Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Question on Watco Danish Oil

Posts

Question on Watco Danish Oil

#1

Question on Watco Danish Oil

Barry Irby

>I have turned a number of stools out of walnut and the client asked me to finish them with Watco Danish oil. I have wiped on about ten or twelve coats and have built a nice finish on them. Good depth and nice low gloss. I have been putting one or two coats a day on them and they remain somewhat tacky. Questions.

How long does it take for them to fully cure. I have them in an air conditioned space out of direct sunlight. It seems that each successive coat takes a little longer.

They have a few minor defects. A few dust particles and a few remaining dull spots. I am thinking of putting them back on the lathe and spinning them slowly and wet sanding them with some more Watco. Is this a good idea? Will I have to rebuild the finish? What grit should I use? Do I wait for them to fully cure or do it now? TIA

Re: Question on Watco Danish Oil

#2

Re: Question on Watco Danish Oil

tdaniel

>You are going too fast. Wait a couple of days between coats and more if still tacky. Wait a week before sanding so the finish can harden. Sanding with the oil is fine but when you get through wipe it well with a paper towel. Dry each coat as dry as you can get it with paper towels about 15 minutes after putting it on. The very last coat you might want to thin down and leave on the surface. Did I say use steel woold between coats?

TD

Re: Question on Watco Danish Oil

#3

Re: Question on Watco Danish Oil

robert davis

>i think you have applied too much watco too fast ..i have used watco on a number of pieces with no problems..no more than 3/4 coats shold be required.removing and starting over could be an option

Re: Question on Watco Danish Oil

#4

Re: Question on Watco Danish Oil

John K Jordan

>I agree. I use that oil and it takes me a couple of weeks. I let each coat dry at least a day, more if the humidity is high or the temperature low.

The first coat is a good soaking, as much as the wood can take over 10-15 minutes of applying. (Some people submerge the wood but I don't have that much oil.) Later coats I wipe on a liberal amount of oil, wait a few minutes, then wipe off any left on the surface with a dry cloth or paper towel. Then let it dry for at least a day, maybe two.

JKJ in East TN

Re: Question on Watco Danish Oil

#5

Re: Question on Watco Danish Oil

Glenn Madsen in the SF Bay area

>If you want a build, you may need to consider switching to a higher solids finish, such as a thinned (wiping) varnish. Watco is formulated to be more of an 'in the wood' finish.

Or consider something like a Beale buff with wax, perhaps?

Re: Question on Watco Danish Oil

#6

Re: Question on Watco Danish Oil

David

>I've seen a number of posts on the Watco oil. Can somebody post sample photos of projects you've used it on?

Thanks -

David B.

Re: Question on Watco Danish Oil

#7

Re: Question on Watco Danish Oil

Mike Schwing from Md.

>That is a good suggestion Barry. I would also recommend Waterlox. It builds much much more quickly and doesn't seem to suffer the "gummies" as readily.

One thing that wasn't mentioned is that if you ever need to remove excess Watco that more watco won't remove is that mineral spirits and steel wool work very well.

In your case, if you sit that thing on a shelf for a month or so the stickies will probably go away, but a quicker, probably better solution has been offered by the other respondants.

Re: Question on Watco Danish Oil

#8

Re: Question on Watco Danish Oil

Mike Schwing from Md.

>Here are a couple..

http://mysite.verizon.net/vzeo6om6/photos/photo4.jpg

http://mysite.verizon.net/vzeo6om6/photos/photo14.jpg

http://mysite.verizon.net/vzeo6om6/photos/photo22.jpg

http://mysite.verizon.net/vzeo6om6/photos/photo42.jpg

http://mysite.verizon.net/vzeo6om6/photos/photo51.jpg

Re: Question on Watco Danish Oil

#9

Re: Question on Watco Danish Oil

John K Jordan

>>I've seen a number of posts on the Watco oil.

>Can somebody post sample photos of projects you've used it on?

David,

Here's one, not the most exciting design (nor a pro photo!) but it is cherry, about 8-10 applications of *tinted* watco oil, Beale buffed.

JKJ in East TN


img

Re: Question on Watco Danish Oil

#10

Re: Question on Watco Danish Oil

John K Jordan

>This one is Lyptus, standard Watco oil.

BTW, Wataco is just a mixture of other oils (I forget what). There is no magic, you can mix up your own.

JKJ in East TN


img

Re: Question on Watco Danish Oil

#11

Re: Question on Watco Danish Oil

David

>Thanks VERY much for posting the photos and links. It really makes the wood look soft, gives it a very nice sheen. I've been playing with minwax products (tung oil and antique finish), and like them well enough, but I'm starting to run out of those and have been super-curious about using other oil-finishes.

David B.

Re: Question on Watco Danish Oil

#12

Re: Question on Watco Danish Oil

Ed Kelle

>Hi John

Thats a really nice piece there, I love the shape to it. Great job!

Re: Question on Watco Danish Oil

#13

Re: Question on Watco Danish Oil

Mac

>Hi David, If you will go to WOW site and look at the album listed for M Ray,you will see lots of Watco finished things. Just about everything there is finished with it.....Mac