Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Why is it?

Posts

Why is it?

#1

Why is it?

Carole in VA

>That so many places that sell sandpaper skip directly from 220 to 320? Even the little wave sanding disks are like this. Sometimes I have a heck of time getting sanding scratches from 220 out with 320 paper and I can't find (locally) anything in between. Russ mentions 250 and 280 somewhere in his Corner (which is a valuable resource, I might add....thanks Russ) but those grits seem difficult to find.

Re: Why is it?

#2

Sandpaper

Don O.

>Carol, have you checked the Klingspor catalog. They have a dizzying assortment of grits. Hope this helps. Not sure if they have what you need.

Re: Why is it?

#3

Re: Sandpaper

John Lucas

>Are you sure it's the scratches from the 220? I have been going from 220 to 320 for years and haven't had a problem. What I do find is often times the 320 will show scratches that were left over from way on down the grit more than 220 does. It's not unusuall to have to go back to 150 to get them out. I try hard to sand so that I don't have to go back but sometimes on certain woods I will not see the bad scratches until I've gotten to 320. I hate it when that happens.

Re: Why is it?

#4

Re: Why is it?

Chris Andrew

>Carol,

Try dampening the piece with water after you've sanded with 220. This will raise the grain and swell the fibers from some of the deeper sanding scratches. You might find that the 320 is more effective after this treatment.

I keep a margarine container with water and a sponge handy for this and use my air gun to speed up the drying before I hit it with the 320. Jimmy Clewes suggests using denatured alcohol instead of water as it will dry faster.

Re: Why is it?

#5

Re: Why is it?

Ed Moore

>Carole,

Have you tried the 3X sandpaper from Norton? And, have you tried Abranet and Abralon. The latter is a fiber pad. They run from 180 to 4000 grit.

The 3X sandpaper is well worth the expense. If you use the paper in sequence it is quick and gets out scratches pretty well.

Abranet is a porous mesh that is really aggressive. It runs from 80 grit to 600. I just got an assortment from Supergrit - you must call them because their inventory is not all on the website.

Ed

Re: Why is it?

#6

Re: Why is it? *LINK*

Russ Fairfield

>You can buy either the 240 and 280 grit from OnLine Industrial Supply at the link. You will have to buy 50 sheets at a cost of about $13. This is a good quality no-load AluminumOxide paper.

For smaller quantities, you will have to find it at a local store, but at a higher price. Try Ace Hardware.


Sandpaper sheet

Re: Why is it?

#7

Re: Why is it?

Mark Kauder, Phenix City, AL

>Carol,

I agree with John.

It has been my contention that the sanding process requires that you go in small steps between grits, but not too small. I usually tell people that increasing each step about 50% numerically is about right. 60-100-150-220-320-400-600-1000-1500

Alternately you could go: 80-120-160-240-360-500-800-1200

I admit to frequently going from 60-80-100 and from 600-800-1000, but that is mostly 'cus I have the paper around. I probably will not replenish when the time comes.

Just my opinion. I get good results with this system. I learned it years ago sanding cars for my Dad - the glossy finishes on a car are much more revealing than wood.

Mark

Re: Why is it?

#8

Re: Why is it?

Michael Stafford

>Carole, if you have someone to share the cost you can buy sandpaper in bulk in a variety of grits from 60 to 600 including all the intermediate grits from Industrial Abrasives with hook and loop backing. A bunch of us did buy one sheet(36" x 39") of each grit and then cut it into strips. From there we cut it into 2" and 3" squares which work great on the round holders. About $15 a sheet... We bought 10 sheets which covered all the main grits, no 60. Really good paper also.

Re: Why is it?

#9

Are you using disk with an angle drill?

Dave Smith, Longview, WA

>Hi Carole,

If you are using a powered sanding set up? Here is a tip I haven't gotten around to submitting yet. Reverse the drill rotation each time you change disk to the next finer grit. Also, change rotation when using the first two grits in the progression. A word of caution on changing rotation. The sand paper will grab more than you will expect when changing rotation because it is going across the groves created by the opposite rotation.. An other thing, people press too hard when sanding which causes the grit to be ripped off the paper and produces excessive heat. An other thing to do is blow off the wood surface each time you change grits. The sanding grit that is ripped off from excessive pressure will happily sand with the successive finner paper for the random scratch effect. DAMHIKT

As you might expect I use denatured alcohol for sanding lubrication. It is amazing how well it works on tear out areas.

Dave Smith

Getting a little abrasive in Longview, WA..

Re: Why is it?

#10

Re: Sandpaper

Carole in VA

>That's probably what's happening John. The coarsest I use is usually 100 grit, but I try to have my finish cuts good enough to start with 120 or 150 since I favor tool work over sanding. It could be that I just can't see those scratches until I hit the 320-400 level. Sometimes I don't see them until I get even higher. It drives me nuts to have to go back through the grits. Going to try the water or alcohol thing on the next piece of scratch prone wood!

Re: Why is it?

#11

Re: Sandpaper

Russ Fairfield

>Yup, the more you sand, the more you have to sand. Some wood is worse than others for sanding scratches.

The problem is often those occasional larger grits that can invade even the highest priced sandpaper. You might try preconditioning your sandpaper by lightly raking the new piece over the sharp edge of a piece of steel a couple times. That breaks away any larger grits pieces that might be there. This works for sanding discs too, but be careful that it doesn't spin too many times.

Re: Why is it?

#12

Re: Why is it?

Russ Fairfield

>I use more grits in smaller increments for hand sanding than I do for the power sanding discs. Refining the scratch pattens is faster and less likely to leave coarser scratches behind with the smaller increments. I can get away with larger increments when I am using power, and use 60-100-150-180-240-320-400, all from Industrial Abrasives. It works for me.

Re: Why is it?

#13

Re: Sandpaper

David

>I had one along these lines over the weekend working with some cherry. Doing some bottom work on a box prior to cutoff, after having a coat of finishing oil on the rest of it. Catch! MRAAAWWWWW! "NOOOO!" Giant scratch circling the side. had to get out the 100 grit eraser and run through the series up to my usual 600. I checked it over very well before re-applying the oil, and hello, Mr. Highlighting pen, there's about half the scratch left. Went through the same deal with the erasers again, NOW the scratch is gone.

Re: Why is it?

#14

Re: Why is it?

georgetroy

>I use the Vic Wood 3" inertia sander. Will use Sorby 2" inertia if that doesn't work. Power Angle sanding is last resort for me. I get less scratches using the inertia. I can choose the speeds forward and reverse. I may start at 80 and work on up. It's like you start one or two grades higher. I stop at 800. GT

Re: Why is it?

#15

Re: Sandpaper

Bill Crommett

>Carole: I have used the intermediate grits you require from Klingspores. I don't know if the catalogue list the grits because I periodicaly go to thier Hickory store and scavange from the bargain bins.

Re: Why is it?

#16

Re: Are you using disk with an angle drill?

Carole in VA

>Hi Dave,

I figured some time ago out that reversing my drill helped. For the first grit, I will start in forward, then switch to reverse then back to forward for the last lap. With the next grit I start in reverse, switch to forward then finish in reverse, so on and so forth for each grit. Also figured out that a lighter touch is better. I am not getting the scratches that I used to when I first started turning, but any visible scratches at all drive me nuts. Russ also has a good point about breaking in the sanding disks to cut down any stray large particles, especially on the coarser grits. Be glad when my new lathe gets here. I think the reverse feature will great for sanding (though it won't necessarily help with the scratches)

Re: Why is it?

#17

Re: Why is it?

Rick Allen

>Hi Carol

www.sandpaper.ca has 2" discs in:

80, 100, 120, 150, 180, 220, 240, 320, 400, 600, 800, 1000, 2000, 2500, 3000

3" discs in:

80, 100, 120, 150, 180, 220, 240, 280, 320, 400, 500 600, 800, 1000, 2000, 2500, 3000

The prices are 3" 20 for $5 Canadian and 2" 30 for $5 Canadian. This is good sandpaper, good service and a terrific price.

BTW I agree with the others on the scratches were very likely from previous grits.

Re: Why is it?

#18

Re: Why is it?

Carole in VA

>Thanks Rick. I have bookmarked the site. I buy wave 2" wave discs from Perormance Abrasives. They are priced at 100/$13 US but they don't have anything higher than 800 grit.

Re: Why is it?

#19

Re: Why is it? *LINK*

Steve Worcester

>If you have eliminated the scratches from the previous grit, I think it is unnecessary to go from 220 to 240 to 280 to 320. The grit sizes between them are not that much. Then again, I would not recommend going from 240 to 400. I have a handy dandy grit comparison that I have posted that will tell you the differences in sizes, based on the grading system your manufacturer uses.

You can download it from here

Steve Worcester

www.turningwood.com


Grit Comparison Chart

Re: Why is it?

#20

Re: Overlooked element

JamieDonaldson

>Don't use a fluorescent light fixture or other diffused light source for sanding inspection. The missed grooves and other wood textures will show up much better under a directional light.

Re: Why is it?

#21

Re: Why is it?

vicmarc.fan

>Thank you. I just ordered some hard to find grits at a very good price if the quality is good.

Ron

Re: Why is it?

#22

Absolutely, totally true!

Mike Schwing from Md.

>Probably the simplest change one can make to improve their sanding performance, inspect your work under a more direct light source.

Re: Why is it?

#23

Is a regular light bulb OK?

Carole in VA

>I have flourescent lights in the shop but at the lathe I have one of those swing arm lights with a 75 watt bulb in it. Not as good as bright sunlight I'm sure!

Re: Why is it?

#24

Re: Are you using disk with an angle drill?

Barry

>I don't use an angle drill for power sanding. I use my old faithful 10-year old, 9.6 volt Panasonic cordless. It's much easier to control. I tried a Milwaukee angle drill in Lowes' and it just doesn't feel right in the hand. When my old Panasonic finally croaks, I'm buying another one.