Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Finished Tilt Away Tailstock for PM

Posts

Finished Tilt Away Tailstock for PM

#1

Finished Tilt Away Tailstock for PM

Earl Eyre

>I recently asked for the pics of the tilt away I had seen and discoverd from Al Crandall that it was his. I built mine yesterday and today and here it is. Not as elegant as Al's so I might have to buy a can of Mustard Yellow paint so I can match it to the lathe. LOL

But it works great. I plan to reinforce how the ways are attached to the supports because I'm a little leary that the 9 screws will pull out of MDB. But it seems to be real secure.


img

Re: Finished Tilt Away Tailstock for PM

#2

Re: Finished Tilt Away Tailstock for PM 

Earl Eyre

>


img

Re: Finished Tilt Away Tailstock for PM

#3

3rd shot ofTilt Away Tailstock for PM 

Earl Eyre

>


img

Re: Finished Tilt Away Tailstock for PM

#4

Fantastic!

Jennifer@Indy.USA

>Earl,

You did a fantastic job with this! When are all of the lathe makers going to make this a standard feature? My tailstock is somewhat managable...but I know there's some out there that don't get removed out of the way like they should be, because they are too heavy. I know the Vicmark at Arrowmont that I turned on last summer was a huge pain.

Way to go Earl.

Jennifer

Re: Finished Tilt Away Tailstock for PM

#5

What I would consider doing...

david

>is reinforcing the horizontal wooden ways to the vertical elements perhaps with an aluminum angle in the middle through bolted to the ways above and one of the vertical supports. Just in case the pull-out resistance in the MDF does not hold those screws in. Also could partially close out the bottom section of the open end, which would give the box more rigidity. If you don't let the pivoting tailstock down gently, I hate to think what might happen to the assembly. Very nice job!

Re: Finished Tilt Away Tailstock for PM

#6

Good job. Man!Give you a few pics and away you go!

Al Crandall (NE of Indy)

>

Re: Finished Tilt Away Tailstock for PM

#7

Re: Fantastic!

Vicmarc.fan

>Jennifer,

There is a fix for the Vicmarc.

Ron


img

Re: Finished Tilt Away Tailstock for PM

#8

Re: Finished Tilt Away Tailstock for PM

Don Henthorn

>As I mentioned on another forum, wonder if I can find a big enough hinge to swing the extended bed and tailstock together on my mini Jet. Not that I am lazy, you know, just makes me tired removing them. (G)

Re: Finished Tilt Away Tailstock for PM

#9

Hey! That's a great idea.

Jennifer@Indy.USA

>

Re: Finished Tilt Away Tailstock for PM

#10

Thanks

Earl Eyre

>Thanks for the comments. I am going to take the pivoting mechanism off tomorrow are reinforce the ways attaching to the brackets as well as the bottom of the box in case I drop the tailstock as it goes down. In my case, if there is any way I can drop it I will! Hindsight, I wouldn't have used MDF, I just happened to have it so I was too cheap to go buy something else. For both reinforcements I will use some hardwood to make it as strong as possible.

Earl

Re: Finished Tilt Away Tailstock for PM

#11

Re: 3rd shot ofTilt Away Tailstock for PM

Mike Schwing from Md.

>Nice job Earl. I'm guessing you don't turn much off of the end, facing the spindle? I really like your idea but for me it would decrease the utility of moving the headstock towards the end for turning the insides of bowls standing at the end of the bed. If I ever used your idea for myself I can see one like you made but instead of tilting making it a rollaway.

Re: Finished Tilt Away Tailstock for PM

#12

Re: Finished Tilt Away Tailstock for PM

Barry Irby

>Nice job. Are your extended "ways" plywood or hardwood? I wonder if hardwood won't split and break if you drop the tail stock.

I made on for my Nova DVR. I used dome aluminum angle for the ways. That was a mistake. The aluminum "galls" when the steel slides on it and makes it tough to move. If you oil the aluminum or wax it, the lubricant transfers to the tailstock and it tends to slip on the bed, when it shouldn't.

Wouldn't it be great if the lathe manufacturers would sell us short pieces of beds to use for this purpose. I thought about contacting the repair center for Nova/Teknatool and seeing if they had a damaged one they would sell me cheap and let me cut it down.

I think here were complaints about Jet sending extensions that did not fit. Was It Jet?. If you could get your hands on one of those, you might be able to modify it to do this.

Re: Finished Tilt Away Tailstock for PM

#13

Re: Finished Tilt Away Tailstock for PM -Metal?

Stuart Johnson

>Any idea what it would cost a competent welder make one up? I'm not a welder but I know my Father could have made one up from scrap with no problem.

Re: Finished Tilt Away Tailstock for PM

#15

Re: Finished Tilt Away Tail stock for PM -Metal?

Barry Irby

>Good question. I think a machinist/welder could make one in a flash, pardon the pun. I made mine out of what I had at hand (aluminum and walnut) and with the skills and tools I have, Woodworking stuff. If the only tool you have is a hammer all your problems start to look like nails. (has anyone seen my 32 ounce fly swatter?) The "tilt away" for my lathe could have been very simple. A flat plate with two "ways" welded to it and a single metric bolt to hold it on. maybe I will use mine as a prototype and have a steel one made.

Re: Finished Tilt Away Tailstock for PM

#16

Re: Finished Tilt Away Tailstock for PM -Metal?

Jerry Whitaker

>Unless you know someone, the expense would probably be more than what you would want to pay. Here in South Texas, welders charge $55/hr. plus materials at whatever they want to price them and with a one/hour $55.00 minimum. By the time you pay for the materials, add the welding cost and then if you want the piece to look good and have them grind and polish, you could have bought a factory made extension.