Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

screeching banjo

Posts

screeching banjo

#1

screeching banjo

eliot d

>I have a Powermatic 3520A. When I slide the banjo, it makes a really annoying high pitched screeching sound. Can you help me get rid if it? I usually clean the lathe bed and underside of the banjo with WD 40, which I rub in with a scotch type pad.

Re: screeching banjo

#2

Re: screeching banjo

W.C. Turner

>I also have 3520A. Besides WD40, I also use Johnson's Paste wax.

Re: screeching banjo

#3

Re: screeching banjo

Rick Allen

>Boneshield

Paste wax

Pledge wipes

Anything to make the surface slippery. Treat both the ways and the bottom of the banjo.

It could be that the bottom of the banjo isn't flat. Sliding the banjo could cause the uneven bottom of the banjo to... On second thought it doesn't matter as any of the lubracants listed will take care of the screech.

Good Luck

Re: screeching banjo

#4

Re: screeching banjo

Jim Swank

>You can also use soapstone as a lubricant. It's normall used for marking stuff for welding.

Re: screeching banjo

#5

Re: screeching banjo

Mike from St. Clair Shores

>Since you've already tried WD40, another thing to consider is the amount of play when you loosen the banjo to move it. I've adjusted the nut on the bottom of the banjo to loosen it up because the way it came from the factory was too tight.

Mike

Re: screeching banjo

#6

Re: screeching banjo

Jim Pugh, Elyria, OH

>A slightly different response and one that I do in additon to the various lubricants (I use WD-40 most of the time) is to take the banjo off of the lathe, lay it upside down, get a fairly fine file and file all edges of the bottom surface. Just run your fingers around gently and you will find plenty of sharp edges. Do inside edges, outside edges and any other edges that might be there. It is then a good opportunity to spray/wipe the entire bottom surface with the lube of your choice, including the shaft that runs from front to back. Now, it may not be less screachie (?) but I'll bet it will slide easier.

Re: screeching banjo

#7

Re: screeching banjo

Pete LaBelle

>My new JET 1642 does the same thing. Looking at the castings, they are hollow and only have the sidewalls contacting the bed, rather than a wide surface. You're getting the same effect of pushing an upside down paper cup sideways across the table. Lube has helped mine, along with lifting it slightly as I slide it. Makes a nice lathe sound cheap, unfortunately.

Pete

Re: screeching banjo

#8

Re: screeching banjo

eliot d

>Thanks for all these responses. I'll try filing the edges of everything and some of the lubricants you have suggested. I don;t have the feeling that anything is too tight, though. But I'll look at that too.

Re: screeching banjo

#9

Play fiddle, guitar and bass loud in the

Jim K in Trappe PA

>background. It will sound fine.


img

Re: screeching banjo

#10

Re: screeching banjo

Bill Crommett

>Be carefull how much lubrication you get on the ways or you will find trouble getting the tilstock to stay in place.

Re: screeching banjo

#11

Re: Play fiddle, guitar and bass loud in the

Bob Fawcett

>I got to see Vassar Clements this year shortly before he died.

He was one heck of a fiddle player, and will be sorely missed.

Re: screeching banjo

#12

Re: Play fiddle, guitar and bass loud in the

eliot d

>Jim K, I'm surprised that you're the first to pick up( ha!) on the obvious banjo - sound screech thing . Good one!