Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Round tool holder *LINK*

Posts

Round tool holder *LINK*

#1

Round tool holder *LINK*

Mike from St. Clair Shores

>I just finished building a hollowing rig, and I need several tool holders ( 1/4, 3/16, 1/8 ) to attach to the end of the rig. I placed an order about a month ago with Behemoth Tools but I think they have gone out of business. Phone disconnected and no response to e-mails. PayPal is looking into it. The holders I am looking for are about as big as a quarter up to 1/2 inch thick with a slot running thru it to hold the cutters. I have tried to include a photo, but not sure if it worked. Anyone out there with some info would sure be appreciated.

Mike


img

http://behemothtools.tripod.com/id4.html

Re: Round tool holder *LINK*

#2

Re: Round tool holder

MP Wall

>Look up Don Pencil, he sells faceplates and the scorpion/stinger hollowing tools and may sell you just the parts that you need. I haven't seen his name come up lately or looked at his website recently but he should be able to help. Another one to contact may be Lyle Jaimeson who sells his hollowing rig and may sell you spare parts that you can use. MP Wall

Re: Round tool holder *LINK*

#3

Re: Round tool holder

theeviltwinn

>I made my own. It wasn't too hard. I made it to hold 1/4" bits

I started with some 3/4 wide by 3/8 thick bar stock clamped in a vise with the 3/4 side up and sticking out from the end of the vise jaws. First I drilled a hole for the bolt about 1/2" in from the end and centered in the 3/4" direction. I don't remember the drill size. It is whatever fits the bolt on the end of the tool. Next I cut the slot right next to the hole. I clamped a piece of angle along where I wanted to cut as a guide and used a hacksaw to make a cut a little less than a 1/4". I moved the guide angle over and made a second cut for the other edge of the slot also making the slot a little less than 1/4" wide. I cleaned up the center of the slot with an angle grinder and a cut off wheel and touched up the slot with a file unil the cutter fit properly.

Now all that was left to do is to cut off the disc and make it round. I cut the disc as round as I could with the grinder. Then I slid a bolt through the hole and put a nut on fasntening the disc to the head of the bolt. I put the bolt into my drill, clamped the drill in the vise and turned it on. I then used the angle grinder with a grinding disc to make the piece round. A file cleaned everything up. Done!

I know all the machinist out there are laughing at me but for the limited tools I have it worked. Just take your time and work carefully.

Mike

Re: Round tool holder *LINK*

#4

Laughing ? I am NOT !!!

Fred in NC

>I have made many a jig and fixture with hand tools before I started buying power tools. I made a radius cutter out of a block of aluminum with nothing but a hacksaw and drill press. It can turn a ball at the end of a shaft. If you can do it with hand tools, go ahead ! Takes more time, but it is the results that count !

Re: Round tool holder *LINK*

#5

Try Craft Supplies USA -- They aint...

Paul in Phoenix, AZ

>...cheap. It's to bad Behemoth (sp) tools is gone. He was a good inexpensive source for those cuter holders. Several guys in our club here in Phoenix got burned as well. We feel your pain.

Re: Round tool holder *LINK*

#6

Anybody have the dimensions? .

Fred in NC

>Maybe I can make some of them. I will need the outside diameter, thickness, and size of center hole, and if tapped for a screw, the thread size.

When I retire in a couple months I will be making some metal tools and accessories. My time right now is more limited, but I have the equipment, and maybe able to help.

Replace 'AT' with the symbol on top of the 2 in your keyboard for my email address.

Re: Round tool holder *LINK*

#7

Email address

Fred in NC

>

Re: Round tool holder *LINK*

#8

Re: Email address

Fred in NC

>fredlidoATbellsouth.net (replace the AT with @)

Re: Round tool holder *LINK*

#9

Round tool holder - PROTOTYPE .

Fred in NC

>Quick pic with bad color. It is bright steel. This one will hold a 1/4" bit. I am shipping it to Mike to try out.


img

Re: Round tool holder *LINK*

#10

Don Pencil

Re: Round tool holder - PROTOTYPE .

Don Pencil

>It should work very well if mounted on the right kind of tool bit holder. It is identical to the Scorpion rotating bit holder.

For more info on these see WWW.DONPENCIL.COM.

Be Well,

Don Pencil


img

Re: Round tool holder *LINK*

#11

Re: Round tool holder - Thanks Don .

Fred in NC

>Will remember that, thanks for posting the pic.

Re: Round tool holder *LINK*

#12

Re: Round tool holder - PROTOTYPE .

JKJ in East TN

>Fred,

I'd be interested in purchasing one or more (no hurry!). 1/4, 3/16, and 1/8" slots.

I wonder if a useful design would be one with several slots cut into the same disk. For example, cut a 1/4" slot on one side and a 1/8" or 3/16" (or both) on the other. To cut more than two channels, at least two would need to cross on opposite sides, but I suspect the steel would still be strong enough. On the other hand, it might be best to just make several different sizes since the steel stock should be cheap enough and the labor the same.

JKJ