Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Sorby Spindlemaster

Posts

Sorby Spindlemaster

#1

Sorby Spindlemaster

Phil Axtell

>Hi all,

My bride gave me a 1" Sorby Spindlemaster for Christmas. I was just getting through the learning curve with it and accidentally touched it against my spinning chuck. Chipped a small piece out of the very center of the cutting edge. (The bottom of the flute if it had one.)

As the bevel is highly polished to make such a smooth cut, I don't know how to repair it. You are only supposed to sharpen the top edge with a diamond hone.

Anybody know what I can do now, except to try not to cut the chuck anymore? Or to get rid of it?

Thanks,

Phil Axtell

Re: Sorby Spindlemaster

#2

Sorby Spindlemaster

ob obrien In Pensacola

>Phil; I would suggest grinding the bevel at the same angle as before. Grind out past the nick. Then hone the bevel and the the flat edge on top. Maybe that will save it. Let me know if that works. OB

Re: Sorby Spindlemaster

#3

Re: Sorby Spindlemaster

Ed Moore

>Can a 1" tool fit in a Wolverine jig? I have three Spindlemakers (non-Sorby tools of the same type) and I resharpened one of the 1/2" tools that way. Then I worked the tool on some 1000 grit Wet-or-Dry paper from an auto supply store to reduce the hollow-grind, followed by some 1500 grit. Then I honed it on an MDF disk with some compound on it. Works great.

Ed

Note: I recommend Packard or Hamlet Spindlemakers over the Sorby models because they are thicker and the Sorby is thinner and "whippier". JMHO.

Re: Sorby Spindlemaster

#4

Re: Sorby Spindlemaster

georgetroy

>This tool is mostly for finishing cuts. I would put a safety groove in the base of the piece I'm turning to keep from running into the chuck. The groove is at the point where you would part it off anyway. All you got from the metal was your pride and a metal chip,for me it was a cut in my finger and stitches. Don't be afraid to resharpen it, you would have to some day anyway. GT

Re: Sorby Spindlemaster

#5

Re: Sorby Spindlemaster

Barry Irby

>I have a SpindleMaster on permanent "loan" from a friend who could not get the hang of it. I have not used it much, but I would say that unless you can reproduce that shape and polish, you are going to change the cutting characteristics of the tool. Of course, I really don't know, but I am assuming Sorby put that convex shape on it for a reason. Why don't you approach Sorby? They Might give you a break and sharpen it for you, if you promise not to turn any more chucks.

Re: Sorby Spindlemaster

#6

Re: Sorby Spindlemaster

adrien

>Basically the tool is a fluteless spindle gouge. So regrind the bevel and hone it until it's as before. Rude Osolnik came up with that idea about 30 years ago

Re: Sorby Spindlemaster

#7

I did the same thing and thought all was lost..

David

>but I reground the backside until the nick was gone and sanded it smooth as I could and used the tripoli wheel on it. Not exactly like the original, but at least it was polished and prertty smooth. Haven't used it much since, though, and its been too long to notice any change in performance.

Re: Sorby Spindlemaster

#8

Re: Sorby Spindlemaster

Ron in Drums PA

>For a lack of a better way of explaining it, I reshaped mine with a Ellsworth grind.

Re: Sorby Spindlemaster

#9

Richard Allen

Re: Sorby Spindlemaster

Richard Allen

>A rep from Sorby visited the local Woodcraft store a while back and I asked him about sharpening things like the "spindlemaster". He said that if the tool were nicked it should be sent back to Sorby. He indicated that the efectivness of the tool was dependent upon the bevel provided by Sorby.

There is one other posiblity. If the tool was purchased from WoodCraft then you should take it back to them for replacement. Woodcraft has a no questions asked 1 year warenty on everything they sell.

Re: Sorby Spindlemaster

#10

check with Nick Cook *LINK*

Bob Elliott

>Phil,

When the Sorby Spindlemasters where first introduced, Nick Cook demo'd them at the wood shows. I'll bet he could give you some direction re: repair / sharpening.

Nick Cook Woodturner

Artisian Resource Center

585 Cobb Parkway South, Suite I

Marietta GA 30060

Phone: 770-421-1212


img

nickcookwoodturner.com

Re: Sorby Spindlemaster

#11

Bogus...

Peter Teubel

>There not a turning tool available commercially that can't be sharpened with a little thought about the process. We had the Sorby rep at our club awhile back and he said the same thing. That's crap. Its nothing more than a flute-less gouge with a polished flat bevel.

All other turning tools come with a flat bevel, but that doesn't stop us from putting a hollow grind on it. I've sharpened those spindle masters on a regular grinder and there nothing to it. Just polish the bevel on a felt wheel after grinding the nick out.

You'll also be quite surprised at how much sharper it will be vs just the honing the top surface as Sorby recommends.

Re: Sorby Spindlemaster

#12

Re: Sorby Spindlemaster

Phil Axtell

>Thanks guys,

I really appreciate all your good advice. I will start trying to repair my Spindlemaster in the next few days. I contacted Robert Sorby and will wait to see what they have to say before trying anything.

I will post my results here as soon as I can.

This is certainly a great group when you need advice.

I will put this in a new thread for those who don't scroll down this far.

Thanks again,

Phil Axtell