We value your privacy.
We use cookies to enhance your browsing experience, analyse site traffic, and personalise content.
By clicking “Accept all”, you consent to our use of cookies. You can also choose
“Essential only” or learn more.
It's usually called a log jack, similar to a cant hook but with a jack extension. I bought one a few months ago and it works great, especially when bucking logs and limbs in the woods. It's harder to use with small pieces since it needs one end on the ground for stability (unless I'm using it wrong.) Lots of places carry these, even Highland Hardware.
BTW. a peavey looks like a cant hook but has a steel point or spike on the end instead of a flat end with a hog nose to grip the log. I understand these were used primarily for working with floating logs and log jams.
I bought a 5' cant hook last week to use with my sawmill. I had already been impressed by my 4' cant hook but it's amazing how large a log one person can grasp and turn with the 5' version. Those, a 6' steel pry bar, and a couple of 25" skidding tongs for the tractor and I'm in business. I cut and hauled in about 4 tons of white oak today so I'll get some practice with these toys this weekend. (This was from one tree and I had to leave most of it - the main trunk was about 4' in diameter, too big for me!)
>I've got two white oak trees that size that are dying. I'm hoping I can whittle them up enough with my 16" and 18" chainsaws to get some stuff worth turning!
>Jennifer, my sawbuck is similar to Steve�s; I have a sacrificial bottom and end board for smaller pieces and cut my blanks round while resting on top of the two full size 2x6. Using the end board keeps pieces in place while ripping without clamping in place. The base is screwed together but there is no metal accessible to the chain while cutting. The sides are easily replaced when they get cut too much to hold anything.I do cheat and place the larger blanks on the sawbuck with the Bobcat or tractor!
>Here's a photo from that Minnesota Woodturners Association newsletter article for those who just want to see its basic design. This was inspired by a photo posted here of one built by Dave Peebles. I believe I posted this photo once before.
That's my turning buddy Steve Tiedman at the sawbuck. We built two of these from a variety of new and old pressure treated lumber and recovered fence posts. We store our outdoors.
>If you are working at your house or yard, you can get a used engine hoist to lift the huge pieces onto a stand of some kind. This allows you to get bigger pieces higher so you don't have to bend over. I see lots of cheaper engine hoists for sale in the local for sale sheets. MP Wall
Should have added a hinged plywood step-on to keep it from racking but it works prety good in the bush. I fold up to take less room and makes it easier to carry.
>While the engine hoist and bobcat lift approach is probably the best I take a more low-tech approach to getting the rounds up on the buck.
I use the same ramp that I used to put it in the back of the truck.Mine are made with those aluminum ends that used to be called Ramp-parts and attach to either end of simple 2X lumber.
If you plan ahead(my friend does,I never quite make it)you can make the buck the same height as your truck`s tailgate and even eliminate the ramp.
The real question is why do I always think of this stuff or find out about it AFTER I have a mountain of choice turning stock setting on carefully placed sleepers so as to raise the logs/burls exactly 6" off the ground?
I told you I wasn`t any good at planning ahead.Now where did I put that ramp...
>I use a big chunk of maple with a slight v cut on top. It is 2' by about 3'diameter that I picked up at the dump using a Harbor Freight reciever hoist on the pickup. I use a cant hook to roll logs onto the hoist then lift and rool into the truck. I have the big chunk in the driveway and back up to it and roll the log off on the chunk and proceed to making several more bushels of chainsaw mulch.
>>I've got two white oak trees that size that are dying.
>I'm hoping I can whittle them up enough with my 16"
>and 18" chainsaws to get some stuff worth turning!
Brian,
Fortunately, I just got a new Stihl with a 25" bar or I would have been unable to slice up the main trunk. (The tree was already on the ground.)
If you need to fell a tree larger than your bar, you may be interested in a method I first read about in the book "The Good Woodcutter's Guide" (by Dave Johnson, excellent book, BTW). It involves making a plunge cut from the front after the wedge is removed, then removing the back. That said, trees that big scare me and I personally would leave the felling to the experts! (And yikes, when cutting any dying tree, keep a sharp lookout for dead "widow maker" limbs. These are especially hard to spot in the winter when the leaves are gone. A neighboring farmer went to the emergency room for 17 stitches in his head from one of these - and he was lucky. I always wear a helmet but even that wouldn't help with a large limb.)
For even more excitement: If the tree is on the ground but still too big to cut up, I read in another forum about a time-honored method to split a large trunk (link below): make a deep longitudinal plunge cut near one end of the tree. Fill the hole with black powder and ignite (a battery with hot wire is a lot safer than a fuse). This will reportedly split even the largest tree as long as it's not a species with interlocking grain. Of course, close neighbors might object.
As for the white oak I cut yesterday, I managed to carve out some highly figured chunks for a turner in the tree owner's family, some of them nicely spalted. The longer bar on the saw helped a great deal with this as well. While the pumpkin pie was cooking today I unload what I carried home on my truck and trailer and got one 26" log on the sawmill. Gonna have some fun tomorrow!
I don't know your definition of what is "worth turning", but if you want white oak and can't get some from your trees, let me know and maybe I can fit a chunk into one of those flat rate boxes for you. I didn't specifically save any figured pieces, but I plan to saw large beams and may well have some offcuts big enough for bowls.
I've got a neighbor that spent 10 years as a logger. He's been gathering dead wood from my place for firewood and also deer hunts my woods (got a real nice on on opening day last weekend). On the other hand, those trees are at the edge of a ridge-top field and maybe a really strong gust will take them out one of these years. Probably over the edge of the ridge into multi-floral rose filled drop-off! Meanwhile I've got one that blew down in the far northeast corner of my woods (1/4 mile from house) that I can play with. With a little patience and persistence, I can get nice big pieces even with a 16" bar. (Practised on two maple trees a number of years ago, one was almost solid burl, the other was completely quilted.)
That method for splitting looks interesting and is very feasible where I live. Thanks!