Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Gasket material for vacuum chucks

Posts

Gasket material for vacuum chucks

#1

Gasket material for vacuum chucks

Dick Gerard

>Other than the thick black stuff from OneWay, does anyone out there use something different? I have been playing around with the packing material used for chin, plates, glasses, etc. you get from U-Haul (ala David Lancaster). But you go through that stuff very quickly. Sometimes a single bowl is all you get and then you have to remove all traces of the old material, use spray adhesive on the new, let it get tacky, put it on, clean the edges and the interior and start again. There has to be a better material that is not as expensive as the OneWay black rubber stuff.

Re: Gasket material for vacuum chucks

#2

Re: Gasket material for vacuum chucks

Mike from St. Clair Shores

>Last year I attended a Dave Hout seminar and his suggestion was to use fake chamois material that comes in large sizes. Its fairly inexpensive and I have been using it and I think it works great.

Re: Gasket material for vacuum chucks

#3

Re: Gasket material for vacuum chucks

Bart Rhoads

>I use the Foamys or Foamies that you find in the craft section at Walmart. They are 8 x 11 sheets very inexpensive and they wont leave black marks on you pieces. They have an adhesive backing also.

Re: Gasket material for vacuum chucks

#4

Re: Gasket material for vacuum chucks

Jennifer@Indy.USA

>Hi Dick,

I don't have a vacuum chuck but I hear that stuff called Fun Foam that you can buy at hobby and craft stores works great. It comes in sheets like paper...only it's thick like foam rubber.

Thanks for the nice comments on my platter :)....and yup I'll be at the meeting.

Jen

Re: Gasket material for vacuum chucks

#5

Re: Gasket material for vacuum chucks *LINK*

Phil Joines Krum, Texas

>I use a gray 3/16" thick closed cell PVC sheet with an adhesive backing from MSC. It comes 54" wide at $8/foot. When it gets damaged the remainder peals off prity easily.


foam sheet

Re: Gasket material for vacuum chucks

#6

Re: Gasket material for vacuum chucks

john lucas

>Dick before I bought some real vacuum gasket material from a guy in Georgia I used the foam stuff you put on your truck to seal the topper. It wears out but does let you get through quite a few bowls first. It only comes in 2" wide strips but I've found you can put a little clear silicone on the joints between strips and it will work fine. The good part is you get a huge roll for about $5.

Re: Gasket material for vacuum chucks

#7

Re: Gasket material for vacuum chucks

Barry Irby

>I went to a commercial gasket wholesaler and bought some black neoprene foam gasket material. I got 1/8" and 1/4". I am using the 1/8" and have not gotten to the 1/4", although I think I am going to make another drum chuck for bowl that were turned green and warped a little. The stuff does not leave a black mark and is fairly tough and cheap enough. I think I have twenty bucks in two pieces about a yard square. If you find such a place, ask for scraps or offcuts. What they consider a scrap might suit you just fine and they may give it to you or sell it cheap.

Re: Gasket material for vacuum chucks

#8

Re: Gasket material for vacuum chucks

Ron in Drums PA

>I also use the craft foam others mentioned. I found some 1/4" at Micheal's (craft store). Works well at less than a $1 for a 8x11 sheet.

Re: Gasket material for vacuum chucks

#9

Re: Gasket material for vacuum chucks

Stuart Johnson

>Another vote for Foamies (Wal-Mart). It also works very well when used to cover the edge on a compression or donut chuck.

Re: Gasket material for vacuum chucks

#10

Re: Gasket material for vacuum chucks

Bill Grumbine (Kutztown PA)

>Dick, I've been using the electronics packing foam too, and recently one of the guys in our club passed on a tip he had come up with. He uses a rubber band and pulls the foam back around the edges. No glue to mess things up, slow things down, or melt the foam if you stick it on too soon. I could not find a rubber band big enough, so I pilfered some elastic hair ties from my daughters' hoard.

I keep meaning to get some of those foamies from Walmart, and it should be easy since the womenfolk are there several times a week, but I never seem to remember when they ask if I want anything at the store.

Bill

Re: Gasket material for vacuum chucks

#11

Bob Moffett

Re: Gasket material for vacuum chucks

Bob Moffett

>I use router pad bought from Woodworkers Supply. It is tan and comes in sheets. I cut a sheet and put a hole in the center of it and place it between the bowl and chuck. It last a long time and the price is reasonable. I talked to a friend of mine and he uses old mouse pads.

Re: Gasket material for vacuum chucks

#12

Re: Gasket material for vacuum chucks

Tony Shaftel

>I bought a square yard or so of 1/8" closed cell neoprene from mcmaster.com. I'm still using the first cut out circle. It is offered in various grades of firmness and was reasonably priced.

Re: Gasket material for vacuum chucks

#13

Wet suit material

Eddie Pacheco, San Jose, Ca.

>That's what I've seen used around my area with good results. Buy and old kids or adult wetsuit, the foam is 3mm thick for a light suit and 6mm thick for a heavier suit. The foam material is very durable and one suit will yeld a lot of various size gaskets.

Re: Gasket material for vacuum chucks

#14

Re: Gasket material for vacuum chucks

Phil Axtell

>Hi all,

Has anyone tried using silicone calk? I saw a demo some years ago where the demonstrator cut a groove and inserted a 3/8" bead of silicone calk. Thjen he trued up the calk after it hardened with a gouge. He said it was easy, cheap, and quick to repair or replace.

What do you all think?

Phil Axtell

Re: Gasket material for vacuum chucks

#15

Re: Wet suit material

eliot

>I bought the One Way expensive neoprene, which works fine. But I was given a tip by David Lancaster at the last AAW meeting to use that stuff that electronics are packed in because it produces a WEAKER seal, which Lancaster prefers because he wants to reposition the bowl, which you can't do with the good stuff (short of turning off the pump). I have to disagree for two reasons:(1) I had a failure with the electronics stuff; (2) there are better ways to provide easy repositioning, such as a little rubber squeeze valve that you make yourself.

Members of my club are using surgical rubber tubing. They cut it lengthwise and fit it over the rim of the cylinder. I forget how they seal the place where the two ends come together -- probably some kind of flexible sealant.

Re: Gasket material for vacuum chucks

#16

Re: Whenever I talk vacuum with people, I tell

Al Crandall (NE of Indy)

>Whenever I talk vacuum with people, I tell them to install two tees in their system someplace. One is for a vacuum gage and the other is for a ball valve which is plumbed to the atmosphere to create a controllable leak. This allows for easy positioning and easy removal of the piece when done. I experienced a situation where the piece wouldn't release and I had to get the wrenches out to break a fitting to release the vacuum.