Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

vacuum pump

Posts

vacuum pump

#1

vacuum pump

John Lucas

>I'm getting ready to redue all the wiring and hose to my vacuum pump. I have several questions. I used the clear vinyl tubing the first time. It worked fine for a year or so but is now starting to collapse when in use. I though I would look for some vacuum hose from the automotive store. Is that what you all use.

My second question is where do you store yours. My lathe sits out in the middle of the garage more or less so I can't really put it on the wall without running long vacuum hoses and long wires for the switch. I have a short bed extension for my Powermatic which I put on the headstock end and thought that I might mount it below that on some sort of platform. I also use it on my mini lathe occasionally so i though about making a mobile base for it to sit on. It would sit below this extension. I could build a small rolling cabinet and store my vacuum chucks in there as well as holding the motor. In fact I could put a fan and filters in the cabinet to keep the motor cool and clean.

OK now that I've thought this through and answered my own questions I'm still interested in what you all do.

Re: vacuum pump

#2

Re: vacuum pump

John Uteck - Charlotte, NC

>John -- I use the hard poly tubing available from Home Depot/Lowes/local hardware store -- not soft vinyl tubing. It's fairly inexpensive when you buy by the foot for what you need. I think mine is 3/8".

I keep my vac pump permenently mounted on a shelf below my lathe (Jet 1642 - non-mustard color version of yours). For a mobile unit, contact John Hill (Carolina Mountain Woodturners / AAW board) -- he had a small setup on a platform on casters that he brings around to demonstrations - he may have a photo of his setup.

Re: vacuum pump

#3

Re: vacuum pump

Keith Bundy

>John, if your lathes sit close enough together you could mount the pump in the ceiling and use enough hose to reach both lathes.

Re: vacuum pump

#4

Here's mine

CapeMayMike

>Mine is mounted outboard and just beneath the headstock. It hasn't been there that long so I can't comment on possible problems. It sure is convenient. I built a small plywood platform with legs and tied the platform to the lathe frame. My vac pump is a Gast 220 from Surplus, I added a transformer and wired that into a switch and also have a receptacle where I can plug in accessories. Same tubing as you've been using with quicks. I have a length of standard air hose with quicks which I intend to use with the pump for a vacuum press.


img

Re: vacuum pump

#5

Another view 

CapeMayMike

>


img

Re: vacuum pump

#6

Oops

CapeMayMike

>Here's the other view


img

Re: vacuum pump

#7

Re: vacuum pump

John Lucas

>Cool Thanks guys. That's more or less what I have in mind.

Re: vacuum pump

#8

Re: vacuum pump

John, Ohio

>John,

I put mine in a cabinet and put some styrofoam around it to muffle the sound. Real glad I did as it is pretty noisy.

Good luck.

John

Re: vacuum pump

#9

I use Lowe's 1/2" milky white tube. No collapse.

Al Crandall- NE of Indy

>

Re: vacuum pump

#10

Re: I use Lowe's 1/2" milky white tube. No collaps

Jim Ketron

>I got mine from Home Depot clear with the reinforced mesh in it

Here is my set up I keep Mine on the wall ant the end where I do My finishing work.


img

Re: vacuum pump

#11

a close up 

Jim Ketron

>


img

Re: vacuum pump

#12

Re: Here's mine

Mike from St. Clair Shores

>This question is for CapeMayMike. What does the transformer do that you mentioned in your post? I think I see it in the front of the picture. I also have the Surplus Center 220 Gast. I have been wanting to build the setup that is on the Joe Woodworker site with the 4inch PVC.

Re: vacuum pump

#13

Re: I use Lowe's 1/2" milky white tube. No collaps

John Lucas

>Cool set up Jim. You may be the only person I know who still has the Powermatic cage in place. I hadn't though of mounting the compressor in a vertical position. No reason not to. When I design my cabinet I'll take that into consideration.

Re: vacuum pump

#14

Re: Here's mine

CapeMayMike

>It converts the 220 pump to 110. I have 220 in the shop but didn't want to run the pump on the same circuit as the lathe, though I'm guessing it would been okay.

The transformer is also available through Surplus Supply.

Re: vacuum pump

#15

Compressed air hose

Dominic Greco in Richboro PA

>John,

When I first built my vacuum chucking system, I used the clear hose as well. But I later changed that out for some compressed air hose and some quick disconnect fittings. It makes setting up the vacuum chuck and tearing it down a snap.

Since my background is pneumatic conveying (dust collection) I was sure that the long length of compressed air hose (about 10ft) would result in a loss of vacuum. However, this is not the case. It works perfectly.

See ya around,

Dominic


img

Re: vacuum pump

#16

Re: Compressed air hose 

Dominic Greco in Richboro PA

>


img

Re: vacuum pump

#17

Be careful with vertical mount

Bill Turpin in WNC mountains

>Bearings that are designed to be operated horizontally do not usually have the capabilities to run in a vertical manner. It takes about twice the internal guts in the bearings to stand up to radial and vertical forces, as opposed to mainly only radial. A good test of this is to use a long screw driver as a stethoscope. Place the pointy end on the end bell of motor and the handle against your ear. Then compare the sound horiz. and vertical. Any difference in pitch of sound or volume would show you that vertical is not the way to go. This is also a good test to locate which bearing of a multiple bearing device is defective. All the background noise is filtered out. Good luck.

Bill in WNC mountains

Re: vacuum pump

#18

Re: vacuum pump

jwoodwright

>The Compressed Air Hose is a great idea Dom, as it acts like a vacuum resevoir. Actually longer hoses may give you the opportunity to "Seek Cover" if the power suddenly went off. (Due to the reserve vacuum...) Perhaps a vacuum chamber added to reduce the risk of suddenly losing power...

Re: vacuum pump

#19

Duh... Of Course

Brian Hahn in SW Wisconsin

>Back when I was in college (late 60' & early 70's) we used thick wall rubber tubing for our vacuum hose. (And that was for diffusion pump vacuum systems!) Air line hose has the same qualities and is readily available at the consumer level. Just as long as the fittings don't leak, or at least don't leak enough to matter.

Great solution!

Re: vacuum pump

#20

Vacuum Pump Cabinet

David Propst

>Hi John,

Here is a photo of my vacuum pum set-up. It is based on a similar set-up on David Peebles website. The cabinet is an unfinished one from Lowes. As you can see it sits right next to my lathe and has castors.

The pump is mounted to a board and sits in the bottom and easily is pulled out if needed. A deep drawer was added for my vacumn chuck parts. The cabinet is wired to switch on the pump from the outside and includes an outlet that is used mostly for sanders.

It is fairly quiet. I thought of adding insulation, but it has not necessary.

I cleaned the shop last week before Gary Evans came to visit, otherwise the top would be piled high with toolrests, chucks, etc.

Best Regards,

David


img