Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Gluing bristles into a handle *LINK*

Posts

Gluing bristles into a handle *LINK*

#1

Gluing bristles into a handle *LINK*

Basil Biberdorf

>I'm an Orthodox priest in need of a new blessing brush (similar to the one in the link below).

I turned a handle last night, from a burl cut-off that was too small for anything else. It came out nicely. The question now is, what's the best method for gluing the bristles, which are essentially broomstraws, into the handle? Both hot glue and wood glue (Titebond, etc.) have come to mind. Any other ideas or thoughts on this? Note that the brush will be in contact with water (at least on the bristles) any time it's used.


http://www.stspress.com/detail.aspx?ID=1254

Re: Gluing bristles into a handle *LINK*

#2

Jim DeLaney, Austintown, Ohio

Re: Gluing bristles into a handle

Jim DeLaney, Austintown, Ohio

>I think I'd drill the end of the handle - maybe 3/4" deep - and the same diameter as the bundle of bristles, so that the bristles are inset into the handle.

For glue, I'd use epoxy. Something like System Three T-88, or the equivalent. You could probably get by with any brand of 5-minute epoxy, though.

Jim D.

Re: Gluing bristles into a handle *LINK*

#3

Re: Gluing bristles into a handle

Basil Biberdorf

>The handle is drilled about halfway through the length of it to give the bristles a good anchor. Thanks for the epoxy idea. Any others from anyone?

Re: Gluing bristles into a handle *LINK*

#4

Re: Gluing bristles into a handle

Rick Allen

>The shaveing brush heads I buy are glued in with epoxy when I buy them. No doubt if there was a cheaper way to do it that was as effective at holding the bristles for that application they would be using it.

I would use a small cup to glue the bristles into. Then glue the small cup into the handle. That way I wouldn't mess up the handle trying to glue in the bristles.

Good Luck

Re: Gluing bristles into a handle *LINK*

#5

Re: Gluing bristles into a handle

Lan Brady

>Basil,

If you use Titebond, be sure it is Titebond III. THat is the waterproof version.

Actually, I cannot imagine being able to hold the bundle tight enough to keep the individual fibers from falling out. Lots of luck and please post the picture when you are through.

Lan

Re: Gluing bristles into a handle *LINK*

#6

Re: Gluing bristles into a handle

Ken Grunke from SW WI

>I'd try polyurethane glue (gorilla glue, for one).

Gob a little in the hole, then insert the bristles--pushing the glue down to the hole's bottom, where it will expand/foam up and not make a mess on the outside end of the hole. This expansion/foaming up may push the bristles out, unless you secure them somehow--duct tape?

Anytime I have a question on glue, I look at Russ's Corner, under "Other Articles" in the left menu.

Re: Gluing bristles into a handle *LINK*

#7

Re: Gluing bristles into a handle

William Duffield, on the Cohansey

>Here's a mahogany and horse hair bench brush I made:


The recess is less than an inch deep. Mine is not expected to get wet, so Titebond worked fine. The bundle is tied tightly with string, which held it in place while the glue set. You can see where the glue wicked onto the surface and discolored it slightly, so be careful not to use too much glue. There was no need for duct tape. I just put the handle in a vise with the bristles up while the glue dried. This method would work even better with epoxy.

My first choice would be epoxy. Second choice would be Titebond II or III. I would not use hide glue for your application, because it the water would loosen it. I would also never use Gorilla Glue, even though it is waterproof, because it would foam out all over the place while it was curing, and you'd never get it off the bristles. Epoxy is better than Titebond, because you can replace the bristles if they get worn in the future by heating the joint with a heat gun. That won't work with Titebond or any other aliphatic resin glues.

Re: Gluing bristles into a handle *LINK*

#8

Re: Gluing bristles into a handle *LINK*

adrien

>http://www.woodturnerscatalog.com/cgi-bin/shopper?preadd=action&key=131-0175

at Craft Supplies might interest you

they call them "dusters," but perhaps this is close...


duster brush�Craft Supplies

Re: Gluing bristles into a handle *LINK*

#9

Re: Gluing bristles into a handle

William Duffield, on the Cohansey

>Whew! That's a lot better price than my $400 per lb. horsehair.

Seriously, the horse hair was offcuts from very special Chinese white horse hair for violin bows. Like lots of offcuts in many specialty industries, what is one man's trash can often be another man's treasure, but you have to look hard for it, it is often available only in very limited quantities, and you have to be inventive.

Re: Gluing bristles into a handle *LINK*

#10

Re: Gluing bristles into a handle

Mike from St. Clair Shores

>I liked the epoxy idea, but I've used clear silicon. It takes longer to dry but is water resistant and a great bonding agent for bristles, rope, hair etc.

Mike

Re: Gluing bristles into a handle *LINK*

#11

Re: Gluing bristles into a handle

Basil Biberdorf

>Thanks for all the replies. I'll give epoxy a try, since it seems to be the least expensive and most available solution (meaning I don't have to pay big shipping charges for a small order).

The duster brush from Craft Supplies is an interesting item, but the brush end is larger (fatter) than is typically used. I need some throwing control here. :)

Re: Gluing bristles into a handle *LINK*

#12

Re: Gluing bristles into a handle

tek-Brunswick, Ohio

>Craft Supplies also ahs basting brush inserts. Those may be closer to what you are looking for.