Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Dividing Heads/Plates

Posts

Dividing Heads/Plates

#1

Dividing Heads/Plates

Greg Deavers

>Was wondering if you all would help me out with a technical issue.

I naievely searched for the above before asking and am not the answer.

I need to be able to cut splines/teeth on a wooden gear (similar to segmenting- 36, 48, 62 teeth etc.) depending on the spec requirements.

Could anyone suggest how I would be able to do this with high accuracy? Need to do this as inexpensively, and simply as possible with a "few accurate jigs"....... is this possible.

Understand divider heads, etc - expensive & slow... Any other methods of work, or tricks???

Thank you for your commentary!

Greg

Re: Dividing Heads/Plates

#2

Re: Dividing Heads/Plates

John Lucas

>I have the perfect thing that I just put together. I will set it up and take a photo later tonight. It is a plastic index plate that I bought for $16 and then built a jig for the lathe to hold my router. I don't have more than $25 dollars in the whole thing because it was made out of scrap wood.

Re: Dividing Heads/Plates

#3

Look forward to your ideas John -Thx!

Greg Deavers in Stillwater

>

Re: Dividing Heads/Plates

#4

Re: Dividing Heads/Plates

john lucas

>Here is a shot of the whole rig. I built the box to support the router and it's completely adjustable so I can rig up fences at almost any angle act as guides for the Dewalt trim router. The index plate is is a kind of nylon plastic, quite tough. I bought it from Ironfire inovations. It was $19, Iquoted you wrong earlier, $22.10 with shipping. You have to build some sort of system to hold the index pin in relation to the lathe. They give you plans in with the index wheel but I decided to make a perminant (sp) installation on the poweratic 2035. I clamped the block to the index wheel and drilled 4 holes through their holes to match the index holes. then I put the wheel on the lathe and installed 2 index pins into the block to align it. I used double stick tape on the back to lock it in position. Then I removed the wheel and drilled 1/8" holes Through the wood and metal for 1/8" press pins. I drilled and tapped the bottom hole on my lathe but that was a hassle and a waste of time. I think the press pins with the double stick tape will hold it quite easily. If you drill the holes all the way through you can knock the pins out if you need to remove everything.


img

Re: Dividing Heads/Plates

#5

close up of router and gear

john lucas

>I used a 90 degree v groove router bit and chose 30 teeth. You could of course do a lot more or less. The index wheel has anything up to 60 index points.


img

Re: Dividing Heads/Plates

#6

index alignment block

john lucas

>Notice the magnet on the far left in the photo. This holds my index pins. The index wheel comes with one. I made a second so if I loose the first I'll have a standby.


img

Re: Dividing Heads/Plates

#7

finished gear.

john lucas

>OK this isn't great but it only took 37 minutes from the time I went out to the shop till the time I got back. That included unlocking cabinets, finding the router bit and installing all the stuff on the lathe. One thing to consider when cutting gears is grain orientation. Side grain teeth will be week unless very large. Plywood or homemade plywood with cross grain construction is best.


img

Re: Dividing Heads/Plates

#8

Re: Dividing Heads/Plates

Mike from St. Clair Shores

>Greg,

I just read all the post by John Lucas and I was thinking that this is probably one of the reasons that WC is number one in my book. He not only answered your question, but supplied all the necessary info like the supplier, prices and photos to show how to make the jig. Thanks again to John and all the others on this forum that so often are able to share their knowledge and expertise with us.

Mike

Re: Dividing Heads/Plates

#9

Re: Dividing Heads/Plates

Greg Deavers in Stillwater

>Hi John,

Your assistance is fantastic. Would like to chat more offline if possible at your convenience. I tried to find "Wildfire Innovations" and had no luck. Would like more info on their plates, equipment etc.

Have been looking at divider heads with plates and have no real idea how I would put a system together accurately for shaped shaped teeth, or even just pins, etc..... Pretty new at this part of it.

Thanks for your courteous response!

Greg

Re: Dividing Heads/Plates

#10

meant "Ironfire"

Greg Deavers in Stillwater

>

Re: Dividing Heads/Plates

#11

Re: Dividing Heads/Plates *LINK*

john lucas

>Sorry about that I should have put a link up but sometimes the ole brain doesn't work. Feel free to e-mail me anytime. You never know when someone will fire up this ole brain and a brand new idea will slip out. I am working on 2 more ways to get indexing to the powermatic but haven't had time to implement them yet.


http://www.ironfirellc.com/shop/

Re: Dividing Heads/Plates

#12

Re: Dividing Heads/Plates

john lucas

>I forgot to mention that one our club members just built his own indexing system for the Jet mini. It works on the same principal, that is being installed between the chuck and lathe. He made it out of aluminum and just stepped off the holes with dividers and drilled them. The put a plate on top of the lathe with holes in it to align everything. Simple and easy to make. Sturdier my not as versitile as the Ironfire plate.

I am currently building an index system for the Jet mini that's really nice and easy to build. I should have it done by the end of the 4th holiday. I'll post that when I'm done.

Re: Dividing Heads/Plates

#13

Re: Dividing Heads/Plates

Greg Deavers in Stillwater

>Thank you John, I appreciate everything you have done to help me get started on this one! I look forward to your post.

I am just not sure I could mfg my own accurately enough as a purchased one. What do you think?

Sincerely,

Greg Deavers