Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

turners pains

Posts

turners pains

#1

turners pains

John Lucas

>Let's do a discussion on aches and pains that turners have and any solutions you have found. I'll start.

Carpel Tunnel. Use moderately large tool handles. A lot of us make our own tools and small diameter tools will cause Carpel Tunnel, especially small handheld hollowing tools like ornament hollowers.

Back problems In my old shop I had chinning bar. Just hanging from this several time a day really relaxes your back. Put a 4" block of wood near your lathe and put one foot up on it for a while. Alternate feet. This really helps your back.

Feet problems. I use a matt religiously. Good shoes are a must but I'm too lax on that one.

I won't even go into eyes, we all know safety glasses at the very least are essential.

Re: turners pains

#2

Re: turners pains

Mike Cunningham (Cape May)

>I too suffer from back problems. In the words of my neurosurgeon, my lower lumbar is a wreck. Heavy lifting, hard to avoid, and standing for long periods, even harder to avoid take a toll. I also use a block and alternate raising a foot, helps a lot. Sitting on the floor and stretching my lower back and hamstrings also helps.

For my feet I have custom designed inserts/arch supports that I obtained through my orthopod, these coupled with NB 609 cross training shoes or mid height leather work shoes are great.

At 6'4" and 285, it's no wonder my back and feet are letting me know they're not pleased. When I'm not turning or fishing I love to cook.........that's not necessarily a good thing.

Re: turners pains

#3

Re: turners pains

TDaniel

>John, long handles help a lot and you need to get rid of that lathe bed that makes you lean over all the time :). A bowl lathe or moving headstock really makes life easier. Take lots of breaks. Alternate work. I try to not spend a whole day roughing out; rough out a few bowls, then sand or apply finish on others, then hollow a little while, etc. Sanding all day is a bummer and will really tire the wrists, the pounding that your arms take when roughing out can really tire you out. Make certain your lathe is at the correct height so you aren't bent over all day.

TD

Re: turners pains

#4

JL

Re: turners pains

JL

>Shoulders - my big problem. I am trying to avoid rotator cuff surgery. Excerise and more excercise.

Gentle arm swing - bend over with one hand on a desk, table or bench. Leave the other arm dangling. Gently swing the dangling hand in circles about a foot in diameter - gentleness is the key word. Do it clockwise and counterclockwise 30-40 times.

Arm lifts - hold small weights (2-5 lbs) in your hands at your side. Slowly lift the arms straight out to the front. Three to four sets of 10. Also do this to the side.

Wall bounce - bounce a ball against a wall slightly over your head. Get a large "soft" ball (somewhat larger than a basketball). Do this about 50 times or so.

Slow and gentle for everything.

You can also do side pulls and a number of other excercises.

My $0.02.

Re: turners pains

#5

Dick Hines

Re: turners pains

Dick Hines

>I have a pain for you John. I have been using low handel bowl gouge style for a while and heveloped a pinched nerve in my right leg. It's not funny. I was working a a big bowl and it was very dry and hard. So I braced the bowl gouge in the joint between my leg and hip. After a couple of days of this I could hardley walk. Went to the Dr., told him my proublem and hes said I must have inflamed the nerve. I have been on drugs for 2 weeks. It's getting better, slowly. I don't hold the gouge on the hip joint anymore.

Re: turners pains

#7

Neck problems

Carole Valentine

>I have started having a few problems with my neck, especially when I wear my Trend or North. I think it has to do with the fact that when I am wearing either of those, I have to tilt my head down a little more to see over the air-wear. That and these darn bifocals.

Re: turners pains

#8

Re: Neck problems

Stuart Johnson

>"That and these darn bifocals."

Carole, You might consider getting a prescription for just the lathe (and my case the computer). You might find the doctor can write somehthing that is single vision good for one to say three feet.

Re: turners pains

#9

Re: Neck problems *LINK*

Fred Holder

>I was having neck problems in November. Several trips to the Chiropractor hadn't seemed to fix the problem, just moved it around a bit. I pulled out a dry elm bowl blank to turn. My wife said to core it so she could turn the smaller piece. I set it up to core with my Woodcut coring set up. The wood was so hard it just beat me to death as I fed the cutter into the wood. When I finished coring, I discovered my neck was fixed and the problem hasn't returned to date. I called this my Chiropractic Bowl. Maybe you just need to core a good hard piece of wood occasionally. It worked for me.


Fred Holder's Domain Site

Re: turners pains

#10

Re: Neck problems

John Lucas

>Carol I have bifocal's and Ihad the lower lens ground a little higher than normal. This keeps me from having to bend my head so much. It was more for the computer than turning but it does help when turning.

Re: turners pains

#11

Re: turners pains

Ron in Drums PA

>You folks sound like a bunch of old farts!

Although. I've noticed I'm making the same noises my father did when he would stand up from a chair.

I tell you what is bothering me, my hearing.

I think my hearing is going bad from wearing the Triton Helmet. Has anybody else notice this?

Re: turners pains

#12

Eeeh? What'd ya say Sonny??

Molly Winton

>

Re: turners pains

#13

Re: Glasses

Bill Hale

>Carol

Many of us wear reading glasses and find the computer is out of focus due to the screen distance. I have a pair of Rx glasses I use to read and a pair of drugstore glasses for wood working and the computer. Ask your eye doc or just go in to a drugstore and try some on. Test at arms length as if you were turning.

Cheap and throw away if you scratch. I have also found that I can clean the CA off with releasing agent and no damage to the lenses.

Bill in Casa Grande, AZ.

Re: turners pains

#14

Re: turners pains

George Fitzpatrick - Springfield MA

>Whoa!!! I was planning on getting a Triton tomorrow at a Wood Works show. Why would a Triton cause a problem with hearing?? I thought a benefit of this was the built-in noise protection....

Oh, and over 30 years of guitar playing, along with the computer stuff, and now turning, carpal tunnel is a definite problem.

Re: turners pains

#15

Re: turners pains

Mark Wollschlager

>I like my Triton. The noise maker is down at belt level, and the integrated ear muffs are always there to use. I find myself cranking the muffs out away from my head so I can hear the lathe better. Even without the muffs on it cuts the noise in the shop at bit. There is a small whine from the filter motor, but nothing to complain about.

Having the filter at the rear belt level has unintended consequences after dinner. I'll just leave it at that. ;-)

mark.

Re: turners pains

#16

Various ow-ies

David Breth

>Three things for me (so far)

1) North double cannister mask while light is a bit short for my giant nose, so I perpetually look like an old drunk (red nose). Solution - get the "large" instead of the medium north 7700. One of these days.

2) A little lower back fatique after about an hour and a half - this started after I added ear muffs to my arsenal of headgear, so I guess I better get a lighter solution, which isn't exactly rocket science to take care of.

3) Hand cramps. I don't power sand anything. If I can sand on the lathe, not that big a deal unless the piece is real small, but if I have to (wet) sand anything off the lathe, I just capitulate that my hands will be crampy and exhausted soon. I've got to watch that, because I've had difficulties in the past with repetitive motion pains in the hand.

David B.

Re: turners pains

#17

Re: Various ow-ies

David Breth

>Oh - and burning-hands from effective bowl gouge use. Good news/bad news - I get good passes, but the shavings are melting my hand. For the first time a couple of weeks ago, I used a golfing glove because it was so bad on one bowl I just couldn't take it anymore. Haven't worn it since though - don't mean to rekindle that debate....

Re: turners pains

#18

Re: turners pains

Ron in Drums PA

>The only time I have problems with my hearing is when I wear the ear muffs. wink wink nod nod

I love my triton, I would buy it again.

Re: turners pains

#19

Stiff legs

Jorge Castaneda

>Last time I had a sitting job was 1961, since all my jobs have been standing, that and advance old age makes my legs very stiff when standing un one spot, not bad at all if I am moving, also stiff index and heart fingers on right hand, but I think the mouse is the culprit, altho I did pound in millions of nails too.

Jorge

Re: turners pains

#20

Dick Hines

Re: Neck problems

Dick Hines

>Carole you need one of those straps like the NASCAR guys have that keeps their heard from flying off in the corners.

Re: turners pains

#21

Never really had any problems..

Peter Teubel

>...when turning when I was turning full time. I was sore at the end of the day, to be sure. But it was a nice "I've-been-working" soreness that made me feel like I've accomplished something during the day. Now that I've been back in the high-tech world for 18 months(i.e. sitting on my @$$ in front of a computer), I'm a mess. First, my wrist and shoulder got messed up from the mouse. After trying all kinds of wrist supports and rests, I switched to a thumb trackball. Now my thumb is causing problems (its painful to grasp things very hard now). Next device to try is a finger operated trackball. If that doesn't help, I'm going back to DOS! And I won't even mention my syatic issues.

Working with computers professionally is definitly profitable, but NOT healthy...

FWIW, my turning comfort was enhanced by a nice thick foam rubber floor mat, comfortable shoes (changed them every few hours), big heavy handles on my tools, and a relaxed grip. When power sanding, I would use gel-gloves to deaden the vibration to my hands.

Re: turners pains

#22

Re: Various ow-ies

John Lucas

>David Get one of the Sanding gloves from Bruce Hoover. They have velcro on the glove so the sandpaper sticks to it. You don't have to grip the paper so your hands don't cramp. I cut a tendon in my left hand and it will start cramping sometimes when sanding. The glove stopped that.

Re: turners pains

#23

Keith Tompkins

Re: turners pains

Keith Tompkins

>Lyme disease....misdiagnosed for several years...everything hurts, sometimes different joints as the pains seem to move around at will. I cannot use a hand held weedwacker, I cannot lift my arms afterward...my joints are very painful. My neck is a big problem, as are my knees. Could be worse, I suppose.

Re: turners pains

#24

Re: Nail Problems

Charlie Anderson

>I never lost a nail in the first 64 years. Then I took up turning.

Carrying a log, I bumped into another log with my finger in between. Result: lost nail

Dave Smith solf me 2 bigleaf maple blocks, each 6 pounds. I unpacked them and was showing one to my wife. Lost my grip and it fell point first on my big toe. It left a nice little right angle dent in my shoe.

Result: Nail coming off any day now!

Re: turners pains

#25

the computer generation

JKJ

>>...First, my wrist and shoulder got messed up from the mouse.

It's a never ending battle. Fingers on both of my hands started going numb after about 15 years of hard-core software developing, so I switched to computer graphics. I then proceeded to ruin my "mouse" shoulder which required surgery and never has properly healed, and my "mouse" hand/wrist has sharply worsened over the last few years. It is beginning to limit the hours I can work at the computer, and interfere with my piano playing! I feel FAR better after a few days away from the computer, whether turning or tractoring (or sawmilling :).

We are seeing far more of these computer problems as the first computer generation ages. The next generation my be in crisis since many started much earlier in life. People, while you can, run away from the computer, run away!!

BTW, one thing that seems to help with the mousing - get a tablet and alternate between it and the mouse to give some of those muscles and nerves a rest.

I'm convinced that after 30+ years of computer work, the only solution for me is retirement! (90 work days and counting)

JKJ