Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Beading tools ?

Posts

Beading tools ?

#1

Beading tools ?

Pete in Holland, MI

>Any of you folks use bead forming tools ? This guy is struggling turning beads with detail gouges and skews on rims of bowls. Penn State has a new 4 piece set of HSS tools for $42. Not a Sorby, but probably adequate for my limited purposes.

Wondering if beading tools do in fact work, or if I'd be better to focus practicing with the skew & detail gouge?

Your thoughts ?

Thanx........

Pete

Re: Beading tools ?

#2

Steven Antonucci

I use a spindle gouge or a 3 sided point tool

steve antonucci

>Can't see spending the money on a tool with one use.

Steve

Re: Beading tools ?

#3

Re: Beading tools ?

Bill Grumbine (Kutztown PA)

>Hi Pete

Not only do I have and use a beading tool, I have the "git around behind tool" too, for when I am using my beading tool on captured rings for the goblets I turn.


I also use the beading tool for putting semi-circular feet on bowls.


However, for turning a bead on the rim of a bowl, a spear point scraper does a great job. I think the beading tools need too much clearance on the outside edges to get a good looking bead on the edge of a bowl. I have not seen the PSI set yet, so I have no comment on it one way or another, but for the price of one goblet or bowl, the set would be paid for, and it certainly makes things faster and easier.

Bill

Re: Beading tools ?

#4

Re: Beading tools ?

Bill Hale

>Make your own. I can get deeper with a beading tool than with a skew.

I also do not use a skew.

Good turning and be safe

Bill in Casa Grande, AZ.

Re: Beading tools ?

#5

Re: Beading tools ?

JKJ in East TN

>It would be nice to try before you buy, if possible. I bought a beading tool and I was disappointed. Compared to the clean cut of the skew, I got more tearout. The beads were more perfect than I could turn with a skew, though. Maybe it would work better on a harder wood.

JKJ

Re: Beading tools ?

#6

Re: Beading tools ?

John Lucas

>Pete I bought a beading tool and I made a beading tool. I prefer the skew for beads on spindles and a small spindle gouge for turning beads on bowls. I have tried the 3 point tool and it works pretty good but not as clean as the gouge. One trick I use when turning beads on the face side of the bowl is to raise the tool rest way up above center. It makes it easier to roll the gouge from top to side on the bead. On the side of the bowl this doesn't work.

Re: Beading tools ?

#7

Re: Beading tools ?

Ken Grunke from SW WI

>Pete, most people run into trouble when using a skew on a bowl, I sure do. The skew just isn't meant for bowl turning. A detail gouge with a pointy end would probably work best. I don't have one of those yet, but a skewchigouge is a good alternative and that's what I use.

Mine is shaped just like the front end of a kitchen spoon, and has a pretty long bevel when viewed from the side. It cuts like a skew, with the top face at about 10 o'clock or 2 o'clock depending on your direction of cut, and using the lower edge from the center of the tip down. Lot less likely to catch than a skew, because of it's curved edge. And easy to make and sharpen.

When sharpening, I put most of the pressure where the arrow is in the pic below, and grinding just a hair from the tip end on it's top face. That's so the tip's top face doesn't go below center, I just keep grinding back towards the handle and grind the bevel a little each time I sharpen.

I like this tool, you can roll a nice little bead with it or turn a small cove, even do hollowing with it.


img

Re: Beading tools ?

#8

Bob Moffett

Re: Beading tools ?

Bob Moffett

>Bill,

Are those interlocking rings on the goblet? How did you turn them?

Thanks,

Bob

Re: Beading tools ?

#9

Detail gouge and skew here

Carole Valentine

>I have one of those beading tools, but I don't think it gives me nearly as clean a cut. I have much more control with the gouge and skew.

Re: Beading tools ?

#10

Re: Beading tools ?

Mike from St. Clair Shores

>Pete,

You can buy a piece of 3/8 or 1/2" x 8" HSS from Wholesale Tool and make you own 3 point tool. It is a great tool and will cost you less than $5.00 to make.

Just my 2 cents,

Mike

P.S. if you e-mail me I can send you links. I think that there is a demo video on the AAW site.

Re: Beading tools ?

#11

This one really works... *LINK*

Peter Teubel

>I have a set of these Sorby Easy Beaders. They really work. While I usually turn beads with a skew or detail gouge, I find these tools supurb for really hard wood like cocobolo.


img

Packard Woodworks - Easy Beader

Re: Beading tools ?

#12

Ric Taylor

Re: Beading tools ?

Ric Taylor

>I was disappointed with my beading tools, until I started using them with a very light touch. Take your time, keep the edge sharp and let the tool work with very light cuts, and it will work fine. I use mine frequently now.

Ric

Re: Beading tools ?

#13

Re: Beading tools ?

Bill Grumbine (Kutztown PA)

>Hi Bob

The technique is fairly straightforward. I turn captive rings on the goblet, finish sanding them as far as possible. Then, I break one of the rings and glue it back together around the other one and the stem. Sound easy? It is when everything goes right. But, since I have big fumble fingers sometimes, I make it a habit to turn three or four rings on each stem, so that if there is a disaster breaking a ring, there are spares on which to fall back. If the first one goes well, I break and remove the spares.

I finish these goblets with Bartley's Gel Varnish. It dries to the touch quickly, so the chance of the rings sticking together or to the stem is minimized.

Bill

Re: Beading tools ?

#14

PDF of grind for skewchigouge on Woodcraft site

Craig Daymon

>The product page for the skewchigouge on the Woodcraft site has a link to a PDF file showing the grind with sharpening and usage information.

I bought one and find the tool very useful, but I would never buy one again as it is just too simple to make from a stock piece of rod. I've considered making a heavier one (the purchased tool has about 1/4" to 3/8" rod) out of maybe 1/2" to 5/8" diameter stock.

McMaster-Carr and MSC Direct both have M4 and A11 bar stock on hand in lengths up to, I think, 3 feet. The A11 is pricy, but the M4 isn't too bad comparing it to tools from M4.

-Craig

Re: Beading tools ?

#16

Re: Beading tools ? - - Thanx guys !

Pete in Holland, MI

>Always lots to learn with this hobby. Have a couple options I'm going to try. Seems many "forming" tools will work on harder woods, so long as they are sharp, and feed is minimal & steady.

Would love to have an expert to learn off some evening, but this site gives plenty of insite.

Thanx.......

Re: Beading tools ?

#17

Re: PDF of grind for skewchigouge on Woodcraft sit *LINK*

Ken Grunke from SW WI

>Craig,

Your best buy for HSS shaft to make these are at Wholesale Tools, they have 1/2" diam fully hardened HSS shaft, 8" long for $3.45. That's what I used for my skewchigouge, and my round skews, also.

See link below, the 1/2" x 8" long shaft is towards the bottom of the page.

The bar stock you mention most likely isn't hardened, and not easy to harden in the home shop.


Wholesale Tool: HSS round toolbits

Re: Beading tools ?

#18

Re: PDF of grind for skewchigouge on Woodcraft sit

Craig Daymon

>That is something I didn't realize would be necessary. It does say that the A11 steel will air harden to 65. I was looking at larger, longer stock. I was thinking about 5/8" and the stock listed was 36" (not that I was planning on a tool that long, but longer than 8" would provide).

Glaser has a tool, called a "Bowl Skew", that looks similar to a SkewChiGouge except with heavier stock. I'm thinking that a heavy stock SkewChiGouge ground tool might work pretty well and with little vibration being solid rather than fluted. (I'm thinking, but maybe not correctly. Still, I get some pretty good cuts from the standard SKG.

-Craig

Re: Beading tools ?

#19

Bob Moffett

Re: Beading tools ?

Bob Moffett

>Bill,

Thanks for the information. I am going to give that a try.

Bob M.