Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Then I finished the bottom of the bowl, and....

Posts

Then I finished the bottom of the bowl, and....

#1

Then I finished the bottom of the bowl, and....

David

>Argh. Just sharing a little frustration. Now, I've only made about six bowls total, so there is the slightest possibility that I've got a few things more to learn.

I had a bowl mounted up on the lathe for a few days, and shaped the bottom just the way I wanted it, cut in a recess for the chuck, sanded it in grades to 600 (highest I've got), finished with minwax antique oil (Which is why it was mounted for several days), it was looking very good, feeling really smooth. Took it off the lathe, very careful not to ding it around, flipped it, put it on the chuck, made sure it was secure, fired up, and it held pretty solidly. Started squaring up the end, and was just about to start hollowing it when....it spun right off, dinking off the lathe and wheeling across the floor until it came to rest - thank goodness the pickax and then the wall were there to stop it. I think I started pleading "-bad word- NO! NO no no nono ohhhhhhh" before it even hit the floor.

Fortunately the damage wasn't too severe, so I didn't lose the wood, but I did have to start over and erase my sins. I'm not certain of the reason it popped off, but my money is on either the recess didn't have at least a 90 degree wall, or I was pushing the limits of good taste by using chuck jaws that were too small. Both situations corrected now. I guess I should be/am grateful for the lesson, but disappointed that the piece won't be quite as big as originally planned.

I rescued this from curbside, having asked the owner if it was ok (try explaining a wood lathe to an elderly man who is exceptionally hard of hearing, and how you are going to make a bowl out of his waste wood. His reaction was "well what do I care? Its at the curb!") It took me about an hour to cut the piece out from the curb with a bow saw, and probably another hour and a half to make a blank out of it in the basement. It has been anchor-sealed and drying since April. I was so patient letting it dry - it seems to be pretty stable - and then rolled it like a tire.

When I am finished, I'll post it, and you can help me decide what kind of wood it is. I think it is Beech. I might still have pics of the pre-lathed wood.

At least I haven't turned it into a lampshade. Yet.

Re: Then I finished the bottom of the bowl, and....

#2

Re: Then I finished the bottom of the bowl, and...

John K Jordan

>>I guess I should be/am grateful for the lesson,

>but disappointed that the piece won't be quite

>as big as originally planned.

I suspect everyone who turns has a number of pieces that started out with big intentions! I know I do. I have one beautifully delicate goblet turned from basswood (what a tricky wood) that unfortunately now has a base too small. And I was turning a bowl in a class with David Marks when my gently flaring lip design decided morphed into one with much straighter sides!

I've not yet thrown one out of the chuck (knock on bubinga), but the day I do, I hope I do it like you and not modify some body part. I remember a lad in shop class in 1964 who spun a bowl across the shop, off someone's head, and out through the window showering glass three stories down.

JKJ in East TN

Re: Then I finished the bottom of the bowl, and....

#3

Re: Then I finished the bottom of the bowl, and...

Mike Schwing from Md.

>David, hopefully you'll continue to do things like this for as long as you're a woodturner. They offer the chance to laugh at oneself, over and over again every time we think of them. They also serve as great reminders that we're not so fancy as we might think.

I recently blew up two bowls. One was less than 5 minutes from complete. One last final cut (just one more!) and the vac chuck exploited a weakness in the crotch figure and pulled the bottom right off of my bowl. The other I simply forgot that the piece had my old style tenon on it (integral to the bottom of the bowl vs waste wood) and turned it so thin it started to wobble. I shut the lathe off and intentionally whacked the rim hard with the handle of my gouge and that bowl became a funnel and a future glue block. I decided perhaps I should carve a few spoons before returning to the lathe...thus my recent spate of spoon carving.

Not too long ago I was completely finished with a work and went to turn the lathe off, but mistakenly turned off the vacuum instead. You can guess what happened. Didn't destroy that one but put a few dings in it I had to repair. That was one of my more vivid "you are the dumbest guy in the world" moments.

You're not alone.