Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Treadle lathe problems

Posts

Treadle lathe problems

#1

Treadle lathe problems

john lucas

>I got a 1 1/4" wide leather belt today. I installed it on the lathe after turning a crown on the large wheel. It won't stay on. The wheel does wobble a little but not much. I'm thinking about adding more wood to the outer rim of the wheel. 3/4" on each side. If I do that should I crown the whole outer diameter or should I try to form a lip to keep the belt on. I remember old farm machinery only having a crowned wheel but the belts were usually wider.

Re: Treadle lathe problems

#2

Re: Treadle lathe problems

Ron in Drums PA

>I have some old book binding equipment that originally ran from overhead pulleys and leather belts. Right now it still has a leather belt and an electric motor mounted underneath. The pulley is crowned and the leather belt is 1-1/4" wide.

Hope this helps

Re: Treadle lathe problems

#3

Re: Treadle lathe problems

Don Henthorn

>Heck, John. That is a bummer. Are both wheels crowned? That is a no no. Otherwise I would think that it has to do with the alignment of the wheels.

Re: Treadle lathe problems

#4

Re: Treadle lathe problems

albertabob

>My bet(not having seen it) is that the wheels are not co planar.

Try running a level on the sides of both to see if they line up.

Think about the wheels on your bandsaw.

p.s. The crown wont help you if the belt material is too hard.

Bob

Re: Treadle lathe problems

#5

Re: Is this the lathe you're....

JamieDonaldson

>...bringing to TACA this weekend? You could substitute a bicycle crank and sprocket assembly and have a multiple speed foot powered lathe!

Re: Treadle lathe problems

#6

Wheel not co-planar

Dominic Greco in Richboro PA

>John,

I think Don and the others have hit the nail on the head.

I've run into this situation before. But on leather belt driven treadle lathes but land based arresting gear (emergency runway gear). The company I used to work for never had rims on their runway edge sheaves. The centerline of the lead off sheave (an massive 8" diameter machined alum deal) needed to be aligned with the centerline of the runway edge sheave. If they were off by just a bit, the 8" wide nylon tape did not track. This could be a real problem when trying to stop a F-16 from heading off the end of the runway and into who-knows-where! But once they were aligned, and the correct tape tension applied, it tracked perfectly every time.

You may need to shim the shaft of one of the wheels, and perhaps even check the balance to see if that may be throwing it off a bit.

Good luck.

See ya around,

Dominic

Re: Treadle lathe problems

#7

Re: Treadle lathe problems

ben d.

>John'' I have a couple pictures that I took of a hand powered lathe in a museum in Vermont this past week. It was not set up for use and behind some other stuff but you can see how the drive was made. The drive pulley or wheel was lipped on the driver and the driven was flat.

Excuse the picture quality.


img

Re: Treadle lathe problems

#8

Re: Treadle lathe problems

ben d.

>pic #2


img

Re: Treadle lathe problems

#9

Keith Tompkins

Re: Is this the lathe you're....

Keith Tompkins

>And, the audience could really participate...by taking turns pedalling.

Re: Treadle lathe problems

#10

Re: Is this the lathe you're....

john lucas

>It is and it's really fighting me. It's too late to make it bicycle crank. I only have two evenings left to work on this thing.

Re: Treadle lathe problems

#11

Re: Wheel not co-planar

john lucas

>Dominic I think that may be the problem. That and the wheel being too narrow. I'm working on widening the wheel but I found out my miter saw wasn't even close to correct on the 22 1/2 degree setting. it's dead on for 90. I've been doing test cuts on the table saw miter jig. Everything is fighting me. I took a known accurate 45 degree triangle, marked on the table. Then I took a compass and divided this in two. Should have given me dead on 22 1/2. Not even close. I've already readjusted the gauge 1/4". Now I'm really close to nailing it but I can't see how could have been that far off. I had to quit for the night before I cut off a finger.

Re: Treadle lathe problems

#12

Re: Wheel not co-planar - 22-1/2 degrees

Carol from AZ

>Hey John,

For really dead on accurate angle set-ups in a nano-second, get yourself a clear adjustable draftsman triangle. Less than $20. No muss. No fuss. No calculating. They are getting harder to find, however. Super well supplied office supply store. Or the 'net.

Carol, wo loves inexpensive accurate tools.

Re: Treadle lathe problems

#13

Leo Van Der Loo

Re: Treadle lathe problems

Leo Van Der Loo

>John, for a band aid kind of thing, you could make a fork and screw that onto your lathe to keep the belt from coming off for now, they used to have those on machinery for switching between drive and idle, and/or reverse with a second flipped belt, all this on a rod with a movable handle that would steer the belt from one to the other pulley.

If you want to align the pulleys later, you should be able to shim the wheel bearing up/down and move forward/backwards, also sideways, thats where the oversized holes in the bearing stools were handy for.

Just a thought I had the other day, is that, if I were to use a treadle lathe I seriously would consider a way to keep the stored energy in the fly wheel, so one would not have to stop and restart that wheel every time you wanted to have a look at the turning.

Have fun and take care

Leo Van Der Loo

Re: Treadle lathe problems

#14

Re: Wheel not co-planar - 22-1/2 degrees

john lucas

>Carole I've tried all kinds of gadgets and angle gauges over the years and find that I still have to fine tune. That's why I built this new sliding table miter guage. Once I get the angle perfect and measure it with the dial micrometer I should be able to duplicate angles exactly. unfortunatly I haven't found a way to calculate the angles accurately enough for the first cutting.

Re: Treadle lathe problems

#15

Re: Treadle lathe problems

john lucas

>Sounds too complicated for now but How about a lever actuated idler for the belt? That wouldn't be too hard to build. You could get really fancy and add an electro magnetic clutch for the drive wheel. I'm not sure that's very traditional however.

Re: Treadle lathe problems

#16

Re: Treadle lathe problems

Bob Fawcett

>John,

I built a belt sander that uses a 2" x 72" belt. There are 2 large wheels (think of these as your drive wheels). They are made from large industrial wheels with solid rubber tires with a slight crown. There is a third idler wheel that is a 2" wide skateboard wheel. This wheel has a screw adjuster that allows me to adjust it in the plane of the belt. This is my "tracking" adjustment, similar to the way a bandsaw adjusts. Maybe you could add a third wheel with a similar tracking adjustment.

Re: Treadle lathe problems

#17

Brad Vietje

Ben -- Which Museum ? Shelburne ?

Brad Vietje

>

Re: Treadle lathe problems

#18

Re: Wheel not co-planar - 22-1/2 degrees

Ron in Drums PA

>I just took a closer look at my equipment when I got into work this morning..

The belt is 1" wide.

The top pulley is crowned and is 1-3/4" wide x 11" diameter. The crown is very slight. If I lay a straight edge on the pulley, I only see about a 1/32" gap on both sides.

The bottom pulley has "walls", the pulley rides in the center and is 1" wide x 1-1/2" diameter.

The two pulleys are perfectly aligned

Re: Treadle lathe problems

#19

Re: Treadle lathe problems

John Lucas

>Thanks bob. I've thought about some adjustment to the wheel like a belt sander adjusts tracking or the way a bandsaw wheel tilts but that would be hard to build in this late in the game.

Re: Treadle lathe problems

#20

Re: Wheel not co-planar - 22-1/2 degrees *LINK*

Mike from St. Clair Shores

>John,

If you need to figure out exact angles in the future, The Beall Co. sells a vernier protractor and it is dead nuts for accuracy.

Mike


Beall Vernier Protractor

Re: Treadle lathe problems

#21

Re: Treadle lathe problems

Wilford Bickel

>John,

As told above- your quick fix for this weekend is the fork. Think of a tuning fork mounted to keep the belt tracking onto the wheel. You can put one at where it goes on the wheel and one where it comes off. Quick and easy to build and mount - just mark it and cut it out with band saw or jig saw. Years ago when I worked with flat belts in the Textile industry we also had a sticky black stick of belt dressing we put on the leather belts. This also kept them from coming off and added to the pull they gave.

Re: Treadle lathe problems

#22

Re: Ben -- Which Museum ? Shelburne ?

ben d.

>Thats where it is at. Just what building I don't remember but it was in the center part of the area. There was other " stuff " in the building and the lathe looked out of place there.

Re: Treadle lathe problems

#23

Re: Treadle lathe problems

jmohnike

>John I had a similar problem with a tredal lathe. If I had too much tension on the belt it would come off, If I had too little it slipped.

While I was standing next to the lathe uttering a string of not so nice words because it was slipping my 7yr old son said "Why don't you wrap sandpaper on it". I thought about it and decided to give it a try, and wraped the H/S with 80 grit. It worked! True the belt wore down faster but I would rather replace a belt from time to time than to be frustrated for hours on end.