Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

5 Barn Photos

Posts

Re: 5 Barn Photos

#26

Hosting limits?

Carole Valentine

>Appears you have exceeded the limits of your picture hosting service, Dom. Send them to Ron to post on the site.

Re: 5 Barn Photos

#27

Re: WorkMutt

William Duffield, on the Cohansey

>I hope someone posts some photos from 5ive Barns of my WorkMutt 400 with the custom WorkPittBull jaws. I got lots of comments from people who thought this was a great idea and were going to do the same thing to theirs.

I have been very frustrated with my B&D WorkMate for several reasons. It seems like it should be a very useful and flexible portable bench, but it has several very frustrating problems. First, the dog hole diameters are non-standard, and the non-standard plastic orange dogs provided are really difficult to use. Second, the dog holes are never in any convenient places, either with respect to each other or to anything you might want to get a grip on. Third, the tops are made of some sort of termite barf with only a thin veneer of hardwood. This stuff has no weather resistance.

I had been meaning to upgrade mine to something useful for quite some time, but hadn't gotten the "round-tuit", until I left it out in the rain last month. The particle board tops swelled up, warped and split like germinating lima beans. Since I use this thing for holding all sorts of small power tools, including a JET mini lathe, a small belt/disk sander, a slow speed grinder, a scroll saw, a Pana-Vise, etc., both in the shop, and especially when I'm working away from the shop, I needed to do something in a hurry.

I'll offer a few tips I learned for anyone else who might be considering this enhancement.

I made the new jaws from 8/4 hard maple. Finished thickness ended up 1-7/8". You can make the jaws wider than the originals, and you can make the rear jaw deeper, extending it towards the back of the bench as far as you want. I think you would find 4 to 6 inches wider and a few inches deeper to be useful, assuming you have 8/4 hardwood stock available. The depth of the front jaw and the positioning of the support blocks with respect to the mating surfaces of the jaws shold not be changed, however. I made my front jaw a bit deeper than the stock jaws, but then had to cut it away to provide clearance for the cranks. Also, when closed, both jaws tend to lift where they meet, so the mating surfaces have to be beveled slightly so they will close completely at the top. It is best to measure the closure angle and bevel them after you have mounted and tightened them up, to get the right amount of bevel. Also, note that since the rear jaw is reversible, the faces of the rear jaw should be at 90� and all of the bevel applied to the front jaw.

Each of the four plastic blocks that provide the interface between the top and the base need a 13 mm. hole drilled in the bottom of the tops. You will need a 13 mm. drill bit to make these! This hole doesn't need to be drilled all the way through the top as B&D usually does it. That just provides an extra place for dust to load up. I found that the hole for the bolt needs to be 7/8" diameter, and should be drilled through to 1/2" from the bottom of the jaws.

You can't have too many dog holes. Make sure the holes in the front jaw line up with corresponding holes in the back jaw. An unpaired hole, or row of holes, is useless. Think Swiss Cheese. For reference, check out the Veritas carving bench.

Extra dog holes are really useful, as we discovered yesterday, for dropping turning tools into. Measure the front jaw travel, and make the front-to-back dog spacing in both jaws just a little smaller than this value. Also, make sure that the lateral spacing can accommodate the width of the tools you need to hold on top of the bench. Dogs must line up with the feet of the tool or you will have to mount the tool to a piece of plywood that fits your dog hole spacing.

I found out it is easy to drill lots of 3/4" dog holes in hard maple if you have the right Forstner bit. I used a BorMax bit. If you are not very, very careful about your rpm, feed rate, and keeping the chips cleared, cheap Chinese Forstner bits quickly overheat, turn blue, lose their temper, get dull, stop cutting and burn the wood.

After fitting everything and drilling all the dog holes, I chamfered the edges of both jaws and also the tops and bottoms of the dog holes, using a router and a 45� chamfer bit with a bearing.

I'm still working on hardwood dogs for the dog holes, and am using Veritas Bench Pups and a WonderDog in the interim. I haven't tried a holdfast in the dog holes yet, but 8/4 hard maple should be sufficient. I also need to cut v-slots, both horizontally and vertically in the jaw faces, for gripping round stock. Also I need to put some Waterlox on it for protection and to minimize warping with changes in humidity.

I'll probably drill some more holes to hold other turning tools that don't fit the dog holes (big skew chisel, roughing gouge, mallet) or that drop right through (Nova Midi Chuck tommy bars).

Re: 5 Barn Photos

#28

Re: Wholesale Tools has $25 minimum order.

Al Crandall (NE of Indy)

>Hi Bill. I'm lucky to have a WT store 1/2 hr away from me, so I have bought from them across the counter. Their catalog states, on the inside front cover, that there is a $25 minimum order on phone orders so you need to build your wish list to reach the minimum.

Re: 5 Barn Photos

#29

Re: So does MSC Industrial

William Duffield, on the Cohansey

>

Re: 5 Barn Photos

#30

Some More

Stephen Mushinski

>Ellis riding the rails with Bill taking notes!


img

Re: 5 Barn Photos

#31

The Entertainment

Stephen Mushinski

>Joanne Adler, Ellis Walentine, Dan Donaldson


img

Re: 5 Barn Photos

#32

I Can!

Tom Sweeney - Coatesville, PA

>Mike I have a great shot of nice streamers coming off that buckeye. I haven't had time to download my pics yet, but will post it when I do. You'r going to have to change your name to shavingmaker Mike :-)

Re: 5 Barn Photos

#33

Re: You can't prove it

Frank of Mantua

>well the name is Frank, But gentleman I get accused of a lot of things but gentleman ? ////

No problem I was enjoying that I could be of help.

It was a very nice day with a lot of very nice people. I know I am looking forward to next year.

Re: 5 Barn Photos

#34

Seems OK for now

Dominic Greco in Richboro PA

>I logged into the photo hosting site sometime this morning and noticed the problems. When I logged back into WC just now it looks like the photos are back. I have no idea what's going on with that Free Pic Hosting site.

See ya around,

Dominic

Re: 5 Barn Photos

#35

Whoops! Spoke too soon!

Dominic Greco in Richboro PA

>There they go again. I'll upload smaller versions to WC as soon as I get home tonight.

See ya,

Dominic

DOH!...Stupid pic hosting site!

Re: 5 Barn Photos

#36

Re: 5 Barn Photos

don in central IL

>Is anyone else not seeing the photos? I'm getting an out of space error message. I have a cable modem and have not had problems prior to seeing images. Maybe something wrong on my end?

Re: 5 Barn Photos

#37

Paul Porter

Dom, try this hosting site... *LINK*

Paul Porter

>...they will let you host up to 500 photos.


Free photo hosting

Re: 5 Barn Photos

#38

Reposting of pictures

Dominic Greco in Richboro PA

>Sorry about that folks. The pictures were so popular that we overloaded the free pic hosting site I use. So here are the same pictures, just dropped down in resolution so that they conform to the 60K file size limit.

See ya around,

Dominic

Steve Antonucci at the Vega lathe



img

Re: 5 Barn Photos

#39

Pic 2

Dominic Greco in Richboro PA

>

Turning on the Poolewood, Dustmaker Mike Larvia



img

Re: 5 Barn Photos

#40

Pic 3

Dominic Greco in Richboro PA

>

Ron Sardo and Lee Schierer



img

Re: 5 Barn Photos

#41

Pic #4

Dominic Greco in Richboro PA

>

Tyler Howell with Tom Sweeney in the background




img

Re: 5 Barn Photos

#42

Pic #5

Dominic Greco in Richboro PA

>

Tom Sweeney at the Poolewood Lathe



img

Re: 5 Barn Photos

#43

Pic #6

Dominic Greco in Richboro PA

>

Bill Grumbine "holding court"



img

Re: 5 Barn Photos

#44

Pic #7

Dominic Greco in Richboro PA

>

Mike Rubes and Ruth Niles



img

Re: 5 Barn Photos

#45

Pic #8

Dominic Greco in Richboro PA

>

Myself and Ruth Niles



img

Re: 5 Barn Photos

#46

Pic #9

Dominic Greco in Richboro PA

>

Col George Dart and William Duffield



img

Re: 5 Barn Photos

#47

Pic #10

Dominic Greco in Richboro PA

>

Walt Drummond, Dan Donaldson, and Warren MIckley



img

Re: 5 Barn Photos

#48

Pic #11

Dominic Greco in Richboro PA

>

Bill, Moses Yoder, and Joanne Adler



img

Re: 5 Barn Photos

#49

Pic #12

Dominic Greco in Richboro PA

>

Ellis at the sharpening station



img

Re: 5 Barn Photos

#50

Re: Pic #11

Joanne in Pt. Pleasant, PA

>The gentleman with his back to the camera is Robert "Limey" Bolton. Although, he'd probably quip that he is no gentleman. lol. This guy is a hoot and really is a gentleman. He was giving me a demo of how he sharpens plane blades and very kindly sharpened my jointer plane blade (thanks, Limey!). Thanks for the pix, Dom. I was too busy having fun and learning things to take any. Sorry folks.