Re: VERY simple tip (finding center)
Dick Hines
>Why not just get one of those zero zero center finders. They are only $8.50 at Wood Craft. If the lines do not cross at the center just use a steel ruler to extend them. Works for me.
Knowledge You Can Build On — Est. 1998
Re: VERY simple tip (finding center)
Dick Hines
>Why not just get one of those zero zero center finders. They are only $8.50 at Wood Craft. If the lines do not cross at the center just use a steel ruler to extend them. Works for me.
Re: VERY simple tip (finding center)
Ken Grunke from SW WI
>I had to think about this idea a bit, at first it seemed like the process of drawing the most accurate square you can was a lot of trouble. Then I came back to it later in the day, and a light went on in my head. A rafter's square, or any flat square suitably sized for the piece is used, by placing the corner anywhere on the edge of the circle--then two lines are drawn, the square is flipped 180 degrees or a close approximation thereof, to draw the other two lines and the diagonals are drawn.
If, instead of an L-shaped square you had a square template whose side dimensions are at least as big as the circle diameter, just make the first two lines then slide the template diagonally until the other corner meets the opposite edge to mark the other two lines. The square needs to be big enough to mark the diagonals, so you don't have to reach for another straightedge.
I've used the tape measure method mostly, but like the square idea since it eliminates the headwork of having to divide an odd measurement by 2. Sure, you can fudge the position of the tape to go between 1/2" marks to make it easier, but that can get a bit clumsy if your shop is cold and you're wearing gloves, shivering, and you don't even want to take off your gloves to get the tape measure out of your pocket. Thanks Mike.
Re: I've used a square, but don't draw a square.
Al Crandall (NE of Indy)
>Mike's method is really simple and I've used it before. I use a square (anything with a 90 deg corner will suffice) but I don't draw the square. What you eventually want to construct are the diagonals crossing at the center. You don't need to actually draw the square. Just put two tic marks on the periphery of the circle where the legs cross the circle. If you join these marks you have drawn the diagonal of a rectangle which is also the diameter of the circle. By rotating the tool with the 90 degree corner somewhere near 1/4 turn and repeating the process you have drawn an intersecting diameter. You can find the center of a dime using a business card, or the center of a turning blank using a framing square. Just put the corner of the tool on the circle and go.
Re: VERY simple tip (finding center)
Keith Tompkins
>Boy , I hope this post doesn't offend anyone....Like Jamie, I just eyeball it...unless it's a spindle turning requiring great accuracy. I pop a blank between centers, and find the best balance point. When the blank doesn't swing down much in any direction, it' s fairly well balanced. Then I turn it down and adjust for grain orientation, defects, etc.
Re: Get the "most" or the "best"?
JKJ in East TN
>>...scrape away parts of the circle lines to
>yeild a solid line with the next circle
>being a dashed line ...
What a great idea. I used one of those templates once and it made me dizzy trying to follow around the ring with my eyes. I think I'll make one myself with different colored rings using some Sharpies. Long live the Sharpie.
JKJ
Question for Mike....
Ron Meadows
>Do you start drawing the square by just eyeballing the first line then making all the subsequent lines by keeping the formed angles 90 degrees? I'm having trouble seeing how you actually perform this proceedure.
Thanks,
Ron
Re: I've used a square, but don't draw a square.
adrien
>Hey Al,
Like Ron, I wondered how one would draw the square. Your method seems simple and effective (lately the word "efficacious" has come into vogue) for the geometrically challenged (me).
Re: I've used a square, but don't draw a square.
Don Henthorn
>That is the way I have always done it. Hey!, There are so many good ways to do it presented here I would waste an hour trying to decide which one to use.(G)
Re: Question for Mike....
Mike Schwing from Md.
>Ron, I have a few sets of identical squares. I simply find one that fits inside the circle and line up a corner with the rim. Then I swivel it around till the other two touch edges as well. Take the other square, invert it, and form the square. Works well for me and only takes a few seconds. Doesn't have to be perfect, but I don't prefer to spend my time truing up blanks on the lathe.
Another Way
gtwilkins
>Trace around the blank on paper, cut out the circle and fold in half twice to find center.
This reminds me of the old "how do tell the height of a building with a barometer" question!
Cold as all heck here in Grand Forks but sunny, Trevor
OH! Thats really cool!
Mike Schwing from Md.
>I would have NEVER thought about that!
Re: Question for Mike....
Ron Meadows
>Thanks Mike. I get it now...you use 2 squares. I was trying to figure out how you managed to do it with only one.
Ron