TD how long do you...
Paul Porter
>...keep it running? I tried it and I couldn't stand the noise after about 15 minutes.
Knowledge You Can Build On — Est. 1998
TD how long do you...
Paul Porter
>...keep it running? I tried it and I couldn't stand the noise after about 15 minutes.
Re: TD how long do you...
TDaniel
>My tumblers are outside. They run for 2 to 3 days to clean up the inside of a piece but I am experimenting with some silicon carbide added to the rocks and that appears to speed up things. It would be nice to be able to reverse the piece as the inside feels smoother when rubbed in one direction than when rubbed the other way. Before everyone jumps up and builds one of these let me again state that at the present it is an ongoing experiment and it may or may not have any substantial value.
Re: TD how long do you...
gil jones
>With a slightly longer belt (or room to adjust), you could but a twist in the last (slowest) belt. Or disconnect the start capacitor, and spin-start it by hand in either direction. Terry, does it work well enough to be worth all this �engineering�?
Does it work well enough?
TDaniel
>Gil, on small opening hollow forms where you can get your fingers inside far enough to feel it is the easiest way I have found to get the inside smooth enough. I do not use collars to reduce the size of the openings. It would certainly be easier if I used collars but I choose not to. Is it worth it? I am still experimenting with it and will withhold any answer until I have more valid statistics but so far I have been pleased with the results most of the time. Some shapes tend to shift all the rocks to the middle and don't clean up the part near the hole that you can reach with your finger and the tumbler cannot be used with pieces with large voids. There are limits to what can be cleaned up with a tumbler but mine was built for less than $20 so if it works a few times I cannot loose.
Re: HELP!! (TD or other Genius Minds)
jmohnike
>Multiply the diameter of the pulley on the motor (driver) by the rpms of the motor. Divide that by the diameter of the driven pulley.
2�X1750=3500 3500/4=850
Basic but close enough.
I have my motor on a side to side sliding mount and it has a 4 step pulley on it. The belt goes to a jack shaft which has 2 4 step pulleys on it and then to the lathe which also has a 4 step pulley.
I have more speeds than I need with several duplicates but it does come in handy. The lowest speed is 87 rpm and the highest is 6000 plus.
Re: Problem Solved! Tumbler works!
Allen Neighbors
>I was talking to a friend about trying to set up this system, and, to make a long story short: He gave me a continuous duty, Dayton geared motor, that turns 60 RPM.
I mounted it and the arbor on a piece of plywood that clamps to the bench, for use.
There are two pulleys on the arbor, opposite the chuck, that give me 33 or 41 RPM.
Re: Arbor front side
Allen Neighbors
>I have to move the Arbor when I change speeds (if it becomes necessary, when setting up).
This shows one bolt (threaded into tee-nut) holding the frontside of the Arbor, and the other bolt to be used if I change speeds.
Re: Arbor back side
Allen Neighbors
>This shows the other two bolts. One holding the Arbor, and the other on to use if I change speeds.
I'll try to figure out something to reverse the rotation. It may involve a larger base board, so I can turn the Arbor around with the Chuck toward the back.
Anyway, thanks to my friend, it's ready now.
And many thanks, TD, for this idea. :o)
Allen
now just go get some lava rocks
TDaniel
>and give er a spin. You can get a bag of lava rocks at HD or Lowe's. Most everything else they have is now made in China or south of the border but their lava rocks are still US made :)
TD
Re: Does it work well enough?
gil jones
>Thanks, Terry.
Re: now just go get some lava rocks
Allen Neighbors
>I've been using pea-sized granite gravel from my wife's carport. It's gravel that came from a granite quarry in Oklahoma. TXDOT also uses it, along highway shoulders. It's sharp edged, and works pretty well.
I'll try the lava rock, if I can find any small enough.
Thanks, TD.
TD
Bob Fawcett
>why not mount the whole tumbler so you can tilt it forward or backward. This would shift the rocks to one end or the other for those forms that need it.
Way to go Allen
Bob Fawcett
>You can size your lava rock with a hammer. :-)
I did
TDaniel
>and it helps but it cannot be tilted far enough for flat topped pieces. Maybe I need to re-work the stand. This started out as a cheap, simple thingy and now is getting complex and a potentially expensive machine. That is what I love about this hobby :)
Re: Bob, thanks a lot...
Allen Neighbors
>...for trying to help me on this thing. I think I'm going to try one of those small motors on another tumbler.
I'm dreaming of making one that rocks, front to rear, so that it rocks one direction during about 40 or 50 revolutions of the tumbler. Then, back the other way, during the next 40 or 50 revs. Just thinking about it.
:o)
Re: now just go get some lava rocks
Karl in IA
>You might try some 'chicken grit.' It's small sharp gravel they feed to chickens. Comes in different sizes as I recall.