Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Slipped Ring Bowl - How to photos

Posts

Slipped Ring Bowl - How to photos

#1

Slipped Ring Bowl - How to photos

Russ Fairfield

>There were several massages asking how I made this one. At least one of you has already figured it out. For the rest, here is how I did it.

I started with this bowl in the photo. I turned the outside to shape. It was made into a rather global form for the purpose of being able to use a round feature ring. Any other shape would riquire making either an eliptical ring or one that was very wide.

In the end, everyone likes the roundness of this bowl.


img

Re: Slipped Ring Bowl - How to photos

#2

Re: Slipped Ring Bowl - How to photo 2

Russ Fairfield

>Then it was to the bandsaw to make the 1st cut.


img

Re: Slipped Ring Bowl - How to photos

#3

Re: Slipped Ring Bowl - How to photo 3

Russ Fairfield

>The bowl was cut into 2 pieces.


img

Re: Slipped Ring Bowl - How to photos

#4

Re: Slipped Ring Bowl - How to photo 4

Russ Fairfield

>The bar guide bar on the jig was relocated to make the 2nd cut to remove the tapered section. No special meansuements, just an eyeball guess.

The section that was removed is sitting on the saw table. This is the shape that will have to be made to replace it.


img

Re: Slipped Ring Bowl - How to photos

#5

Re: Slipped Ring Bowl - How to photo 5

Russ Fairfield

>Here is the bowl with the replacement ring glued in place. The dimensions and taper are not an exact fit, but there is enough (barely) wood on the inside to make it round again.

The tapered rings were made as flat rings, and then sawn to the taper with an adjustable resaw fence. The ring was attached to the fence with carpet tape, and the entire fence pushed through the saw, using a guide bar in the table slot. All cuts were made with a 3/8 X 10tpi blade.

I sanded each ring to smooth the saw cuts with a 14" sanding disc attached to the outboard side of the lathe spindle.

I am making a 2nd bowl with the finished ring looking similar to this one, and another with 2 rings. The 2 ring bowl will have one like this, and another that is turned to smooth with the bowl form.


img

Re: Slipped Ring Bowl - How to photos

#6

Re: Slipped Ring Bowl - How to photo 6

Russ Fairfield

>The finished bowl on the lathe. Turning the outside was easy. Turning the inside was a horror with the intermittent cuts. I did it with a bowl gouge, carefully.


img

Re: Slipped Ring Bowl - How to photos

#7

Re: Slipped Ring Bowl - The finished bowl

Russ Fairfield

>This is the same photo that I had posted several weeks ago.


img

Re: Slipped Ring Bowl - How to photos

#8

Re: Slipped Ring Bowl - The finished bowl

Bill Stehman ... AZ

>Thanks for sharing Russ, Your creativity is outstanding and the tapered ring brings it all out. Cutting the inside might make my hair stand !

Re: Slipped Ring Bowl - How to photos

#9

Re: Slipped Ring Bowl - The finished bowl

Jorge Castaneda

>Very ingenious Russ, very laborious too.

Thank you for sharing your method

Keep 'em coming1

Jorge

Re: Slipped Ring Bowl - How to photos

#10

Re: Slipped Ring Bowl - thanks for sharing

gary clarke

>

Re: Slipped Ring Bowl - How to photos

#11

Re: Slipped Ring Bowl - How to photos

RevDoug

>Thank you, Russ. It's not often that a great will give a step-by-step how-to. You are indeed a gentleman.

Turn 'em round,

Re: Slipped Ring Bowl - How to photos

#12

Re: Slipped Ring Bowl - How to photos

Ron in Drums PA

>Thanks Russ

Re: Slipped Ring Bowl - How to photos

#13

Thank you Russ! & a Ques

Dominic Greco in Richboro PA

>Russ,

This is some GREAT information you're giving away here Russ! I hope this becomes an article! (Hint Hint Garrett!)

I read how you used the jig at the bandsaw to cut the tapered rings. Needless to say, it sounds a bit complicated,...but cool. However, I'm assuming you made the rings "whole" (one completed glued up ring) and then used the resaw fence jig to cut the taper. Is that right?

If so, then the resaw capacity of your bandsaw would limit the diameter of the feature ring you could taper. (not that this matters a heck of a lot). For larger rings, I guess if you had a surface sander, you could build a jig to taper the rings. Your thoughts?

See ya around,

Dominic

Re: Slipped Ring Bowl - How to photos

#14

Re: Yes, and Yes

Russ Fairfield

>Dominic,

Yes, the tapered rings were cut whole; and yes, I am limited by the height of the bandsaw. However, I am now using a 9" riser block on the saw, so that gives me a 15" vertical cutting height. It seems to be working quite well, and I don't see any need for larger than that for awhile.

Re: Slipped Ring Bowl - How to photos

#15

It was a challenge to figure out.

kevinT in T Bay

>Thank you Russ for the challange. You made many here think...Instead of rightout giving up the method... It helped to keep the mind sharper than usual lately. Some differences in how we attacked the project. But, this way here, I'm not trying just to "reproduce your hard work". Learning is one thing ,but just copying others work( to me is just wrong). Thanks for enlighting us.. KevinT

Re: Slipped Ring Bowl - How to photos

#16

Re: Slipped Ring Bowl - The finished bowl

Curt Fuller

>Thanks much for the instructions and photos. I've gotta try that soon. Your bowl is just fantastic.

Re: Slipped Ring Bowl - How to photos

#17

Russ, thank you very much ! and ...

Fred in NC

>The inside cut would give me nightmares. From your description it is a very irregular shape, and very prone to a catch.

I had been thinking (well, trying to, anyway) and now you brought back to my mind some ideas I had a while back. Originally it had to do with knots and other irregularities inside of a bowl. Some of those will also produce a nasty catch. My idea had to do with roughing the inside until light cuts could be safely done.

Simply put, it is a round-cutting router bit of sorts. The motor sitting at one end of a long handle, and the bit at the other end. I think it can be made out of a Foredom or similar tool. It needs to turn at a very high speed, in the order of 30,000 RPM, so the bit needs to be of small diameter. The bowl would need to turn at a slow speed while cutting. This might sound contrary to normal turning practices, but who knows ???

Re: Slipped Ring Bowl - How to photos

#18

Re: Slipped Ring Bowl - How to photos

Ken Langenberger

>Nice bowl great idea and good photography to show details

Thanks Ken

Re: Slipped Ring Bowl - How to photos

#19

Re: Slipped Ring Bowl - How to photo 5

albertabob

>Russ:

Very neat idea.

Is there a jamb chuck pulled into the bowl on Photo 5?.

I noticed the tailstock sitting close by in the pic.

Rgds

Bob

Re: Slipped Ring Bowl - How to photos

#20

Re: Slipped Ring Bowl - How to photos

Rob Ceraso

>Russ -

Thank you for an excellent tutorial. You definitely got the creative juices flowing.

Rob

Re: Slipped Ring Bowl - How to photos

#21

Re: Slipped Ring Bowl - The finished bowl

David

>Thanks for letting us see behind the curtain!

Re: Slipped Ring Bowl - How to photos

#22

Re: Slipped Ring Bowl - How to photo 5

Russ Fairfield

>What you don't see is a plywood disc held against the top of the bowl to add support while I turned the outside. Then I used a steady rest on the outside while I turned the inside.