Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Dull Glaser Gouge

Posts

Dull Glaser Gouge

#1

Dull Glaser Gouge

Phil Powell

>Does anyone here know how to ajust the Oneway Vari-Grind attachment so

that it sharpens a Glaser Gouger correctly?? The info that comes with the

Vari-Grind may not be totally worthless but it's pretty close. Everytime I try

sharpening the gouge I get a minor swept back finger nail shape (what I want)

but the sides aren't flat they are raised and extremely hard to turn with.

Am I the only one with this problem?

Re: Dull Glaser Gouge

#2

Re: Dull Glaser Gouge

Mark Kauder, Phenix City, AL

>Glaser Grinds by hand.

You will always get the type of grind you describe from the Vari-grind, because of the rotational action of the jig.

If you want a straight side, you will have to grind by hand.

Mark

Re: Dull Glaser Gouge

#3

Re: Dull Glaser Gouge

adrien

>Mark, I think Glazer uses a floor mounted wooden jig for sharpening his gouges. I'm no pro, but I haven't had a problem with using the Wolverine jig and a Glazer gouge. Perhaps Phil grinds the front of his gouge overmuch? I'm sure someone else here can come up with solution.

Re: Dull Glaser Gouge

#4

Re: Dull Glaser Gouge

John Lucas

>Phil What I do is grind the tool by hand to the desired shape. Then I play around with the angle of the wolverine, how far the jig is extended and even how long the bar is. Usually I can get the shape I want. You can get fairly straight sides by sliding the tool along the stone once you get to the side. Don't rotate the jig any further.

If this doesn't work you can make your own Ellsworth style jig fairly easy and change all the angles and lenghth of the rod to get almost any grind you want. I have 2 of those that I custom made for different tools.

Re: Dull Glaser Gouge

#5

Keith Tompkins

Re: Dull Glaser Gouge

Keith Tompkins

>Hi Phil, you have to experiment with the angle setting of the jig...you can loosten the wing nut then slide the base all the way back. That may be the grind you are looking for...can you post photos?

Re: Dull Glaser Gouge

#6

Re: Dull Glaser Gouge

Mike from St. Clair Shores

>Hi Phil,

I thought it was the oneway jig that was the problem also. Then one day an old timer in our club told me that going back and forth like the jig demands, cuts the front of he gouge more than it does the sides. Try to get your side profiles down by spending more time on that area. Then lighly finish the tip and as long as you're set at the right distance and angle you should be alright. Adrien mentioned this first and I thought I would elaborate.

Mike from St. Clair Shores

Re: Dull Glaser Gouge

#7

Re: Dull Glaser Gouge

Phil Powell

>Keith,

I have the jig folded up as tight as possible. Oneway says to start in the middle.

I did and lost a couple years of expensive steel from the gouge. I seem to get the

grind I'm looking for the way it's set now. But, I still have to mess with it. Next is

learn to sharpen without the crutch.

Re: Dull Glaser Gouge

#8

Re: Dull Glaser Gouge

Phil Powell

>Thanks Mike that made sense when I read it. I've tried it and

turns out to be a good idea.

Re: Dull Glaser Gouge

#9

Re: Dull Glaser Gouge

John Lucas

>Phil Get the AAW video on sharpening. John Jordans method for had sharpening is the best way I've tried. I usually sharpen a new gouge this way to the shape i want and then fit the wolverine to it.

Re: Dull Glaser Gouge

#10

Keith Tompkins

Re: Dull Glaser Gouge

Keith Tompkins

>Phil, once you get the setting you are happy with , it's a simple matter to reproduce the grind. this is one of the few instances where I recommend a jig over hand-held grinding skills. If a turner cannot constantly and reliably form the same grind by hand, then they cannot turn with any consistancy either. With the same grind, as done on a jig, you will learn EXACTLY how your tool will handle each time you use it.

Re: Dull Glaser Gouge

#11

Re: Dull Glaser Gouge

John Lucas

>Another trick with the Wolverine is when you get the grind you want and have everything locked down. Drill a hole through both plates. I used 3/32 drill bit. Now if I want to repeat that position after moving the plate I just put a 3/32 drill bit in and adjust it until it drops through both holes. Then I know it is exactly where I had it before.

Re: Dull Glaser Gouge

#12

Re: Dull Glaser Gouge

George Van in WI

>Phil, if you do get the grind you want and wish to duplicate the settings, you can make a stick to set the distance from the bottom of the "V" to the wheel and make a angle block indexing on the front of the Vari-grind to the leg of the Vari Grind to duplicate the angle. Most of my tools extend the same distance out of the jig. I have these for my different tools so I can repeat the same grind each time. They make changing quick and seem to work for me.