Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

**PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

Posts

**PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

#1

Ellis Walentine

**PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

Ellis Walentine

>



GRAMERCY TOOLS FINISHING BRUSHES



Tools for Working Wood is pleased to announce the introduction of Gramercy Tools finishing brushes. Hand-made in New York, these exceptional brushes are perfect for shellac, varnish, lacquer and other wood finishes.

The Gramercy Tools brush is made of 100% fine European ox hair -- the best material around for finishing brushes. It will leave a virtually brush-mark free surface and will hold a generous amount of finish for a long, efficient and controlled stroke. The brush is solid hair with no gap, so you can cover carving details and moldings, and go over edges and corners with no drips or splatters. The ox hair is anchored in the brush with epoxy, so the brush won't deteriorate in solvents. The ferrule is top-quality stainless steel so you can easily clean it in any solvent, including water, and not have to worry about corrosion -- which can shorten the life of an ordinary brush and contaminate your finish. The handle is made of unfinished hardwood in an attractive, traditional beaver-tail pattern that is very comfortable in the hand and has a great balance. The brush has a hand-sculpted chisel tip for best performance. With care, our brushes will last for years and make finishing much easier and far more rewarding.

Brushes are available in three sizes: the 2" wide brush is the most generally useful, the 1" size is good for localized details, and the 3" size will make doing a large surface easier and quicker. Bristle length is 1 3/4" on all three brushes. Click here for details.

We tested a lot of materials in designing our brush. Click here to read about our testing and see a film of our brush being made.

Contact us for more information about our brushes and other products, or to request a catalogue...

Tools for Working Wood

toolsforworkingwood.com

(800) 426-4613






Gramercy Tools Finishing Brushes

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

#2

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES

Carole Valentine

>Darn it! I just can't go that site without learning something! Today I learned not only about brushes, but all about rasps and rifflers!

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

#3

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES

Bill Hale / woodspinner

>Ellis

I hope you are getting a bunch for this add.

I for one do not like to see an add on this forum site. It is about questions and answers not advertising.

My feeling - Put it in clasified !

Bill in Casa Grande, AZ.

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

#4

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES

Walter Ahlgrim

>Bill

How do you think Ellis pays the bills for this website? Did you pay a subscription fee to get your pass word? The least we can do is to click on the sponsors links and view there products. The Classifieds are for noncommercial use only. Were did your get a free lunch today?

Walt A

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

#5

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES

Mike from St. Clair Shores

>Keep em coming Ellis. If you are able to secure some money for these ads by all means do so.

You have set up an awesome site and just remember "You're the Man". Anyone who thinks they have a right to complain about this should find another site to visit. In todays world everything is expensive and your time is also valuable. I appreciate all that you have done and please don't let the Nay-sayers get you down. I think your understanding about what is right or wrong for this site has surpassed any and all of my expectations. If someone doesn't want to read a post they can skip it. How hard is that.

Thanks for all you do.

Mike

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

#6

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES

Carole Valentine

>If I had to pay for lessons to learn all that I have learned from the questions and answers on this FREE site, Bill, I would not even be turning because I wouldn't be able to afford it. Ellis requires nothing from us other than civility to one another. It costs a considerable amount in time and money to run this site. Many of us try to pay him back a little through benefit auctions, donations or buying a sweatshirt or other mechandise once in a while. If he can make a little profit (which I have no idea if he does or not), good for him! He puts "Paid Ad" in bold type in the subject line so it's really very easy for you to just skip the few ads, but what's the harm in looking? Just my two cents worth.

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

#7

Re: **MY ERROR

Bill Hale / woodspinner

>Sorry all

I guess I made a wrong supposition. I thought the advertising section was where the income came from. Sponcers and advertising page and I do look at it.

Even though I must be in a minority I still do have to say I don't like it mixed in.

Bill in Casa Grande, AZ.

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

#8

They also have a terrific holdfast

Craig Daymon

>They make probably the best bench holdfast I've seen. Pretty reasonable too.

Why should a turner care? Well, if you're also a carver, they are very useful. But also, I was over a friend's house last weekend roughing down some Ash with the chainsaw and I was holding the pieces on his Workmate while he trimmed the end hanging off the Workmate. A couple of holdfasts would have kept my fingers a lot farther from the chainsaw. (No, no injuries to report.) Anyway, my friend ordered up a set this week and they arrived next day. It will certainly make things easier for him next time I'm not around.

-Craig

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

#9

Re: They also have a terrific holdfast

William Duffield, on the Cohansey

>Joel's new bowsaw looks like it will be a real winner too. A lot of thought and experience has gone into this one. This recommendation is from someone who has built his own bowsaw and uses it regularly.

BTW, Joel Moskowitz has always been a valuable contributor to the WC HandTool Forum, offering a plethora of sage advise and commentary over the years. Most Tuesday nights you can also discuss tools with him on the Hand Tool Chat. If you are at all into antique hand tools, don't miss the non-commercial side of his website, the Museum of Woodworking Tools.

I'm a "More than satisfied" customer of Tools For Working Wood. I also like to think I do my bit to make WoodCentral a success, or at least to keep it running a smidgen more smoothly. But what I, or any of the other volunteers, contribute means nothing if the paid advertizers aren't here to keep the lights on.

At the very least, you can rest assured that Ellis's advertisers are reputable and offer quality products and service. If you are unsure about whether those products will meet your particular needs, phrase your questions lucidly, and post them on whichever WC forum you feel most at home.

Addy Protocol: I make a few of my own woodworking hand tools, and I sometimes sell them. I also work for, sell tools for, and teach woodworking skills for, a franchisee of a competitor of Tools For Working Wood. My employer is a retailer, not a manufacturer.

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

#10

Ellis Walentine

That's okay

Ellis Walentine

>Sorry, I missed this thread when it first developed, but now I would like to offer a rationale -- call it a defense -- of paid messageboard ads.

As someone mentioned, I rely on advertising to pay some of the bills around here. Also, we do not allow commercial posts on our boards, with the exception of Classifieds, which is off-limits to businesses. (I know we have had some cheaters, but I can't pay any more attention to it than absolutely necessary.) Often, an advertiser has a unique, time-sensitive deal or opportunity that he/she wants to put in front of our group. It might be the announcement of a new product or a closeout on a discontinued item or a special purchase or something that doesn't lend itself to a standard banner ad, which may run for three months or more. The messageboard ad is the perfect solution.

As Carole mentioned, I produce the ads myself, as tastefully as possible, and identify them clearly as ads, just so people who don't want to be sold to can avoid them. Incidentally, I screen these ads, too, so you won't see ads for junk or non-endemic stuff like mattresses or self-help courses. :-)

The amount I make on one of these ads is almost negligible, but I regard it as a service to advertisers and visitors alike. As long as I don't start loading up more than one or two such ads a day--which is really unlikely because I don't have the time to create them--I would hope you could endure having them here.

It's legitimate to have preferences, suggestions and complaints. I listen to them all, because that is what ultimately makes WoodCentral a better site.

Cheers,

Ellis

Re: **PAID AD** GRAMERCY TOOLS FINISHING BRUSHES *LINK*

#11

Old saying...

Ron McKinley

>"He who pays the fiddler calls the song." Works for me........Ron