Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Coring- Oneway vs Mac, Donna/Robo

Posts

Coring- Oneway vs Mac, Donna/Robo

#1

Coring- Oneway vs Mac, Donna/Robo

Bud

>Or anyone else that would like to chime in, that has experience with both systems.

Between the Oneway and McNaughton; I have gotten some mixed signals from various sources, between the two systems as far as flexibility of core shapes. Some say that the McNaughton may give a bit more flexibility in the shape of the cores-but NOT much more. It was suggested that the Oneway could core at different angles to give either a shallow or a deeper cone shaped cores. Is this true? Also, if you were only using the Oneway, and had to choose only 2 of the 4 knives, what two would you find to be the most useful.

Thanks Much, Turn safe

Re: Coring- Oneway vs Mac, Donna/Robo

#2

Re: Coring- Oneway vs Mac, Donna/Robo

Phil Powell

>I have the Oneway coring system with knives 1 thru 3. It's very easy to use and adaptable

to just about any bowl blank you can set in front of it. I find myself using knives ! in 2 most often. Those two knives can handle 90% of the bowl blanks I prepare. Oneways coring

system is expensive but the expense is off set by ease of use and the safety built into the design of the system. It has payed for it's self many times!

Re: Coring- Oneway vs Mac, Donna/Robo

#3

Re: Coring- Oneway vs Mac, Donna/Robo

RussFairfield

>I think a lot of how we see the tools will depend on how and why we use them. There are those who use the coring tool as a means to remove the inside of a bowl more quickly and to save the wood for other uses. Others want to cut multiple bowls from a single piece of wood. There are still others who want to remove the core from tall vases and other shapes that are different from that of a bowl.

They both cut a circular arc in the wood. The McNaughton should be the more flexible because the Oneway cuts a captured arc about a fixed center point, while the McNaughton has no physical restrictions. The reality is that, for the SAME ARC RADIUS, there is little to no difference between them because you still have to push or pull the tool into the wood and remove the core after it has been cut.

The captured Oneway tool will cut a more accurate arc and a narrower slot than the McNaughton in the hands of an inexperienced user. It has been argued that the average woodturner can relate the narrower slot to making them closer together and realizing more bowls from a singkle piece of wood. That might prove true for the inexperiences user. In the hands of an expert, it doesn't make any difference.

The Oneway is easier to use because every movement is in a fixed path, and only requires setting it up and pulling on the tool handle to make a cut. It is possible to core a bowl the first time.

Since the tool is both guided and powered by the person standing behind it, the McNaughton is more difficult to use and it takes more time and pracrice to learn how to use it well. I doubt that most woodturners will cut a successful core the first time they us the McNaughton tool.

The big difference between them is that the McNaughton has no physical restrictions on the arc of the tool. That means that the McNaughton's tool can have a very large atc, or can be straight, both of which are impossible with the Oneway.

The McNaughton is also cheaper than the Oneway, simply because there is less there.

If I were only turning salad bowls, I would have selected the Oneway because it is easier to use. I chose the McNaughton because there are more options available for less money, including large radius tools and a straight tool that would be impossible with the Oneway. I also have the additional option of making my own tools for the McNaughton. It is also important that I was willing to spend the time, and waste the wood, to learn how to use it. Someone else wwould have made a different choice for different reasons.

Re: Coring- Oneway vs Mac, Donna/Robo

#4

Well said, Russ!

David

>Very concise and points well taken. You have captured the essence of these two systems. The number of views when you post are consistently higher than most others because we know that you will be posting good advice.

Re: Coring- Oneway vs Mac, Donna/Robo

#5

Re: Well said, Russ!

robo hippy

>Well, a few things here. The arc taken is determined by the arc of the blade. The McNaughton blades are flatter than the Oneway, with the exception of the smallest blades. The largest Oneway blade has a tigher curve than the largest McNaughton. This makes the McNaughton better for taking cores from plates and tall cone shaped pieces. Because the McNaughton mounts on your banjo, you can come in from any angle, which does give you more options for more variety of shapes. The Oneway can move about 4 inches side to side, with most of the movement being towards the inside (about 3 to 1 inches), which is how you can get deeper cone shaped cores with it.

The cutter on the Oneway is 3/8 inch wide. It is the same on the McNaughton large set, and slightly less on the medium set, and less on the micro set. The kerf taken is almost exactly the same with all sets, including the Woodcut (the top of the Woodcut is concave which is interesting, but I have my doubts as to weather it makes any difference). The difference is the shape of the cutter. The McNaughton comes with a spear point on it, The 3/8 inch wide cutter removes a 1/2 inch wide shaving (2 long sides of the triangle). I grind my points down so that they are square. I had the old style of blades to start with, and heard about others experimenting with different profiles. They came with a bevel to the outside of the blade. I tried square, and bevel to the inside to see if it would help counter the drift, and profile didn't seem to make any difference at all. I didn't try a concave profile because I couldn't cut one like that. I setteled on the square profile because it made the cutter edge smaller resulting in less pressure as you cut. I may take one of the Oneway cutters and grind that point off to see if it makes any difference. They recently changed the profile so that the point has a bevel on it rather than a square point. This has to be their effort to counter the drift of the blades as they go in. The captured radius systems still experience drift, but because they are 'captured' it isn't as much of a problem as freestyle cutting.

As to which blades do I use the most, I seldom use the largest blades. Bowls over about 14 inches just don't sell that well for me. With the McNaughton, I use the 2 smallest baldes on the medium and micro sets for 99% of the cores that I take. Now that I have the Oneway, I use the #2 and #3 blades most of the time, and for the smallest cores, I always use the McNaughton micro blades.

robo hippy

Re: Coring- Oneway vs Mac, Donna/Robo

#6

Re: Coring- Oneway vs Mac, Donna/Robo

butter

>Thanks you guys for all the information on the coring systems. I order a oneway today.

Re: Coring- Oneway vs Mac, Donna/Robo

#7

Re: Coring- Oneway vs Mac, Donna/Robo

Donna Banfield

>It appears that you've made your decision. Everyone who responded, especially Russ Fairfield, gave you very good advice.

That's the beauty of this forum, isn't it?

Re: Coring- Oneway vs Mac, Donna/Robo

#8

Excellent ! Thanks much

Bud

>Thanks much All,, great detailed information to help a buyer make a wise decision to fit his/her needs!!

Turn safe