Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

A lesson it took too long to learn

Posts

A lesson it took too long to learn

#1

A lesson it took too long to learn

David

>I think I finally learned a lesson. I knew the mistake when I made it, but I've basically ignored the same mistake in the past without much consequence. Last night I lost a really nice piece of Boxwood Elder, and I think I've finally learned. This is a bit of an embarassing one, but in the spirit of the message board, I'll pass along my lessons eventually learned for those newer than me.

I decided to make a cone-shaped bowl with this piece last night, and was going to let it warp in paper bags, and had all these great plans. Shaped the outside of the bowl, it was just the way I wanted it (which means I'm getting better with the bowl gouge), and then cut a recess for the talon. Pause here:

IN FUTURE, DON'T BLOW OFF DRY FITTING THE TALON CHUCK AT THIS POINT.

I blew off dry fitting the chuck. Took the piece off the lathe, popped off the facelplate, spun it around and - at its smallest size, the talon jaws were barely too big. maybe 1/16". No problem, I'll just the smaller jaws. At their widest setting, the jaws were just barely too small to grab the wood. Prefekt. So I remounted the faceplate, and back to the lathe, where it was, as I knew it would be, slightly out of round. Well, I could reshape, but hey, all that smoothing work I just did, I would just ruin it, I'm impatient, so lets just open the recess. Pause here:

DON'T JUST OPEN THE RECESS UP. TRUE UP THE PIECE. THIS IS YOUR VERY LAST CHANCE TO DO THAT!!!

I just opened up the recess a bit, mounted up with the talon chuck, and started on the inside. I figured, as had happened with one or two mistakes of the past, that the wall thickness would be a little fatter on one side than the other.

Well, I can't really call it an explosion, but I now have a pretty good idea of what that would look like. (I did confirm with the busted up pieces that my toolwork has improved - the thickness was even and the work was pretty smooth. To my credit, I didn't even say bad words. I've never gotten overly upset about a lathe loss, because I'm still new, and am seeking the lesson out of every creamed piece. Pause here:

ALWAYS WEAR A FACE SHIELD!

I do! Didn't have to learn the hard way, just paid attention to posts here early on when I started turning.

Shame to lose the wood though. There was lots of blue streaking mixed in with the typical red. But, I extended an engraved invitation for a blow out, and got exactly what I asked for. The boxwood RSVP'd to my party.

It is safe to say I won't be making that particular mistake of laziness again. I'm done with that one. On and upward to the next mistake.

So, if you're a newbie - pay attention to this one, don't get lazy in your work: 1) Measure your chuck fit in advance, and when you know you need to fix something to be successful, fix it.

Sincerely,

A dummy

Re: A lesson it took too long to learn

#2

Re: A lesson it took too long to learn

David Galloway

>Thanks for the post! The most important lesson was one you already knew....ALWAYS wear a full face protection! Al Stirt really brought that home to me in a lesson, as did Dave Lancaster when I was in his shop. Because of their warnings, I have avoided major injury when such things happen....and they do regardless as to how careful and wise you are. Glad you are okay.....wood grows on trees!

David

Re: A lesson it took too long to learn

#3

Re: A lesson it took too long to learn

Molly Winton

>Good for you for sharing your lesson. It's one we 'older' turners have learned, or at least experienced, and it's good to pass on the knowledge to the 'youngsters'. I too am glad you were wearing full face protection.

Lately I've been going back and forth between just eye protection and the full shield. Yesterday I was working on a piece that came from Jim King (Peru), that had checking throughout and was like turning concrete it was so dense. I knew if it survived it was going to be gorgeous, but it had the potential of blowing up. To me it was worth the gamble, so I made sure I had my full face shield on when turning off the foot. Yup, KABOOM! Pieces and fragments flew everywhere with a few bouncing off my shield. I'm okay, but I would not have been if I were only wearing eye protection. I too took the time to examine the pieces to check my technical skills. I passed, thank goodness.

Re: A lesson it took too long to learn

#4

May I suggest?

Barry Irby

>Make a gage piece for each set of jaws. You can use a piece of plywood or sheet plastic. One end can be the smallest piece the jaws will grip and the other the largest. You could use a four sided piece and make them for the inside and outside of the dovetail jaws.

I would post a picture of mine, but they are crude and still in the prototype stage, but I see the value of them.

I too strongly recommend a full face shield. Failed to put mine on and had the stitches to prove the point. 28 stitches on the forehead, a third Eye, for a mere $1200.

Re: A lesson it took too long to learn

#5

Re: May I suggest?

David

>Thank you - that is probably the most clever suggestion I've been given on these message pages....ever - no offense to the dozens of people who have offered me advice in the past. Very "clean", very simple, very precise.

I keep all my smallish lathe tools (chucks, faceplate, etc., in a shoebox right behind me. (Except for facelplate screws which are kept in a finished disaster bowl that is ugly and mistake riddled it must never leave the shop) Guess there's another "tool" going in the shoebox.

Thanks for that - this will remove the temptation for further laziness.

David B.

Re: A lesson it took too long to learn

#6

Re: A lesson it took too long to learn

Carole in VA

>David, there is plenty of Box Elder out there so consider it a cheap lesson! The gauges eliminate the guess-work, provided (unlike me) you can find them when you need them! LOL

Re: A lesson it took too long to learn

#7

Fluorescent Orange

Brian Hahn in SW Wisconsin

>I painted my gauge fluorescent orange. Makes it a lot easier to find.

Re: A lesson it took too long to learn

#8

Re: Fluorescent Orange

David

>Yeah - I scizzored a guage out of clear plastic last night. It worked well, but was easily lost under the rubble.

Re: A lesson it took too long to learn

#9

Re: Fluorescent Orange

Paul in Phoenix, AZ

>Great Idea. I learn something here every day.

Re: A lesson it took too long to learn

#10

chuck guages

Ed Karch in No.VA

>Punch a hole in them and string them up along with a nice big steel nut. hang it on the magnet that you already have stuck to the cast iron side of your lathe. You do have one there dont you? Where do you stick your chuck key, engineer square and other necessary iron ware?

Re: A lesson it took too long to learn

#11

Re: chuck guages

David

>Shoebox on the workbench right next to the lathe. Reebox. My 3-year old absconded with all the magnets in the house.