Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Tool cart Question?

Posts

Re: Tool cart Question?

#26

Re: Tool cart Question?

Dominic Greco in Richboro PA

>Barry,

Some time a couple years ago, I posted a similar question. From the input I got, I built my lathe tool holder and cobbled together my rolling tool cart. The cart was picked out of the dumpster at work and was outfitted with some similarly discarded workbench drawers. Later I installed an MDF counter trimmed in red oak. The wall mounted rack holds all my turning tools (for now), while the rolling cart hold my chucks, vacuum chucking equipment, right angle drill, and sharpening center.

In the picture posted here, you can see the wall mounted tool rack on the left hand wall, with the cart on the right. When I need a tool, it's within easy reach of the lathe.

See ya around,

Dominic


img

Re: Tool cart Question?

#27

Tool cart pic

Dominic Greco in Richboro PA

>In this photo you can see the tool cart better. However, this was taken before I added the workbench drawers underneath.


img

Re: Tool cart Question?

#28

Re: Tool cart Question?

Steve in NC

>Dominic

Are you using the floppy disk boxes to store sanding disks? I have been doing this for a while and it works great.

Steve

Re: Tool cart Question?

#29

Re: Tool cart Question?

Philip Duffy

>Gosh, if I was that organized I would never get anything done!

Re: Tool cart Question?

#30

Thanks

Barry Irby

>Thank you to everyone who took time to post pictures and make suggestions. I'm still thinking and designing. I'll keep an eye peeled at various dumpsters, but the problem for me with the guys that found parts in the trash is that its not very "reproducible", even though back in the day when they let you drive out into the dump I used to come home with more stuff than I took. I'm trying to convince myself to add on to my shop, but this cart would be a good addition either way. It just gets more and more complicated as I consider all the possibilities and suggestions. Thanks again.

Re: Tool cart Question?

#31

Oh yeah!

Dominic Greco in Richboro, PA

>Steve,

What else am is one supposed to do with old floppy disk holders? :>)

In another life I was the IT manager (along with several other titles) for a small company. I had these cases all over. I couldn't figure out what to do with them once CDs became so prevalent.

Then I noticed that they were like little file cabinets. Complete with dividers I could label and sized perfectly for sanding disks! The 3 1/2" cases were for my small sanding disks, while the 5 1/4" (yeah,...I still had some of them around) holder was used to hold 6" sanding disks.

See ya around,

Dominic

Re: Tool cart Question?

#32

Re: my tool cart.. Do you use all

Stuart Johnson

>John, It looks like you have close to 50 tools between the cart top and the wall. What percentage do you think you use on a regular basis.

FWIW, most of my tools are held in a 5 gallon paint bucket with holes cut in the top. Each hole is labeled, scraper, skew, bowl etc., so I can easily find the correct one.

Re: Tool cart Question?

#33

Re: my tool cart.. Do you use all

John Lucas

>Stewart I have about 75 or more tools. I've been turning for over 20 years and love tools. I like to play with the different grinds to learn from them. I use all of the ones in the front and side rows regularly. The ones on the back row are specialty made tools for hollowing or cutting unusual cuts.

My favorites are a 3/8" sorby bowl gouge, 3/8" Packard spindle gouge,3/8" off brand spindle gouge with really shallow grind, 1" Sorby oval Skew, 1/2" flat scraper, 1/2" oval scraper, Henry taylor 1 1/2" heavy bowl scraper, a whole bunch of parting tools from 1/4" down to 1/16.

Re: Tool cart Question?

#34

Re: Tool cart Question?

Steve Lewis

>Here's my set-up. The tool-cart and lathe shelf are made from MDF. The balast box is a copy of Dominics'.


img

Re: Tool cart Question?

#35

Re: Tool cart Question?

Ned Bulken

>without reading all of the responses, the first onethat comes to mind for me is the 'Ultimate tool stand' which was published in american woodworker a few years back. Google it and you can still get the online version of the article. I think it might be what you're looking for.