Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Hey Ruth Niles!

Posts

Hey Ruth Niles!

#1

Dave Shombert

Hey Ruth Niles!

Dave Shombert

>Hi Ruth,

If you recall, I bought the Oneway grinding wheel balancing setup at the Ohio Symposium and I said I'd let you know if it works.

It works. I was a little skeptical of this thing, but I can definitely see/feel a difference. I'm using Oneway's wheels on a Baldor grinder and they weren't THAT much out of balance. A little bit, though, and the balancing smoothed it out.

Just thought I'd let you know (and anyone else who's interested). Hope you're well.

Dave

Re: Hey Ruth Niles!

#2

Same Results, Excellent!

Jim Shaver - Oakville, Ontario

>Hi Dave,

I have installed two sets of these same balancers on two grinders, they have made the world of difference in both cases....highly recommended.

Take care,

Jim

Re: Hey Ruth Niles!

#3

Re: Same Results, Excellent!

Mike from St. Clair Shores

>I also have two grinders. They both used to make things rattle and fall off of a large work bench (4'x7') I put the OneWay balancing system on one of the grinders and the difference between them is phenomenal. I hadn't used the one without the system for several weeks and I forgot how bad it vibrated. I went to it to do some rough grinding on some HSS that I was making into a tool, and within minutes anything not screwed down was making its way to the floor, including a can of shellac that blew its top when it landed. I am saving up and watching for sales to get another set.

Mike

Re: Hey Ruth Niles!

#4

Re: Hey Ruth Niles!

Ruth Niles

>Hi Dave,

I'm fine, thank you for asking.

Ok, on your recommendation I'm ordering that wheel balancing set up from Oneway. One wheel on my grinder must be out of balance because it will not dress up no matter how I try while the other wheel runs perfect. I hate when wheel won't dress, there's nothing worse than a naked grinding wheel! : )

Ruth

Re: Hey Ruth Niles!

#5

Re: Same Results, Excellent! LOL!

Ruth Niles

>Mike, sounds like that grinder is costing you more money and time rattling things off the table and a whole can of finish spilling. Maybe you'd better not wait?! : )

Ruth

Re: Hey Ruth Niles!

#6

Re: Hey Ruth Niles!

Sean Troy

>One other thing that may help is a single wrap of masking tape around the arbor. Sometimes the difference in dia. of the arbor and wheel spacer ID are slightly off.

Re: Hey Ruth Niles!

#7

Re: Hey Ruth Niles! - Slight Hijack

Mark Kauder, Phenix City, AL

>Hi Dave,

Good to see (read) you around here.

Grinding wheels - Back at the Southern States Symposium, Stuart Batty recommended the Norton SG wheels for sharpening - especially the high end metals in the Glaser tools.

BUT they are almost $100 each. I have been using some soft white Norton wheels that Lee Valley was selling. They did well, but wear down really quickly.

SO....in a fit of "oh, what the hell, it's only money" I bought one of the SG wheels. IT IS FANTASTIC!!! Not too hard, does not load up, does not wear too quickly. I am positive that they are well worth price difference.

Mark

Re: Hey Ruth Niles!

#8

Just for the heck of it

Frank G ( Ingleside Texas )

>Try loosening the unbalanced wheel and turning it 1/8th to 1/4 turn then try it. You may want to mark your wheel so you can keep track. When and if you find the sweet spot then true your wheel. If you have an insert in your wheel that could be a problem too.

Usual disclaimer.

I don't know nothin.

It got below 80 degree's today and had to find my coat.

Re: Hey Ruth Niles!

#9

Re: Hey Ruth Niles! - Slight Hijack

-e-

>i switched to the oneway grinding wheels and REALLY like them. last much longer and produce a quality edge.

http://www.oneway.on.ca/sharpening/wheels.htm

Re: Hey Ruth Niles!

#10

Dave Shombert

Re: Hey Ruth Niles! - Slight Hijack

Dave Shombert

>Hi Mark,

Thanks for the input. I've heard others say the same thing but the price has deterred me. Now maybe you've pushed me over the edge. Ha ha, get it, "edge", ha ha. What grit Norton wheel did you get, and do use that for all tools - gouges and scrapers?

Dave

Re: Hey Ruth Niles!

#11

Re: Hey Ruth Niles! - Slight Hijack *LINK*

Mark Kauder, Phenix City, AL

>I bought the 8" 80 grit. The SG wheels are only offered in 46 and 80 grits, but I already prefer the 80 grit for most everything. I have a decent 120 grit white wheel that I use when I want a fine burr on a scrapper, and I also use it when I hand grind a gouge (like with Stuart Batty's 30 degree grind) because that is the place where I have the regular tool rest rather than my Vari-grind.

Mark


http://www.woodturnerscatalog.com/cgi-bin/shopper?preadd=action&key=234-8080