, and it worked very well. Then I put on a larger piece of wood, shaped it with a lower profile and larger diameter, and right in the middle of turning, had to stop and make a modification.

The restraining bars, at 21 inches, were too short to allow me to swing the tool holder far enough toward the offside, to get the cutter all the way to the desired outer wall thickness of the lower profiled HF.

I made new bars, 40 inches long, which gives me 37.5 inches of travel. Now, it works. :o)

Larry Zarra suggested this to me the other day on another forum... should have paid attention, huh?! :o)

Just wanted to post this, so maybe I could save someone else some problems.

Re: Modified my hollowing rig already.

#2

Brad Vietje

Re: Modified my hollowing rig already.

Brad Vietje

>Allen,

I only use my captured rig for larger pieces, but mine has the bars offset quite a bit from center. I set them up so the long ends face away from me, toward the wall, for better access to wider, flatter forms. I had to move the tail end of the lathe away from the wall to accomodate this.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Modified my hollowing rig already.

#3

Re: Modified my hollowing rig already.

Mike from St. Clair Shores

>Allen,

I also thought that you had the outrigger on the wrong side. It restricts the angle you get when you want to cut up under the collar. I always keep mine on the side towards me then you can swing it out away from you more. The way yours looked it was possible to flip it and have more swing. If I haven't made this clear I hope the picture will help. JMHO

Mike


img

Re: Modified my hollowing rig already.

#4

Re: Modified my hollowing rig already.

john lucas

>I'm going to look at making a curved captured tool rest. I thought about making really long and aslo making it adustable so that it will slide from front to back but then it seems like I would have to adjust it all the time. I thought that if it was curved toward the headstock you would have a lot more movement of the boring bar without having to adjust the captured tool rest.

Re: Modified my hollowing rig already.

#5

Re: Modified my hollowing rig already.

Barry Irby

>John, my engineering brain is going "But wait..." If you made the restraining bars curved so that they are a radius around the opening, they will be weak in the middle. I don't know how strong the have to be, but if they are curved they will be much easier to pry apart in the center. I can't think how to explain this. Are you following my explanation?

Re: Modified my hollowing rig already.

#6

Try a differant handle

Phil Joines Krum, TX

>I don't use the D handle any more. Try making one from 1" x 2" square tube. It's a lot more manuverable. Mine's filled with lead shot to reduce vibration. The laser support connects to the side using threaded inserts.

Re: Modified my hollowing rig already.

#7

Re: Time For A New

Mark Mandell - Gone Round In Jersey

>Stubby, John. Then, instead of curved or sliding bars and such, you'd simply extend and swing the whole bed away from you and thus be able to approach the wood at a truly low angle to have your tool just under the rim but with the toll holder still remain captured!

mm

Re: Modified my hollowing rig already.

#8

Re: Modified my hollowing rig already.

john lucas

>Barry that's the beauty of hollowing rigs. You have the cutter lined up exactly on center so there is virtually no torque. I made my first one really wide thinking you had to have all this leverage to counter the torque but there isn't any. My latest boring bar is only about 5" wide and I use a wooden secondary tool rest. It works great but I spend too much time adjusting it for clearance if I have an odd shaped vessel.

Re: Modified my hollowing rig already.

#9

Re: Time For A New

john lucas

>Mark I truely think the Stubby is the perfect lathe for me with all the varied things I make. However I also think a Porche is the right car but that ain't gonna happen either. Oh well. Me and the Powermatic will just have to get along for a little longer.

Re: Modified my hollowing rig already.

#10

Re: Until Then

Mark Mandell - Gone Round In Jersey

>I'm sure you'll do just fine with your Mustard Monster. If your capture bars don't slide, I'd strongly suggest a bit of modification to increase their reach. Mine are 36" long but slide either way through a 6" clamp which gives me about 65" of arc to work in without moving the bed.

|;-}

Re: Modified my hollowing rig already.

#11

Now you know why I designed my rig with a pivot.

Al Crandall (NE of Indy)

>Hi Allen. Remember the hollowing rig I was demonstrating at TD's gathering? The two bars of the secondary rest are mounted on a long, wide plate with a pivot offset to the headstock end. This lets me address the work opening at an extremely shallow angle with just a simple finger push of the plate around its pivot. The bars swing around to the back side of the lathe and can be parallel to the bed if I so desire. They keep nearly the same geometric relationship to the main tool rest at all times. This allows the bars to be kept to a minimum length, about 18" if I remember correctly. And 6" of that 18" is used up by the boring bar and its outrigger. It can't be made much simpler.

Re: Modified my hollowing rig already.

#12

Re: Modified my hollowing rig already.

Lan Brady

>Allen,

Another possibility. Take a look at "the Gathering" pictures. Al Crandall's captured rack had a base that lets it pivot right or left, thus allowing you to get under the rim with ease. I copied his design and mine works with a 16 inch captured rack very well.

Good Luck, Lan

Re: Modified my hollowing rig already.

#13

Re: Now you know why I designed my rig with a pivo

Lan Brady

>See how simple, Al responded before I could hit the send button on my response.

Lan

Re: Modified my hollowing rig already.

#14

Re: Modified my hollowing rig already.

Allen Neighbors

>I did the same... almost... I put more of it to the back side of the lathe, but I also extended it on the front side too. That way I can get curved toolbars into a small opening. But it is offset mostly to the back.

Thanks for posting. :o)

Re: Modified my hollowing rig already.

#15

Re: Modified my hollowing rig already.

Allen Neighbors

>I've been using mine this morning, and I had to stop and think about what you said about restricting the angle while cutting under the collar... then I got it. I understand what you mean... by having the anti-torque bars on this side, the side with the cutter will go farther over to the offside of the lathe. Right?

Thanks for posting... this may help me out some more. :o)

Re: Modified my hollowing rig already.

#16

Re: Modified my hollowing rig already.

Allen Neighbors

>John, I thought about that while I was turning this morning, but with my limited ability to weld, and limited funds too, I put that thought aside, quick. I think it would be pretty hard to keep the restraining bars absolutely flat while maintaining the arc. Clear as mud?

Being able to swing the anti-torque bars around towards the headstock would surely be an asset to the system! It would make it easier to get to the inside of wider, shorter forms, for sure. Good idea, but hard to accomplish, in my mind. I'd sure like to see a pic or two, and a tutorial, if you get it done. :o)

Re: Modified my hollowing rig already.

#17

Re: Modified my hollowing rig already.

Allen Neighbors

>Barry... middle support leg under the center of the lower arc, and a cantilevered bridge above the upper arc. Lot of extra metal in the system, but the only way that I can see to keep them from separating more. The strength required would depend on the hardness of the wood and the aggressiveness of the turner. :o)

I guess you can see that I'm not an engineer, huh?!!

Good thoughts on the subject from you, Barry.

Re: Modified my hollowing rig already.

#18

Re: Modified my hollowing rig already.

Allen Neighbors

>John, my anti-torque framework is only 5" wide outside measurement, too. (Is that what you are calling your boring bar?)

"Wooden secondary toolrest"... Do you not have a set of Restraining Bars that the boring bar slides between?

(At sea, here.)

Re: Modified my hollowing rig already.

#19

Re: Try a differant handle

Allen Neighbors

>I'd sure like to see a picture of that connection with the threaded inserts, Phil.

Re: Modified my hollowing rig already.

#20

Re: Now you know why I designed my rig with a pivo

Allen Neighbors

>Al, I didn't get a good look at it, at TD's, because I was too busy trying to learn other things. :o( A pivoting restraining system would be awesome! Never thought of that. It sure makes sense, though. (Guess that's why I didn't think of it.) :o)

Are there some photos posted of your rig somewhere? Or is it a patented thing? Curious.

Re: Modified my hollowing rig already.

#21

Re: Modified my hollowing rig already.

Allen Neighbors

>I'll dig 'em up, but I don't remember seeing that in the Gathering photos.

Thanks,

Re: Modified my hollowing rig already.

#22

Here's one *LINK*

Phil Joines Krum, TX

>This one, from MSC, is a bit pricy. I've had mine for 20 years so don't know who all stocks them. Maybe HF. The one I have can use inserts from #6 to 3/8 in either aluminum or steel. I originally used them to mount stuff on dune buggies.


http://www1.mscdirect.com/CGI/NNSRIT?PMAKA=09331554

Re: Modified my hollowing rig already.

#23

There's another way to do it

Phil Joines Krum, TX

>Make some bent bars to hold the cutter. If you have an A/C torch the normal 5/8 round stock isn't that hard to bend. If you make the bend like a question mark with the cutter on the center line of the bar you can use it as a hand held hollower too.

Re: Modified my hollowing rig already.

#24

Overkil?

Jorge Castaneda

>Good morning Mark,

Have you had a piece that needed all those capabilities? or could a fellow do with a smaller rig? if so please suggest dimensions...Thanks

Jorge

gathering momentum to build his rig

Re: Modified my hollowing rig already.

#25

Re: Overkil?

Allen Neighbors

>Jorge, Look for an Al Crandall post in this thread. When I searched, I found some pics that I took of his rig. It's much better for maneuverability than the one I built. His pivots, thereby making it easy to get inside the collar.

Using mine this afternoon, I found that, because of the way I built my mount, and the length of the bars, I can pivot mine enough to get inside under the collar. I can't think of a form that that won't work on.

My bars are 40". But if you make the mount like Al Crandall's, you can get by with 18" or so length.