Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Buffs and carnuba

Posts

Buffs and carnuba

#1

Buffs and carnuba

Carole in VA

>I don't have a buffer so I got a couple of 3" bowl bufffs and some compounds to use with my Mini. The stick of Carnuba Wax is so darn hard I can hardly scrape it with my fingernail, much less load the buff with it. Is that stuff supposed to be that hard? Could it be old? I even tried holding it under the radiant heat lamp to soften it a little. :-(

Re: Buffs and carnuba

#2

Re: Buffs and carnuba

Jeremy in LA

>Carol that's the way it is. :) It's one of the hardest waxes available - that's why it's used to "protect" (at least protect a little). And it holds it's shine as a result of being so hard. Don't soften it or anything. When you "charge" the spinning buff, only hold the bar against the buff for about a second - no longer. It will seem like nothing happened. Trust that there's some on there. You just have to use the force :) It will become evident when you put wood to it. Happy buffing :)

Re: Buffs and carnuba

#3

Re: Buffs and carnuba

Terry Quiram

>Carol

Jeremy is correct. When I first started using my buff I really loaded the Carnuba and ended up streaking a couple pieces from apply too much wax. I used the rough end of a 2x4 to clean the wax off. It only takes a little and use a light touch.

Terry

Re: Buffs and carnuba

#4

Re: Buffs and carnuba

Barry Irby

>Carole,

Where did you get your buffs? I had a friend buff something for me and I'm so impressed I want the system. Got overwhelmed looking int eh various catalogs on line. Trying to figure out just what I need.

Barry Irby

Re: Buffs and carnuba

#5

Dick Hines

Re: Buffs and carnuba

Dick Hines

>Carole, don't drop the wax on the floor or you will have lots of very small pieces.

Re: Buffs and carnuba

#6

Dick Hines

Re: Buffs and carnuba

Dick Hines

>Barry, didn't Harry tell you where he got hes buffing system? Check Ray at Wood Craft he has them. I was in there today and there were a couple on the shelf.

Re: Buffs and carnuba

#7

Re: Buffs and carnuba

Carole in VA

>Dick has it right...Woodcraft. Be sure you get the spindle adapter and a taper.

Re: Buffs and carnuba

#8

Re: Buffs and carnuba

Carole in VA

>That hadn't occured to me, but now that you mention it, I suspect it would be like dropping a bar of glass! LOL Still don't see how any of that stuff ever gets transfered to the buff!

Re: Buffs and carnuba

#9

Heat

Russ Fairfield

>You said: Still don't see how any of that stuff ever gets transfered to the buff!

Heat. Carnauba melts at about 175F. The heat at the interface between the buffer fiber and the wax softens it enough to transfer to to the buffer and then to the wood.

Re: Buffs and carnuba

#10

Re: Buffs and carnuba

Barry Irby

>Thanks, Both of you, I was going to try Woodcraft, but just have not gotten there yet. You never can tell about Harry, he seems to have sources that are somewhat mysterious.

I was flipping through catalog sites on the net and one of them had "videos" of demos of products. One was Beale himself using the system. Many were the guy from American Woodshop. Now I can't find it again. If anyone knows where they are, let me know.

Re: Buffs and carnuba

#11

Re: Buffs and carnuba

Rduncan

>That's on the Woodcraft site.