Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

HELP!! (TD or other Genius Minds)

Posts

HELP!! (TD or other Genius Minds)

#1

HELP!! (TD or other Genius Minds)

Allen Neighbors

>I have an arbor that I have rigged up to hold my four-jaw chuck, in order to smooth the inside of hollowforms with gravel. I have a two-speed 1/3hp motor that turns 1725 and 1150 RPM with a two inch DRIVE pulley.

That leads me to these RPM Reduction Questions:

Situation Number One: I want to connect the motor to the Chuck arbor which has a 2" DRIVEN pulley, and reduce the arbor speed to 35 to 40 RPM. (Due to the cast iron shroud on this arbor, it's not possible to enlarge this pulley, either. However, I may be able to attach a larger pulley on the opposite end of the chuck.)

I think it will be necessary to use an intermediate axle/arbor to make such a reduction in RPM.

If I can't enlarge the arbor drive pulley, what size pulleys will be required on the intermediate axle, since one will be a DRIVEN pulley and one will be a DRIVE pulley?

Situation Number Two: If it is possible to attach a larger pulley to the opposite end of the Chuck Spindle, what would be your suggestion as to pulley sizes?

Room to mount this contraption is not a problem.

Allen

Re: HELP!! (TD or other Genius Minds)

#2

Re: HELP!! (TD or other Genius Minds)

Bob Fawcett

>Allen,

To get your 1150 down to 50 you need a 23 to 1 reduction. This would mean a 46" pulley driven by your 2". You could split this up with one or more jackshafts. If you had 10" driven pulley on the jackshaft, and another 2" driving another 10" for the arbor, that would give you 25 to 1 reduction and shoul yield 44.2 rpm.

Re: HELP!! (TD or other Genius Minds)

#3

Leo Van Der Loo

Re: HELP!! (TD or other Genius Minds)

Leo Van Der Loo

>Hi Allen, it's straight dividing Allen, if you have to go from 1150 to 40 its (28.75) 29times, so in one step your driven pulley would have to be 2X29=58" if you can use a flat belt and go to a 1"driving pulley on the other side of a jack shaft then you can halve the 58" to 29", if you can thaalso halve the size of the motor drive to 1" than the 29" can also be halved to 14.5"

if you can use two jack shafts then you can divide all those numbers depending on the sizes used.

With the flat belts, I mean those like serpentine belts, they can drive much smaller pulleys than V-belts

I hope I didn't confuse things for you.

Have fun and take care

Leo Van Der Loo

Re: HELP!! (TD or other Genius Minds)

#4

not even close to genius mind.

john lucas

>You guys make my head hurt. That's too much thinking for me. :) I'll just try to cut or sand the inside of my vessels.

Re: HELP!! (TD or other Genius Minds)

#5

Re: not even close to genius mind.

Allen Neighbors

>John, I've been turning some hollowforms with a 1/2" hole. I can see inside them, and don't like the tool marks. I can't sand the inside of those... thus the need for a tumbler.

Re: HELP!! (TD or other Genius Minds)

#6

Re: HELP!! (TD or other Genius Minds)

ERWIN NISTLER

>What is this about puting sand in a vessel to smooth it??

Do you use the stuff that is used in a rock polisher??

Have you considered making a couple temporary rings for the hollow form so it can be put on a rock polihser? Seems to me that must be the correct speed whatever it is.

Re: HELP!! (TD or other Genius Minds)

#7

Re: HELP!! (TD or other Genius Minds)

Allen Neighbors

>Bob, I really appreciate your doing the math for me. I got confused when I looked at the information on the net.

I've imagined my grinding/polishing table with a 46" pulley. :o) ROFL

And I do have a jackshaft prepared, to go between the motor and Chuck Arbor.

I'm pretty sure that I can turn a hardwood pulley to mount on the end of the Chuck Arbor, that will take the slow RPM.

But that leads me to another question for you: If I turn a 10" pulley out of hardwood, will it take the RPM of the jackshaft?

Re: HELP!! (TD or other Genius Minds)

#8

Re: HELP!! (TD or other Genius Minds)

Allen Neighbors

>Yep. Confused is the word. :o) That's why I posed the question here... because I got confused trying what I learned from the net.

Re: HELP!! (TD or other Genius Minds)

#9

Light bulb!

Bob Fawcett

>Make a couple of plywood rings that could hold the form. You could mount the chuck on large dowel at the center of one ring. You could connect the rings with 3 or 4 dowels evenly spaced around the outside attached with screws. Your spindle could become a roller for one side. Add roller and sit the rings between the rollers. Now the spindle drives outer edge of the rings. This would give reduction based on diameters of the spindle and the rings.

Re: HELP!! (TD or other Genius Minds)

#10

Re: HELP!! (TD or other Genius Minds)

Bob Fawcett

>Jackshaftt will run at 5 to 1 reduction, so 1150 / 5 gives 225rpm. I don't see why not.

Re: HELP!! (TD or other Genius Minds)

#11

Re: HELP!! (TD or other Genius Minds)

Allen Neighbors

>Erwin, I've thought of that, but I don't have a polisher. Plus, it would require additional rings for each separate form. I have all this other stuff on hand, except for the pulleys.

I have 1/2" and smaller granite gravel in one carport, and it works well in the inside of these small forms.

Re: HELP!! (TD or other Genius Minds)

#12

Re: HELP!! (TD or other Genius Minds)

Allen Neighbors

>Thanks, Bob; this is almost like a chatroom!!

I'll get to it. If I get it worked out, I'll post a pick.

Allen

Looking forward to Pensacola.

Re: HELP!! (TD or other Genius Minds)

#13

Re: Light bulb!

Allen Neighbors

>I haven't got a clue what you just said. :o)

Re: HELP!! (TD or other Genius Minds)

#14

Al, find one of these

gil jones

>This one (of mine) drops 1725 to 160 rpm


img

Re: HELP!! (TD or other Genius Minds)

#15

Re: HELP!! (TD or other Genius Minds)

Allen Neighbors

>Bob, something I found on the net mentioned belt length. What does that have to do with the RPM?

Re: HELP!! (TD or other Genius Minds)

#16

Re: Light bulb!

Bob Fawcett

>I just turned your setup into a tumbler like the jewelry tumblers.

Maybe my crude drawing will help.


img

Re: HELP!! (TD or other Genius Minds)

#17

Re: HELP!! (TD or other Genius Minds)

Bob Fawcett

>Nothing that I can think of. Just needs to wrap around the pulleys correctly.

Re: HELP!! (TD or other Genius Minds)

#18

Re: Al, find one of these

Allen Neighbors

>That'd be a-ok, but I'm trying to cobble this thing together with what I have on hand. You know the feeling... got an idea... got started... want to finish... don't want to wait for UPS. :o)

Re: HELP!! (TD or other Genius Minds)

#19

Re: Light bulb!

Allen Neighbors

>Okay, I understand now. But how do I figure the RPM, based on the size of the tumbler and the size of the dowels?

Is one of the dowels driven by the motor shaft? Or by a tire mounted on the shaft? (I so have some old rollers that are bearing mounted.)

Re: HELP!! (TD or other Genius Minds)

#20

The easy way *LINK*

Bob Fawcett

>I know you said you don't want to wait on UPS, but check this.


Slow gear motor

Re: HELP!! (TD or other Genius Minds)

#22

Re: Thanks, Bob and Everyone...

Allen Neighbors

>Bob, due to the size of that motor, and others I checked out, I think it would be harder to adapt that to my chuck, than to go the way you've helped me with.

I think I'm going to turn a couple of hardwood pulleys tomorrow morning. :o)

Thanks for all your help.

Thanks to everyone. :o)

Re: HELP!! (TD or other Genius Minds)

#23

Re: Thanks, Bob and Everyone...

gil jones

>Try this.....


img

Re: HELP!! (TD or other Genius Minds)

#24

Re: Light bulb!

Bob Fawcett

>Drive is the spindle shaft itself if it is exposed and long enough. If not a dowel or roller driven by the motor. The edge of the drive spindle drives the edge of the tumbler roller. Speed is the ratio of the diameters of the 2. If the spindle is 1" diameter and the tumbler is 12", you have a 12 to 1 reduction. You could glue or tape some sandpaper to the drive roller if needed for traction.

Re: HELP!! (TD or other Genius Minds)

#25

gearbox

TDaniel

>Al, check with any maintenance department at local plants. They always have gearhead units from old conveyors and outdated machines. Also you might find them at flea markets or salvage stores. Anything from 10 to 1 up to 50 to 1 will work. You can alter the output rpm by using pulleys to go up or down in final rpm. Also, don't overlook an old treadmill for a source of a vs unit. Mechanical or electronic speed control will work. The final shaft will turn so slowly that you can use oil soaked oak or maple or whatever for bearings.

TD