Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Voids that I do not fill

Posts

Voids that I do not fill

#1

Leo Van Der Loo

Voids that I do not fill

Leo Van Der Loo

>Sometimes we fill voids and splits and cracks, but other times leaving them as they are just looks better.

I had some very figured hard maple that on one end was being eaten by an army of wood worms/grubs, and I made a couple of small bowls out of that part as well as the rest of the wood.

Turning and picking grubs and part grubs as I went along, also from the wall and the lathe etc, even just about eat one, then cleaned all the eaten and digested and redeposited wood out of the wood, sanding is a challenge as the sandpaper likes to grab and rounds the crisp edges, so careful handsanding and powersanding only in spots.

The wood being solid in one half of the bowl and hardly any wood on the other side doesn't make for easy smooth turning, however I did get it finished without any chunks being plucked out.

This bowl is about 9"X3" and I put some pure tung oil on it and buffed it a bit very carefully.

Have fun and take care

Leo Van Der Loo


img

Re: Voids that I do not fill

#2

Leo Van Der Loo

Re: Voids that I do not fill 

Leo Van Der Loo

>


img

Re: Voids that I do not fill

#3

Leo Van Der Loo

Re: Voids that I do not fill 

Leo Van Der Loo

>


img

Re: Voids that I do not fill

#4

JL

Re: Definitely a good reason to wear a (long)

JL

>face mask. Splat! OK. It's a pretty piece - it's even art. A few voids I can understand. They are an embellishment to the piece - sort of like fretwork.

Where do you draw the line though? How do you judge if it is worth your investment in time or whether you should just toss the chunk of wood? Do you take an awl and see how sound the piece is?

I have seen some marvelous pieces made out of punky wood with glue to stabilize the wood. Where do you draw that line?

I mean it's not like anyone has X-ray eyes and can see when a particular chunk has marvelous grain inside.

What determines when a piece of wood goes on to the trashpile (or compost heap) and when it's worth the effort and time to turn?(General question for everyone).

Re: Voids that I do not fill

#5

Re: Voids that I do not fill

George Van

>Leo, you make my woodpile look better with each post! You definately earned this one.

Re: Voids that I do not fill

#6

Re: Voids that I do not fill

Mike from St. Clair Shores

>Leo,

You made me sit up and take a closer look the other day at that apple graft burl, now this one. Are you ever afraid that they will blow apart? I'm definitely going to try some of the wood I usually toss in the firewood pile. You always seen to make these pieces turn out so nice. Keep em coming.

Mike

Re: Voids that I do not fill

#7

Leo Van Der Loo

Re: Definitely a good reason to wear a (long)

Leo Van Der Loo

>Hi JL thank you for your reply.

Where to draw the line ?, you got to keep in mind this was half a large log, and already cut a bunch of too soft wood away, I already had started to cut up the wood into blanks, and the whole log was very figured wood, I had already suspected that, even before I pulled some bark off, then there was spalting, all that ads up to a hopefully nice looking turning.

Experience and gut feeling also play a role, also being able to pull it of, and having FUN are a big reason to do it.

Where to draw the line ?, if it will fall apart or it looks bad are reasons not to proceed, or even start, and deciding the first is easier than the second, but again you have to go with your feelings IMO.

Have fun and take care

Leo Van Der Loo

Re: Voids that I do not fill

#8

Leo Van Der Loo

Re: Voids that I do not fill

Leo Van Der Loo

>Hi George.

George, I really have a lot of fun when I get wood like this, you cut a piece off that is almost to bad to even burn, (was one of the reasons I did get this wood, the firewood cutters did not touch it, it looked that bad initially) and pull it off to make a nice turning from it.

This bowl and the little black ash bowl have already been purchased for Christmas giving.

Have fun and take care

Leo Van Der Loo

Re: Voids that I do not fill

#9

Re: Voids that I do not fill

Allen Neighbors

>I'm with you, Leo. If it's pretty wood, turn it, and if it tries to fly apart, wire it together, or tape it together, or tie it with string... but make a turning, and it'll be worth it. Gut feelings work well, most of the time, but sometimes it doesn't. But don't throw it away if it's pretty wood, and not too punky, until you try.

Beautiful wood. Nice form. Well done bowl. Thanks for posting it.

Allen

Re: Voids that I do not fill

#10

Leo Van Der Loo

Re: Voids that I do not fill

Leo Van Der Loo

>Hi Mike, Thanks Mike

Funny that you should ask this, as this came up just the other day, I have never YET, knock on wood, had a turning blow up on me, I have caught and pulled a chunk out of some turnings, have them come loose and get damaged hitting the tool rest and anything else in /on their way out, and bouncing around the shop, but never had them fly apart on me.

Mind you my big lathe now and before were relatively slow turning lathes, but I am careful and speed has not been high on my list when turning, most of my turning is done in the 300 to 1000 rpm range, mind you that even those speed can be to high, for certain sizes and wood qualities.

It pays to look-listen and be alert while turning( some of this is getting harder to do as the look/listen devices are deteriorating ), and look and think before you start, keep it safe.

Have fun and take care

Leo Van Der Loo

Re: Voids that I do not fill

#11

Leo Van Der Loo

Re: Voids that I do not fill

Leo Van Der Loo

>Thanks Allan

YES you said it Allen, if it has a chance to look good give it a chance.

And You're right, gut feelings do serve us well, listen to it.

Have fun and take care

Leo Van Der Loo

Re: Voids that I do not fill

#12

JL

Re: Thanks

JL

>