Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

videos

Posts

videos

#1

videos

Pat

>Can someone reccomend a beginers bowl turning video?

Re: videos

#2

Re: videos

Chip Peterson

>Bill Grumbine's bowl turning video is excellent.

Re: videos

#3

My recommendation *LINK*

Jay in TX

>My recommendation is for Bill Grumbine's video. It takes you from tree to finished bowl. I do believe it is the most comprehensive video on the subject to date. I'm not sure, but I believe he advertises through this site as well.


Wonderful Wood

Re: videos

#4

Grumbine DVD and Ellsworth Gouge DVD

David Propst

>You will not find a better beginner DVD than Bill Grumbine's. I would also recommend David Ellsworth's Bowl Gouge DVD. These two are worth viewing repeatedly.

Best Regards,

David

Re: videos

#5

Re: videos

Turner

>I'd recommend the Del Stubbs video. There's a whole lot of technique in it that is timeless and low tech. I haven't seen the other ones mentioned (yet), so cannot comment on them.

Re: videos

#6

Re: videos

JimQ

>Richard Raffan Turning Bowls & Turning Boxes and his others are all good DVD's.

JimQ

Re: videos

#7

Re: videos

David

>I had a problem with a Raffan video, I do not recall the name, but he goes throgh the basics, and does a few projects as well - bowls, boxes, spindle exercises, etc.

The problem was that the view was frequently not close enough. You could see body position around the lathe, but you could not see the presentation of the tool to the wood very well. It was difficult to see presentation of the tools to the grinder for the same reason. It is a helpful video if you've got some of the real basics down, but if you haven't turned on the lathe before, I don't think I'd recommend it.

Sorry I can't remember the name.....

I will say that based on reading about it on his site, and the myriad comments I've seen on this message board over the course of time, I am going to get the Bill Grumbine video as a Christmas present - probably the first time I've specifically requested something for Christmas in five years.

David B.

Re: videos

#8

Re: videos

Gary Ljostad

>I agree, Bill Grumbine's vidio is about the best all around bowl turning vidio out there. And Bill is great guy. The other vidio I like, is the first vidio on woodturning that I watched when I started out, it's Turning Green Wood by Michael O'Donnell.

Re: videos

#9

Re: videos

Norm Smith in Nova Scotia

>I havent seen the Ellsworth tape but I have seen a few. The Grumbine DVD is by far the best. After watching it you feel as though you know the guy.

Norm

Re: videos

#10

Re: videos

Dennis Taylor

>Bill's video is by far the best on bowl turning, I learned so much, and you are correct almost feels like you know him after the video is over, but I watch it over & over, I can almost recite the words now myself.....The Del Stubbs video is good also, learned a lot of techniques there....the Stubbs video can be had from the local library here, so maybe your's also, and it is free!....Dennis

Re: videos

#11

Re: videos

kevinT in T Bay

>Picked the same one up when the shut down the Video division of the Library...50 cents... Good video. Put out by "Fine woodworking magazine". 120minutes.

Re: videos

#12

Don't forget about......

Nick Stagg

>the Chris Stott videos, they are as good as they get, in my opinion. There are nine altogether, with one just on bowl turning. I think you'll like the way he presents the material.

Nick

Re: videos

#13

Re: My recommendation

DougJ in Crawfordsville, IN

>Bill Grumbine's DVD is my choice as well