Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

The hardest cut in wood turning:

Posts

Re: The hardest cut in wood turning:

#26

Keith Tompkins

Re: The hardest cut in wood turning:

Keith Tompkins

>I have tried a hatchet...works pretty well, but I'd hate to get a catch :0/

Re: The hardest cut in wood turning:

#27

Re: The hardest cut in wood turning: Like Molly

Phil Joines

>Get a 3/8" 2 flute round end mill (MSC # 01761246). Mount it in a long piece of 5/8" or 3/4" round stock with a handle. With a little practice it will make those cuts fairly easy.

Re: The hardest cut in wood turning:

#28

Re: The hardest cut in wood turning:

Ken Grunke from SW WI

>John, starting a cove is also a hard one for me. Do you find it easier to start the cut with the long point of the skew?

Especially when a cove is a full half circle, I would start with an oversize diameter, then trim it down after the cove is finished--I mean, finish the cove first before turning whatever profile from it's edges.

Re: The hardest cut in wood turning:

#29

Re: The hardest cut in wood turning:

Ken Grunke from SW WI

>Keith, do you mean with the skew on edge, long point down, and swinging the handle around to cut the bead from it's peak down to the V on either side?

I seem to have better luck using a skewchigouge ground from a round shaft, and just twirling it each way. I have to get my nose right into the work for the small ones.

Re: The hardest cut in wood turning:

#30

My feelings exactly!

Eddie Pacheco; San Jose, Ca.

>

Re: The hardest cut in wood turning:

#31

Re: The hardest cut in wood turning:

John Lucas

>Ken I teach my students 2 things. Make a shallow cut with the parting tool to establish a shoulder for the bevel of the gouge to start on. Use the toe of the skew as you said to create a shoulder similar to the parting tool cut, this is cleaner of course.

Re: The hardest cut in wood turning:

#32

Thank you for making these videos, Ken!

Eddie Pacheco; San Jose, Ca.

>

Re: The hardest cut in wood turning:

#33

Re: The hardest cut in wood turning:

RussFairfield

>is the one that I can't make when there are 20 people watching.

Re: The hardest cut in wood turning:

#34

Re: Hey Ken *LINK*

Ken Grunke from SW WI

>Ron, the curved edge absolutely made a difference. I was making really good spirals with a straight edge skew, and after putting the slight curve on the short point side, I was rolling beads with reckless abandon most of the time without spirals. If you know how easy it is to use a spindle gouge to make a convex cut around to center, it's because of it's curved edge. Even a slight curve on the skew helps.

Below is an article by Alan Lacer, on his website which makes for good reading:


My Friend the Skew by Alan Lacer

Re: The hardest cut in wood turning:

#35

Re: I can help with this one...

Tom in Red Deer

>Terry, I'd say you have been looking at my tools. I have an older style bowl gouge that is very skinny and pointed. It works wonderful on the sides but not on the bottom. I will fix that.

John, you are also right. I usually make a fairly tight radius between wall and bottom. I will fix this as well.

I will look in the grinds section but I bet the tool I have can't be ground as you suggest .. it is too skinny. I will get the proper one.

Thanks for your help, it will likely save on the laundry!

Tom

Re: The hardest cut in wood turning:

#36

Re: I can help with this one...

Tom in Red Deer

>Here is the offending tool. The flute is actually 3/8 in wide. It is a Crown tool that was given to me. I had a look at the grind you mentioned ... is this tool a candidate for that?

It is still ground the way I recieved it and it does a wonderful job on the sides, just not the bottom or transition.

Tom


img

Re: The hardest cut in wood turning:

#37

another view 

Tom in Red Deer

>


img

Re: The hardest cut in wood turning:

#38

gouge is good

T Daniel

>it is just sharpened too steep, both the nose angle and the side angles are too steep. Compare to the grinds shown by Ellis, Dave Peebles, and myself. You need a rounded end and a convex side (top), and about a 65 degree angle for the nose and side. This is a very common problem and I see it often. I plan to cover this at our "Gathering" in April.

TD

Re: The hardest cut in wood turning:

#39

Re: gouge is good

Tom In Red Deer

>Thanks TD

I will make an attempt to grind it as per the pics and your instructions. It is a nice long gouge and well balanced and it would be nice to use it more.

Tom

PS: Would that be considered a dangerous weapon when crossing the border these days?

Re: The hardest cut in wood turning:

#40

They took my pocket screwdriver.

T Daniel

>

Re: The hardest cut in wood turning:

#41

Keith Tompkins

Re: The hardest cut in wood turning:

Keith Tompkins

>Yes, not laying flat...

Re: The hardest cut in wood turning:

#42

Re: They took my pocket screwdriver.

Tom in Red Deer

>I best leave it at home then!!!

Tom

Re: The hardest cut in wood turning:

#43

Re: The hardest cut in wood turning:

MFoster

>I have to agree with Barry. I agonize over just exactly how I want to make that first chainsaw cut. It seems to me that the first cut with a chainsaw determines what you live with. The problem for me is compounded when I have a big beautiful burl staring at me. I often delay cutting into a log or burl because I just dont feel right about it. Silly, because I end up cutting it up at some point and usually rely as much on luck as I do about my knowlege of wood (or burl) structure.

Re: The hardest cut in wood turning:

#44

Re: The hardest cut in wood turning:

Doug Trembath

>Watch David Ellsworth's video on the five cuts with a bowl gouge. He shows you a couple of cuts that will ease the transition for you. I don't subscribe to everything David teaches, but he is an acknowledged pioneer and master. Seeing it done is worth a thousand word article, IMHO.

Doug Trembath

Studio in the Woods