Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Powermatic 3520B remote switch

Posts

Powermatic 3520B remote switch

#1

Powermatic 3520B remote switch

Charlie Anderson

>I think I hooked it up according to the manuals schematic.

Now only the remote switch has any control over the lathe. The push/pull switch can be in any position and the remote switch works.

It this right?

Re: Powermatic 3520B remote switch

#2

Re: Powermatic 3520B remote switch

Gary Ljostad

>Hello Charlie. The way mine works is; When both switches are in the on position, ether one can turn the lathe off. When you turn the lathe off with the remote switch, it can not be turned on with the main switch, only the remote. When it is turned off with the main switch the remote can not turn it on. I normaly leave the remote on and use the main switch to control the lathe when I am woking in front of the lathe. For bowl turning and if I turn from the back, or on very long or big pieces I use the remote. I find the remote very usefull when teaching, like the instructor peddles on drivers ed' cars. ;-)

Re: Powermatic 3520B remote switch

#3

Re: Powermatic 3520B remote switch

Charlie Anderson

>That sounds logical, so obviously you're hooked up differently than I am. My push pull switch has two blacks and no whites attached.

I'm hooked up as shown on page 40 of http://www.wmhtoolgroup.com/partfiles/m_1352001.pdf

Re: Powermatic 3520B remote switch

#4

Re: Powermatic 3520B remote switch

Doug Thompson near Cleveland

>It should work like Gary discribed. The push/pull switch has two wires going to it, one from the for/rev switch and the other from the speed control. Double check the wiring, you'll splice into the wire from the speed control.

Hope this helps.

Re: Powermatic 3520B remote switch

#5

Re: Powermatic 3520B remote switch

Charlie Anderson

>That makes sense but I don't read the schmatic that way. I currently don't have any white's connected to the push/pull switch. That would account for it not having any effect.

I have the white from the potentiometer, the white from the remote switch and the blue connected by a wire nut.

I probably need a pigtail from the wirenut to the push/pull switch.

I'll rethink it in the morning.

Re: Powermatic 3520B remote switch

#6

Re: Powermatic 3520B remote switch

Gary Ljostad

>As I read the diagram, when the lathe is new there should be a blue going to the Push/pull switch, and another wire (doesn't show color)that goes from the FWD/Rev switch to the Push/Pull switch. To add the remote switch you take off the blue and connect it to one of the wires from the remote switch, and connect the other wire from the remote to the termanal on the push/ pull switch where the blue was connected. So you end up with a blacks and another wire, (no whites)going to the push/pull switch. This is how mine is connected and works as I stated above.

Re: Powermatic 3520B remote switch

#7

Re: Powermatic 3520B remote switch

Mike from St. Clair Shores

>I have the 3520A and when I wired my remote, I just cut the blue wire and attached the switch wires to the two sides of the blue. This then lets the remote work only if the main red pull is in the pulled out on position. I think this should be the same on the B.

Good Luck,

Mike

Re: Powermatic 3520B remote switch

#8

Re: Powermatic 3520B remote switch

Doug Thompson near Cleveland

>Maybe I need to rethink what was said... Totally disregard my last post it is WRONG. Sorry to cause any problems.

Re: Powermatic 3520B remote switch

#9

Re: Powermatic 3520B remote switch

Charlie Anderson

>Well, I almost had it right yesterday. Funny how one wire in the wrong place can make a difference.

Anyway, thanks to all for helping me straighten my thinking.

Works great now.