Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Homemade Hollower

Posts

Homemade Hollower

#1

Homemade Hollower

Allen Neighbors

>I made this tool today, to hollow a sassafrass form. 1/2" hot-rolled steel bar, 1" deep 15/64" dia hole in the end to accept a 3/16" HSS tool bit, and an intersecting 13/64 hole tapped for a 1/4" setscrew. It fits in my Don Pencil handle. (The 3/4" shaft that came with the Don Pencil rig wasn't quite small enough to go in the hole in the form.)


img

Re: Homemade Hollower

#2

Re: In the Don Pencil Handle 

Allen Neighbors

>


img

Re: Homemade Hollower

#3

Any issues with hot roll...?

Bob Fawcett

>I always think I should go find cold rolled steel. It probably would make no difference, but I can't say I have tried either or both.

How do you like Don's handle?

The only hollower I have is a Sorby hollowmaster. I haven't done that much hollowing yet, but I am not sure I like what I have. Probably just a matter of practice. It is too large for a lot of the smaller things one might hollow though.

I have been eyeing a Oneway termite.

I should go ahead and make a few. I have all of the tools to make one, but not the steel or cutter. Those are cheap.

Re: Homemade Hollower

#4

Sorby hollowing tool

Mike Nelson

>I Don't know about hot or cold rolled, but I have 'blown up' a few small opening hollow forms with the curved end flat sided 3/4" Sorby! When that flat edge catches on the mouth of a HF, look out. Another time I was careful not to touch the rim and still got a move it or lose it catch! Come to find out, the cutting blade was contacting the left side of the HF while that flat curved edge touched the right side...not a good thing.

Re: Homemade Hollower

#5

Re: Any issues with hot roll...?

Allen Neighbors

>Bob, I made all my tools prior to attending the gathering in April, and all that time I thought I was buying cold rolled steel. The dealer I've always bought from told me recently that he didn't seel cold rolled... only hot rolled.

As far as I know, there's not a problem working the hot rolled. I've never had any, unless it's an occasional broken bit. When that happens, I just cut off the end, and start the hole over.

I like the Don Pencil rig, especially that it comes with the adapters to fit other, smaller tool shafts. However, I've begun my captured hollowing system... (If my welder ever gets back from wheat harvest). Sometimes the Pencil rig doesn't like my ribs, when I use the boring bar.

Re: Homemade Hollower

#6

Re: The Sorby Hollowmaster is .....

Jamie Donaldson

>a....about as useful as belt loops on a snake when it comes to real hollowing! It's too big, too grabby, and too short.

Re: Homemade Hollower

#7

Re: Never saw the Sorby,

Allen Neighbors

>but I think to do large hollow forms the Don Pencil rig is a little light, also. I love it for smaller forms, such as Christmas ornaments, etc., but without the elbow brace. Sometimes when I use the elbow brace on larger forms, I get hit in the ribs with it.

Is the Sorby Hollowmaster the same style as the DP?

Allen

Re: Homemade Hollower

#8

Re: Never saw the Sorby,

Wilford Bickel

>Hasiak told us in his demo at SSS that the problem with the Sorby was when they copied the Stewart system they let the cutting tip go past the center line of the straight part of the shaft. Don Pencil and the Stewart rig both keep the cutting tip in line with the center line of the straight part of the shaft and you do not encounter as much torque or the problem of catches as with the Sorby. Makes sense if you look at it from a physics standpoint - this was the main reason I purchased the Pencil system after the symposium.

Re: Homemade Hollower

#9

Re: The Sorby Hollowmaster is .....

Barry Turner

>Uhhhh........probably. It is good for getting your feet wet on hollowing.....then making you realize its shortcomings as a hollowing tool.

Re: Homemade Hollower

#10

Re: Homemade Hollower

Mike from St. Clair Shores

>Allen,

How hard was it to bend that 3/4 stock. I like the tool you made, but I'm a little paranoid about that arm brace. I've included a pic of a hollower I've made. This is my small one.

Mike


img

Re: Homemade Hollower

#11

Re: Homemade Hollower

Mike from St. Clair Shores

>Here's a pic of my medium one. I sure would like to try to make the piece like you did for the end on this one. I can change the 3/4 tool holder. I think I will try to bend one like yours.

Mike


img

Re: Homemade Hollower

#12

Re: Homemade Hollower

Allen Neighbors

>Mike, the pic above is a 1/2" shaft. However, to bend the 3/4" isn't any harder.

I used a vise to hold it, and my Bernzomatic (sp) torch to heat it, to red glow, and then put it into a hole in my anvil, and bent it. I also could have just flipped it around in the vise and bent it.

Once it's heated, it's easy to bend. And it will still be hard enough to use as the tool shaft it's intended to be.

Allen

Re: Homemade Hollower

#13

Thanks, I'm going to give it a try.

Mike from St. Clair Shores

>

Re: Homemade Hollower

#14

Re: The Sorby Hollowmaster is .....

Bob Fawcett

>I think I agree. I am not an experienced hollower, but I have not had much good luck or experience with it.

Re: Homemade Hollower

#15

Re: Homemade Hollower

Stuart Johnson

>Allen, How do you make the bends?

Re: Homemade Hollower

#16

Re: I used a Bernzomatic

Allen Neighbors

>torch. I put the end in a vise just to hold it while I heated the other end. When I got it red, I took it out of the vise, and stuck the hot end in a hole in my anvil, and bent it. You can use the vise instead of an anvil. Then I cooled it in water, and heated the other spot for the next bend, and so on. It was easy. You can do it. Just get the steel and do it. This one was 1/2". On larger metal, just heat it more, and use a little more pressure to bend it, or use a hammer.

Hope this makes sense.

Allen

Re: Homemade Hollower

#17

Re: Homemade Hollower

Allen Neighbors

>Mike, that's really a nice looking hollowing tool. How does it work for you? Do you notice much vibration of the laser?

Is it pretty easy to hold while your using it?

I've seen that style, but don't remember where it was, and wondered about it.

Allen

Re: Homemade Hollower

#18

Re: The Sorby Hollowmaster is .....

Duane C.Leach

>My Sorby Hollowmaster works just fine now that it has a new and much longer and heavier handel on it.

Happy tuning.

Duane

Re: Homemade Hollower

#19

Re: I used a Bernzomatic

Rick Bane

>Hey Guys,

I'm new to turning but my backround is in metal. I would cold bend. I have a manual bender that I have bent 3/4in solid with no problems. I have also bent stainless for a friend of mine that does paintless dent removal. The benders are available at Harbor Freight. Thanks Rick

Re: Homemade Hollower

#20

Re: Harbor Freight Bender

Allen Neighbors

>What do they look like, Rick?

Re: Homemade Hollower

#21

Re: Duane, did you make

Allen Neighbors

>your own new handle? How about a photo?

Allen

Re: Homemade Hollower

#22

Re: Homemade Hollower *LINK*

Darrell Feltmate

>Nice tool. For a little different perspective, I have some instructions for making hollowing and other tools, including an arm brace, on my web site. Just go to the tool making section and follow from there.


Darrell Feltmate's Wood Turning Page

Re: Homemade Hollower

#23

Re: Homemade Hollower

Allen Neighbors

>Hi, Darrell. Nearly everything I've learned about making turning tools I've picked up from you. You da Man!!

Allen