Re: Wanna Buy A Used 1236?
Gerry in Maryland
>Hey Mark,
Ron's wife is gonna bronze that lathe when Ron meets his maker.. LOL
Gerry
Knowledge You Can Build On — Est. 1998
Re: Wanna Buy A Used 1236?
Gerry in Maryland
>Hey Mark,
Ron's wife is gonna bronze that lathe when Ron meets his maker.. LOL
Gerry
Re: Thinking of buying a new lathe
Barry Turner
>I have had a new Stubby 750 since January this year. My previous lathe was a Jet Mini. The Stubby is all (and more) lathe than I can envision ever needing. It is large enough for present and future needs. Everything works and works like it should! Power is never a problem (2 HP). It is heavy enough that even heavy out-of-balance blanks pose no problems. The variable speed control is flawless. I spent way too much money, but I got my money's worth.
Re: Thinking of buying a new lathe
Barry Irby
>I found a PVC coupling that was the right diameter for the post except for the little ring inside the collar, Drilled it out with a Forstner bit and cut it to length so that the gouge crosses the center of the bowl. It just slips on or off, snuggly so it does not fall off, but is easy to remove. I have found I almost never lower the rest, but occasionally I raise it for scraping. Cost less than fifty cents, took about ten minutes and eliminated a ton of aggravation. I also mad one for my McNaughton coring system. Works well, just set it in the banjo and go.
LOL
Ron In Drums PA
>
Re: Thinking of buying a new lathe
Barry Irby
>Bill, I have a DVR that is about two years old and am still very impressed. The new ones seem even better. Mine starts at 250 RPM and the one the club was using at the Woodcraft store starts at 100, but I'm not sure what I would want that for. You can actually see the lumps coming and aim the chisel at them separately. I think this is a great lathe. The stop feature mentioned above is a good one. If you get a big catch, it just stops and then starts again. If you do it about three times in quick succession it shuts down and you have to start again manually. Just touch the switch and go, but it's as if it's saying, "OK, get serious and pay attention." Also, if you start it with the shaft locked, it just beeps at you and quits, but of course, none of us would do that.
I think Russ' comments on checking shaft sizes and tapers are right on. A friend's lathe (we won't mention the brand Eh?) has a No2 taper in the tail stock and a No3 in the head stock. That would drive me nuts.
Short comings? It has a red STOP button and a green START button. They are not really buttons, just those little bulges in the control panel. They could be more TACTILE and in fact I have suggested they eliminate on and just make it a on and off button that has some sort of SLAP switch so you could just hit it, not have to find the right one. The banjo could be stronger. Speaking of tactile, I actually fixed one minor problem. I filled a notch int eh shaft lock?indexing knob. Now I can feel when it is in the right position. The notch lines up with the end of the lathe when the shaft locks.
I have mine on a shop built cabinet with a butcher block top and a column of sand under the head stock and six drawers. Works well.
Want to buy one cheap? Contact Tim Geist, their rep in West Virginia. He has reconditioned ones and used ones he sells for considerably less than new. Also has reconditioned Nova Chucks. I think I could stand to save a third for a lathe for students. Turn one good juicy piece of green walnut and they all look the same anyway.
Re: Thinking of buying a new lathe
woodspinner/ Bill Hale
>Oneway 2436 with 48 " out board end ways and banjo, 3 hp ac vs and you need no more. Under 24" I start inboard between centers, shape the outside and turn the tennon. I keep a jaw chuck on the outside, normally it has a hand wheel mounted in it, I move the blank outside and finish as if I was using a bowl lathe.
No fuss no muss just good easy turning. I have had mine for about 5 years and have never wanted anything else.
Good turning and be safe
Bill in Casa Grande, AZ.
Re: Thinking of buying a new lathe
Bill Grumbine (Kutztown PA)
>Thaks everyone, for your time and responses! While I suspected that I would get some, I had no idea I would get as many as I did.
Ted, I just may take you up on the VB 36 offer! Sarah is going to college in Beaver Falls for the next four years, so I will be driving by your house on a regular basis.
DD, I think that moving the lathe around is going to be important, especially in my shop. I have a Mini Max combo machine, and when the sliding table is off, there is a lot of room in one spot, but I need it back when I am sawing sheet goods up.
Steve, I hear you there. I might have the itch for something Canadian, but I don't have the scratch!
JL, John, Gerry, Tom, et. al., I like the Jet and recommend it on a regular basis. I really like the 3 phase motor it has, but for big stuff there is always the Poolewood. If I had another few hundred square feet, there would probably be no question, but the small footprint of the DVR is really attractive to me. AS it is I will probably have to grease it to get it in the shop!
Carole, whatever I end up with, you are welcome to come up and give it a spin before plunking your money down on one for yourself.
Russ, great minds think alike and all that. Both of these machines have the same size spindle as the Poolewood, so faeplates, chucks, etc can all be moved back and forth easily. I do not know about the post for coring, but I already had to have one made for Big Blue since it sports a 30mm tool rest post.
Steve, I don't know that anything can replace the Poolewood! It weighs 700 lbs in its current configuration, and is as stable as stable can be. It is virtually silent, and the potentiometer knob is not stuck at any particular rpm increment. I am familiar with the Nova 3000, as our local club has one and I have used it on several occasions. Not only that, the lathe I owned before the Poolewood was a Nova 1500. If I go with the DVR, I may have someone weld me up an A frame similar to what I have on the Poolewood now, and that would be virtually indestructable.
Ben, thanks for the heads up on the Woodfast, but the stands are of an older design and not really suited to big out of round blanks (I am sure that statement will make someone mad). But, I will lok into them just in case something has changed.
Barry T and Bill H, this is a third lathe, not my primary one. You guys have nice machines, but they ain't a Poolewood. ;-)
Barry I, you are the second person to recommend that I talk to Tim. I will be calling him Monday morning. I am just coming off five solid days of teaching, as well as selling the Mini Max, so I have a fist full of money to spend!
To those I might have missed, thanks again. So far the DVR is still in first place, mainly because of space, and because I might be able to get a deal on one as well. I will be sure to post the results of my search when I am done with it.
Bill
Just curious, Mark,
Gary Evans, Tallassee, TN
>What would be the use for a bed extension if you can't mount the tailstock on it? Inquiring minds want to know. 8^]
Gary
Re: Just curious, Mark,
Mark Kauder, Phenix City, AL
>I don't know about others, but when I am turning a hollow form that is 15-16" tall, and I am using a bowl steady, I was running out of maneuver room for the banjo/tool rest. With the bed extension, I am able to have a bowl steady on the main portion of the lathe bed, and the banjo/toolrest out on the extension.
The reason that Vega does not include the capability for installing the tailstock is: Because the Vega 2400/2600 tailstock bolts fast to the lathe, and does not slide along the bed, each tailstock is custom aligned to the headstock. If they were to include the capability on the bed extension, they could not assure tailstock alignment, and because of the small footprint of the lathe, there is probably some question about the effect on the center of gravity.
Mark
Blame Mark Kauder
Bill Grumbine (Kutztown PA)
>Well Mark had to go and talk about the Vega bowl lathe! Now he has me lusting after one. It looks like it will fit very nicely into the shop, perhaps even better than the DVR, and it will do some pretty impressive stuff. I am working on getting some time on one later on this week. Stay tuned for updates!
Bill